Post-earthquake structural design for fire - a New Zealand perspective

On Tuesday 22 February 2011, a 6.3 magnitude earthquake struck Christchurch, New Zealand’s second largest city. The ‘earthquake’ was in fact an aftershock to an earlier 7.1 magnitude earthquake that had occurred on Saturday 4 September 2010. There were a number of key differences between the two events that meant they had dramatically different results for Christchurch and its inhabitants. The 22 February 2011 event resulted in one of New Zealand’s worst natural disasters on record, with 185 fatalities occurring and hundreds more being injured. In addition, a large number of buildings either collapsed or were damaged to the point where they needed to be totally demolished. Since the initial earthquake in September 2010, a large amount of building-related research has been initiated in New Zealand to investigate the impact of the series of seismic events – the major focus of these research projects has been on seismic, structural and geotechnical engineering matters. One project, however, conducted jointly by the University of Canterbury, the Fire Protection Association of New Zealand and BRANZ, has focused on the performance of fire protection systems in the earthquakes and the effectiveness of the systems in the event of post-earthquake fires occurring. Fortunately, very few fires actually broke out following the series of earthquake events in Christchurch, but fire after earthquakes still has significant implications for the built environment in New Zealand, and the collaborative research has provided some invaluable insight into the potential threat posed by postearthquake fires in buildings. As well as summarising the damage caused to fire protection systems, this paper discusses the flow-on effect for designing structures to withstand post-earthquake fires. One of the underlying issues that will be explored is the existing regulatory framework in New Zealand whereby structural earthquake design and structural design for fire are treated as discrete design scenarios.

[1]  Bassam A. Izzuddin,et al.  Experimental and analytical assessment of ductility in lightly reinforced concrete members , 2010 .

[2]  A. Hokugo,et al.  The Performance Of Fire Protection Of Buildings Against The Fires Following The Great Hanshin-awaji Earthquake , 1997 .

[3]  Colin Bailey,et al.  Behaviour of concrete floor slabs at ambient and elevated temperatures , 2007 .

[4]  Andrew H. Buchanan,et al.  Charring rates for double beams made from laminated veneer lumber (LVL) , 2013 .

[5]  Bertil Fredlund,et al.  Modelling of heat and mass transfer in wood structures during fire , 1993 .

[6]  Asif Usmani,et al.  Structural behaviour in fire compartment under different heating regimes — Part 1 (slab thermal gradients) , 2000 .

[7]  Jack P. Moehle,et al.  "BUILDING CODE REQUIREMENTS FOR STRUCTURAL CONCRETE (ACI 318-11) AND COMMENTARY" , 2011 .

[8]  Jeeho Lee,et al.  Plastic-Damage Model for Cyclic Loading of Concrete Structures , 1998 .

[9]  R. Dhakal.  STRUCTURAL DESIGN FOR EARTHQUAKE RESISTANCE: PAST, PRESENT AND FUTURE , 2011 .

[10]  D. B. Moore,et al.  The tensile membrane action of unrestrained composite slabs simulated under fire conditions , 2000 .

[11]  Kurt H. Gerstle,et al.  Behavior of Concrete Under Biaxial Stresses , 1969 .

[12]  Colin Bailey,et al.  Small-scale concrete slab tests at ambient and elevated temperatures , 2007 .

[13]  Donald Ballantyne.  Reliability and Restoration of Water Supply Systems Following Earthquakes , 1997 .

[14]  Jean-Marc Franssen,et al.  SAFIR. A thermal/structural program modelling structures under fire , 2003 .

[15]  Charles Scawthorn,et al.  Fire Following Earthquake , 1986 .

[16]  Stephen W. Tsai,et al.  A General Theory of Strength for Anisotropic Materials , 1971 .

[17]  Frank Fleer,et al.  Australian / New Zealand standards , 1996 .

[18]  Massimo Fragiacomo,et al.  "Numerical and experimental thermal-structural behaviour of laminated veneer lumber (LVL) exposed to fire" , 2010 .