Wireless Measurement of RFID IC Impedance

Accurate knowledge of the input impedance of a radio-frequency identification (RFID) integrated circuit (IC) at its wake-up power is valuable as it enables the design of a performance-optimized tag for a specific IC. However, since the IC impedance is power dependent, few methods exist to measure it without advanced equipment. We propose and demonstrate a wireless method, based on electromagnetic simulation and threshold power measurement, applicable to fully assembled RFID tags, to determine the mounted IC's input impedance in the absorbing state, including any parasitics arising from the packaging and the antenna-IC connection. The proposed method can be extended to measure the IC's input impedance in the modulating state as well.

[1]  Arpad L. Scholtz,et al.  Sensitivity and Impedance Measurements on UHF RFID Transponder Chips , 2008 .

[2]  P. Nikitin,et al.  Sensitivity and Impedance Measurements of UHF RFID Chips , 2009, IEEE Transactions on Microwave Theory and Techniques.

[3]  C. Dehollain,et al.  Remotely powered addressable UHF RFID integrated system , 2005, IEEE Journal of Solid-State Circuits.

[4]  H.T. Friis,et al.  A Note on a Simple Transmission Formula , 1946, Proceedings of the IRE.

[5]  Lauri Sydanheimo,et al.  Design and non-invasive design verification of a slot-type passive UHF RFID tag , 2010, 2010 IEEE Radio and Wireless Symposium (RWS).

[6]  Jeongjoon Lee,et al.  Full Wave Simulation of Flip-Chip Packaging Effects on RFID Transponder , 2007, 2007 IEEE International Conference on RFID.

[7]  A. Kishk,et al.  Chip Impedance Matching for UHF RFID Tag Antenna Design , 2008 .

[8]  K. Kurokawa,et al.  Power Waves and the Scattering Matrix , 1965 .

[9]  G. Iannaccone,et al.  Design criteria for the RF section of UHF and microwave passive RFID transponders , 2005, IEEE Transactions on Microwave Theory and Techniques.

[10]  Atef Z. Elsherbeni,et al.  The Finite-Difference Time-Domain Method for Electromagnetics with MATLAB® Simulations , 2015 .

[11]  G. Marrocco,et al.  The art of UHF RFID antenna design: impedance-matching and size-reduction techniques , 2008, IEEE Antennas and Propagation Magazine.

[12]  A. Harmouch,et al.  Miniaturization of the Folded Dipole Antenna , 2008, 2008 IEEE Lebanon Communications Workshop.

[13]  J. Tuovinen,et al.  Millimeter-Wave Identification—A New Short-Range Radio System for Low-Power High Data-Rate Applications , 2008, IEEE Transactions on Microwave Theory and Techniques.

[14]  Martin Fischer,et al.  Fully integrated passive UHF RFID transponder IC with 16.7-μW minimum RF input power , 2003, IEEE J. Solid State Circuits.

[15]  Raj Mittra,et al.  A Measurement Technique for Verifying the Match Condition of Assembled RFID Tags , 2010, IEEE Transactions on Instrumentation and Measurement.

[16]  Ikmo Park,et al.  Broadband RFID tag antenna with quasi-isotropic radiation pattern , 2005 .

[17]  Radford M. Neal.  Pattern Recognition and Machine Learning , 2007, Technometrics.

[18]  S.R. Best,et al.  On the significance of current vector alignment in establishing the resonant frequency of small space-filling wire antennas , 2003, IEEE Antennas and Wireless Propagation Letters.

[19]  R. Hansen.  Relationships between antennas as scatterers and as radiators , 1989, Proc. IEEE.

[20]  J. T. Cain,et al.  Statistical Analysis of Transponder Packaging in UHF RFID Systems , 2009, IEEE Transactions on Electronics Packaging Manufacturing.

[21]  Daniel M. Dobkin,et al.  The RF in RFID: Passive UHF RFID in Practice , 2007 .