Numerical simulation of three-dimensional flow and analysis of filling process in compression resin transfer moulding

In compression resin transfer moulding (CRTM), resin flows inside a mould filled with fibrous reinforcement as a result of resin injection and mould compression. This process facilitates the resin flow through the fibrous reinforcement particularly for high fiber content parts. This paper presents the numerical simulation of filling process of CRTM in full three-dimensional domain. A mathematical model of three-dimensional resin flow inside the CRTM mould is presented. An effective elastic modulus is introduced for multi-layer preforms connecting the mould closing speed to deformation rate of individual layers. Control volume/finite element method (CV/FEM) is used and the numerical algorithm developed to progress the flow front is based on a quasi-steady state approach, previously employed for resin transfer moulding (RTM), which is here modified for a deformable medium. Element characteristic height (ECH) and element characteristic surface area (ECSA) are introduced to take into account irregular elements in the simulation which are often observed in complex mould cavity. The numerical algorithm presented is coded and the resulting computer code is used to predict the necessary filling parameters such as flow progression, pressure distribution and mould clamping force. The validity of the numerical algorithm is verified by comparison with analytical solutions for simple moulds. Computer code developed is also used to analyse the CRTM process with different filling modes by providing various numerical examples. The results show the effectiveness of the numerical simulation in predicting the CRTM process.

[1]  Wen-Bin Young,et al.  Analysis of resin injection molding in molds with preplaced fiber mats. II: Numerical simulation and experiments of mold filling , 1991 .

[2]  L. J. Lee,et al.  Fiber mat deformation in liquid composite molding. I: Experimental analysis , 1993 .

[3]  Charles L. Tucker,et al.  Compression Mold Filling Simulation for Non-Planar Parts , 1990 .

[4]  S. J. Wineman,et al.  Consolidation Experiments for Laminate Composites , 1987 .

[5]  C. L. Tucker,et al.  Numerical simulation of injection/compression liquid composite molding. Part 2: preform compression , 2001 .

[6]  Andrew C. Long,et al.  Liquid Moulding Technologies , 1997 .

[7]  Hiroyuki Hamada,et al.  Effect of compression process on void behavior in structural resin transfer molding , 1996 .

[8]  Suresh G. Advani,et al.  A numerical approach to model non‐isothermal viscous flow through fibrous media with free surfaces , 1994 .

[9]  L. J. Lee,et al.  Fiber mat deformation in liquid composite molding. II: Modeling , 1993 .

[10]  Suresh G. Advani,et al.  Process Modeling in Composites Manufacturing , 2004 .

[11]  L. J. Lee,et al.  Non-isothermal Mold Filling and Curing Simulation in Thin Cavities with Preplaced Fiber Mats , 1991 .

[12]  F. Trochu,et al.  Numerical analysis of the resin transfer molding process by the finite element method , 1993 .

[13]  Timothy G. Gutowski,et al.  The Consolidation of Laminate Composites , 1987 .

[14]  J. Summerscales,et al.  The compressibility of a reinforcement fabric , 1995 .

[15]  Sunil C. Joshi,et al.  Mass conservation in numerical simulation of resin flow , 2000 .

[16]  C. L. Tucker,et al.  Numerical simulation of injection/compression liquid composite molding. Part 1. Mesh generation , 2000 .

[17]  Akbar Shojaei,et al.  Modeling and simulation approaches in the resin transfer molding process: A review , 2003 .

[18]  Constantina Lekakou,et al.  Compressibility and flow permeability of two-dimensional woven reinforcements in the processing of composites , 1996 .

[19]  W. Lee,et al.  Analysis of resin transfer/compression molding process , 1999 .

[20]  Akbar Shojaei,et al.  Numerical Simulation of Three-Dimensional Mold Filling in Resin Transfer Molding , 2003 .

[21]  L. Lessard,et al.  An Experimental Study of Saturated and Unsaturated Permeabilities in Resin Transfer Molding Based on Unidirectional Flow Measurements , 2004 .

[22]  Akbar Shojaei,et al.  Three-dimensional process cycle simulation of composite parts manufactured by resin transfer molding , 2004 .

[23]  Xuan-Tan Pham,et al.  Simulation of compression resin transfer molding to manufacture thin composite shells , 1999 .

[24]  W. Young,et al.  Study on Compression Transfer Molding , 1995 .

[25]  J. Bear.  Dynamics of Fluids in Porous Media , 1975 .

[26]  Woo Il Lee,et al.  Analysis of resin transfer moulding process with controlled multiple gates resin injection , 2000 .

[27]  Akbar Shojaei,et al.  Simulation of the three-dimensional non-isothermal mold filling process in resin transfer molding , 2003 .

[28]  A. Shojaei,et al.  Numerical simulation of three-dimensional mold filling process in resin transfer molding using quasi-steady state and partial saturation formulations , 2002 .

[29]  L. J. Lee,et al.  Analysis of resin injection molding in molds with preplaced fiber mats. I: Permeability and compressibility measurements , 1991 .

[30]  Joseph P. Greene,et al.  Analysis of an injection/compression liquid composite molding process , 1998 .

[31]  A. Shojaei,et al.  Numerical Analysis of Controlled Injection Strategies in Resin Transfer Molding , 2003 .

[32]  Simon Bickerton,et al.  Modeling and evaluation of the filling stage of injection/compression moulding , 2003 .

[33]  F. Trochu,et al.  Simulation of Compression Resin Transfer Molding with Displacement Control , 1998 .

[34]  François Robitaille,et al.  Compaction of textile reinforcements for composites manufacturing. I: Review of experimental results , 1998 .

[35]  Donald W. Taylor,et al.  Fundamentals of soil mechanics , 1948 .