Microstructure and mechanical properties of thixoformed GH4037 parts before and after heat treatment
暂无分享,去创建一个
Jufu Jiang | Ying Wang | G. Xiao | Ying Zhang | Yingze Liu | Minjie Huang
[1] Jing-jing Liang,et al. Microstructure and stress-rupture property of DD32 nickel-based single crystal superalloy fabricated by additive manufacturing , 2021, Journal of Alloys and Compounds.
[2] Y. Chun,et al. Effect of rare earth oxide addition on microstructure and mechanical properties of Ni-based alloy , 2021 .
[3] B. Zhong,et al. High cycle fatigue characterization of a nickel-based superalloy based on a novel temperature-dependent regression method , 2021 .
[4] Chong-yu Wang,et al. Alloying-element dependence of structural, elastic and electronic properties of nickel-based superalloys: Influence of γ’ volume fraction , 2020 .
[5] R. Caram,et al. Thixoforming of titanium: The microstructure and processability of semisolid Ti-Cu-Fe alloys , 2020 .
[6] Youho Lee,et al. Effect of heat treatment on microstructural evolution and creep behaviors of a conventionally cast nickel-based superalloy , 2020 .
[7] Jufu Jiang,et al. Microstructure and mechanical properties of thixoforged complex box-type component of 2A12 aluminum alloy , 2020 .
[8] Jufu Jiang,et al. Microstructure and mechanical properties of nickel-based superalloy GH4037 parts formed by thixoforming , 2020 .
[9] W. Niu,et al. Effect of sintering temperature and heat treatment on microstructure and properties of nickel-based superalloy , 2020 .
[10] Xu Bin,et al. Solidification microstructure of Cr4Mo4V steel forged in the semi-solid state , 2020 .
[11] K. Kakehi,et al. Effect of yttrium addition on creep properties of a Ni-base superalloy built up by selective laser melting , 2020 .
[12] Huiping Li,et al. EBSD study of the effect of electropulsing treatment on the microstructure evolution in a typical cold-deformed Ni-based superalloy , 2019 .
[13] H. Ding,et al. Effect of precipitates on high-temperature tensile strength of a high W-content cast Ni-based superalloy , 2019, Journal of Alloys and Compounds.
[14] Hong Wu,et al. Effect of heat treatment on mechanical property and microstructure of a powder metallurgy nickel-based superalloy , 2019, Materials Science and Engineering: A.
[15] M. Gussev,et al. In situ SEM-EBSD analysis of plastic deformation mechanisms in neutron-irradiated austenitic steel , 2019, Journal of Nuclear Materials.
[16] Xi Chenyang,et al. Preparation of ultrafine-grained GH4169 superalloy by high-pressure torsion and analysis of grain refinement mechanism , 2019, Journal of Alloys and Compounds.
[17] K. Berent,et al. Microstructure and mechanical properties of Mg–Zn–RE–Zr alloy after thixoforming , 2019, Journal of Materials Research and Technology.
[18] Zheli Feng,et al. Comparison of microstructures and mechanical properties of Inconel 718 alloy processed by selective laser melting and casting , 2018 .
[19] Yao Tang,et al. Partial melting behaviors and thixoforming properties of cast and extruded Mg-5.15Y-3.75Gd-3.05Zn-0.75Zr alloys , 2018 .
[20] Chang Li,et al. Investigations of γ′, γ″ and δ precipitates in heat-treated Inconel 718 alloy fabricated by selective laser melting , 2018 .
[21] Xiao-feng Sun,et al. Temperature dependence of tensile properties and deformation behaviors of nickel-base superalloy M951G , 2017 .
[22] K. Yagi,et al. Microstructural degradation and its corresponding mechanical property of wrought superalloy GH4037 caused by very high temperature , 2017 .
[23] T. J. Chen,et al. Effects of mold temperature on the microstructure and tensile properties of SiCp/2024 Al-based composites fabricated via powder thixoforming , 2016 .
[24] Jialin Gu,et al. Temperature effect on the low cycle fatigue behavior of a directionally solidified nickel-base superalloy , 2016 .
[25] M. Brochu,et al. Effect of heat treatments on microstructure evolution and mechanical properties of blended nickel-based superalloys powders fabricated by laser powder deposition , 2016 .
[26] Qiang Chen,et al. Effect of compound loading on microstructures and mechanical properties of 7075 aluminum alloy after severe thixoformation , 2016 .
[27] K. Yagi,et al. Assessment of service induced degradation of microstructure and properties in turbine blades made of GH4037 alloy , 2016 .
[28] Mark Hardy,et al. Effects of microstructure on high temperature dwell fatigue crack growth in a coarse grain PM nickel based superalloy , 2015 .
[29] Q. Feng,et al. Microstructural evolution and deformation features in gas turbine blades operated in-service , 2015 .
[30] K. Yagi,et al. Evaluation of a serviced turbine blade made of GH4033 wrought superalloy , 2014 .
[31] Q. Feng,et al. Paired Dislocations and Their Interactions with γ′ Particles in Polycrystalline Superalloy GH4037 , 2014, Journal of Materials Engineering and Performance.
[32] R. Misra,et al. An electron backscattered diffraction study on the dynamic recrystallization behavior of a nickel–chromium alloy (800H) during hot deformation , 2013 .
[33] Z. Zhong,et al. Tensile Properties and Deformation Characteristics of a Ni-Fe-Base Superalloy for Steam Boiler Applications , 2013, Metallurgical and Materials Transactions A.
[34] J. Pierret,et al. Characterization of thixoforming process of 100Cr6 steel , 2010 .
[35] H. Jirková,et al. Unconventional structure of X210Cr12 steel obtained by thixoforming , 2010 .
[36] J. Zhang,et al. Effect of Mo concentration on creep properties of a single crystal nickel-base superalloy , 2010 .
[37] R. Reed,et al. Heat treatment of UDIMET 720Li: the effect of microstructure on properties , 1999 .
[38] Merton C. Flemings,et al. Behavior of metal alloys in the semisolid state , 1991 .