Fuels by pyrolysis of waste plastics from agricultural and packaging sectors in a pilot scale reactor

Abstract The pyrolysis of waste plastics (so called chemical recycling) is one perspective way of their utilizations, but the end product properties are a key point of the industrial leading of processes. In this paper a pilot scale pyrolysis process has been investigated. Waste plastics were decomposed in a tube reactor at 520 °C, using hourly feed rate of 9.0 kg. Raw materials were selectively collected wastes from agricultural and packaging industry. For supporting the more intensive cracking of C C bonds of main polymer structure a commercial ZSM-5 catalyst was tested in concentration of 5.0%. Products were separated into gases, gasoline, light and heavy oil by distillation. Plastic wastes could be converted into gasoline and light oil with yields of 20–48% and 17–36% depending on the used parameters. The gas and liquid products had significant content of unsaturated hydrocarbons, principally olefins. In the presence of ZSM-5 catalyst the yields of lighter fractions (especially gasoline) could be considerably increased and the average molecular weight of each fraction has decreased. Gasoline had C 5 –C 15 hydrocarbons, while light oil had C 12 –C 28 . The used catalyst has promoted the formation of i-butane in gases and affected the composition of both gasoline and light oil. Properties of products are advantageous for fuel-like applications, and they are able to increase the productivity of refinery. On the other hand the possibility for further utilization of products from pyrolysis basically was affected by the source and the properties of raw materials. Waste polyethylene from agricultural consisted of some elements from fertilizers (N, S, P and Ca), which could not be removed from the surfaces of raw materials by pre-treatment (e.g. washing). In that case significant concentration of N, S, P and Ca can be measured in all products, but the catalyst has decreased the concentration of impurities. Gasoline, light oil and heavy oil were nitrogen free and sulphur content was below 12 mg/kg in hydrocarbons obtained by the pyrolysis of polypropylene waste from packaging.

[1]  Jin Yang,et al.  Using the DTG curve fitting method to determine the apparent kinetic parameters of thermal decomposition of polymers , 2001 .

[2]  K. Takeda,et al.  Computer simulation of thermal degradation of poly(butylene terephthalate) and analytical problems of terephthalic acid in scission products , 2003 .

[3]  Tiziano Faravelli,et al.  Gas product distribution from polyethylene pyrolysis , 1999 .

[4]  D. Serrano,et al.  Catalytic conversion of polystyrene over HMCM-41, HZSM-5 and amorphous SiO2–Al2O3: comparison with thermal cracking , 2000 .

[5]  Paul N. Sharratt,et al.  Investigation of the Catalytic Pyrolysis of High-Density Polyethylene over a HZSM-5 Catalyst in a Laboratory Fluidized-Bed Reactor , 1997 .

[6]  Zhiming Gao,et al.  A kinetic study of thermal degradation of polypropylene , 2003 .

[7]  D. Serrano,et al.  Conversion of low density polyethylene into petrochemical feedstocks using a continuous screw kiln reactor , 2001 .

[8]  L. Ballice.  A kinetic approach to the temperature-programmed pyrolysis of low- and high-density polyethylene in a fixed bed reactor : determination of kinetic parameters for the evolution of n-paraffins and 1-olefins , 2001 .

[9]  G. Madras,et al.  Continuous distribution kinetics for ultrasonic degradation of polymers , 2000 .

[10]  Paul T. Williams,et al.  Catalytic pyrolysis of polyethylene , 2002 .

[11]  A. G. Buekens,et al.  Catalytic plastics cracking for recovery of gasoline-range hydrocarbons from municipal plastic wastes , 1998 .

[12]  W. Kaminsky,et al.  Thermal degradation of mixed plastic waste to aromatics and gas , 1996 .

[13]  A. Muto,et al.  Removal of organic chlorine compounds by catalytic dehydrochlorination for the refinement of municipal waste plastic derived oil , 2001 .

[14]  Andreas Hornung,et al.  Kinetic study on the thermal degradation of polypropylene and polyethylene , 1999 .

[15]  Isabel Cabrita,et al.  Pyrolysis of plastic wastes , 1999 .

[16]  Zhiming Gao,et al.  Calculation of activation energy from fraction of bonds broken for thermal degradation of polyethylene , 2003 .

[17]  K. Miura,et al.  Pyrolysis kinetics of ?-irradiated polypropylene , 2001 .

[18]  Richard Knight,et al.  Depolymerization of Polypropylene in an Induction-Coupled Plasma (ICP) Reactor , 2000 .

[19]  S. Karlsson,et al.  Py-GC/MS as a means to predict degree of degradation by giving microstructural changes modelled on LDPE and PLA , 2001 .

[20]  S. Oh,et al.  A kinetic analysis of thermal degradation of polymers using a dynamic method , 2000 .

[21]  A. Muto,et al.  Catalytic degradation of polyethylene into fuel oil over mesoporous silica (KFS-16) catalyst , 1997 .

[22]  S. Ucar,et al.  Liquefaction of municipal waste plastics in VGO over acidic and non-acidic catalysts☆ , 2003 .

[23]  R. Font,et al.  Semivolatile compounds in pyrolysis of polyethylene , 2003 .

[24]  Yusaku Sakata,et al.  Thermal and catalytic degradation of structurally different types of polyethylene into fuel oil , 1997 .

[25]  Arthur Jutan,et al.  FCC unit modeling, identification and model predictive control, a simulation study , 2003 .

[26]  Jerzy Walendziewski,et al.  Thermal and catalytic conversion of waste polyolefines , 2001 .

[27]  J. T. Riley,et al.  A study of chlorine behavior in a simulated fluidized bed combustion system , 2000 .

[28]  J. Yoon,et al.  Catalytic degradation of polystyrene over natural clinoptilolite zeolite , 2001 .

[29]  Paul T. Williams,et al.  Removal of organobromine compounds from the pyrolysis oils of flame retarded plastics using zeolite catalysts , 2008 .

[30]  Zhiming Gao,et al.  A thermogravimetric study on thermal degradation of polyethylene , 2003 .

[31]  Myoung-Jae Choi,et al.  Degradation of polystyrene waste over base promoted Fe catalysts , 2003 .