PFEM-based modeling of industrial granular flows

The potential of numerical methods for the solution and optimization of industrial granular flows problems is widely accepted by the industries of this field, the challenge being to promote effectively their industrial practice. In this paper, we attempt to make an exploratory step in this regard by using a numerical model based on continuous mechanics and on the so-called Particle Finite Element Method (PFEM). This goal is achieved by focusing two specific industrial applications in mining industry and pellet manufacturing: silo discharge and calculation of power draw in tumbling mills. Both examples are representative of variations on the granular material mechanical response—varying from a stagnant configuration to a flow condition. The silo discharge is validated using the experimental data, collected on a full-scale flat bottomed cylindrical silo. The simulation is conducted with the aim of characterizing and understanding the correlation between flow patterns and pressures for concentric discharges. In the second example, the potential of PFEM as a numerical tool to track the positions of the particles inside the drum is analyzed. Pressures and wall pressures distribution are also studied. The power draw is also computed and validated against experiments in which the power is plotted in terms of the rotational speed of the drum.

[1]  R. Nedderman.  Statics and Kinematics of Granular Materials: Euler's equation and rates of strain , 1992 .

[2]  Akhtar S. Khan,et al.  Continuum theory of plasticity , 1995 .

[3]  A. Huespe,et al.  Stability and robustness issues in numerical modeling of material failure with the strong discontinuity approach , 2006 .

[4]  Gustaf Gustafsson,et al.  Smoothed Particle Hydrodynamic Simulation of Iron Ore Pellets Flow , 2007 .

[5]  Kent Tano,et al.  Continuous monitoring of mineral processes with special focus on tumbling mills : a multivariate approach , 2005 .

[6]  Jian Fei Chen,et al.  Flow pattern measurement in full scale silos: final report on the BMHD/DTI Project , 1995 .

[7]  Eugenio Oñate,et al.  The particle finite element method: a powerful tool to solve incompressible flows with free‐surfaces and breaking waves , 2004 .

[8]  Bertil Pålsson,et al.  Validation of tumbling mill charge-induced torque as predicted by simulations , 2013 .

[9]  Eugenio Oñate,et al.  Melting and spread of polymers in fire with the particle finite element method , 2010 .

[10]  Gerhard A. Holzapfel,et al.  Nonlinear Solid Mechanics: A Continuum Approach for Engineering Science , 2000 .

[11]  J. Cante,et al.  Flow regime analyses during the filling stage in powder metallurgy processes: experimental study and numerical modelling , 2011 .

[12]  Martin Z. Bazant,et al.  Assessing continuum postulates in simulations of granular flow , 2009 .

[13]  Herbert Edelsbrunner,et al.  Three-dimensional alpha shapes , 1992, VVS.

[14]  J. M. Rotter,et al.  Correlation between the flow pattern and wall pressures in a full scale experimental silo , 2007 .

[15]  Eugenio Oñate,et al.  Modeling of ground excavation with the particle finite element method , 2010 .

[16]  Javier Oliver,et al.  A contact domain method for large deformation frictional contact problems. Part 2: Numerical aspects , 2009 .

[17]  P. Knupp.  Algebraic mesh quality metrics for unstructured initial meshes , 2003 .

[18]  R. Behringer.  Sands, Powders, and Grains: An Introduction to the Physics of Granular Materials , 1999 .

[19]  Eugenio Oñate,et al.  Advances in the particle finite element method for the analysis of fluid-multibody interaction and bed erosion in free surface flows , 2008 .

[20]  Wing Kam Liu,et al.  Nonlinear Finite Elements for Continua and Structures , 2000 .

[21]  Dong Wang,et al.  Particle finite element analysis of large deformation and granular flow problems , 2013 .

[22]  Paul W. Cleary,et al.  Charge behaviour and power consumption in ball mills: sensitivity to mill operating conditions, liner geometry and charge composition , 2001 .

[23]  A. Huespe,et al.  An implicit/explicit integration scheme to increase computability of non-linear material and contact/friction problems , 2008 .

[24]  E. Oñate,et al.  A coupled PFEM–Eulerian approach for the solution of porous FSI problems , 2012, Computational Mechanics.

[25]  J. Oliver,et al.  Numerical modeling of crack formation in powder forming processes , 2011 .

[26]  J. C. Cante,et al.  Particle Finite Element Methods in Solid Mechanics Problems , 2007 .

[27]  C. Dohrmann,et al.  A stabilized finite element method for the Stokes problem based on polynomial pressure projections , 2004 .

[28]  Gustaf Gustafsson,et al.  Mechanical characterization and modelling of iron ore pellets , 2012 .

[29]  Gangquan Si,et al.  Experimental investigation of load behaviour of an industrial scale tumbling mill using noise and vibration signature techniques , 2009 .

[30]  K. K. Rao.  Statics and kinematics of granular materials , 1995 .

[31]  R. Weyler,et al.  Finite element modelling of ejection cracks in powder metallurgy die compaction processes: case study , 2012 .

[32]  B. Clermont,et al.  Optimization of mill performance by using online ball and pulp measurements , 2010 .

[33]  X. Olivella,et al.  Experimental and numerical study of the die filling stage in powder metallurgy , 2005 .

[34]  Andreas Berggren,et al.  Prediction of mill structure behaviour in a tumbling mill , 2011 .

[35]  Javier Oliver,et al.  A contact domain method for large deformation frictional contact problems. Part 1: Theoretical basis , 2009 .