Development of an Electrical Capacitance Tomography system using four rotating electrodes

This paper presents an Electrical Capacitance Tomography (ECT) sensor scheme consisting of N segments linked in four groups, treated as single, extremely broad electrodes forming a 4-electrode sensor. This configuration is repeated along the pipe circumference, selecting different segments in order to form N/4 independent 4-electrode schemes. The response of this sensor is studied by means of Finite Element Method (FEM)-based simulations, and the results are compared to the response of a 12-electrode conventional sensor. The image reconstruction proved to have lower error when using the segmented sensor, and it is less sensitive to white noise affecting the measurements. A tomograph with 20 segments based on a FPGA core has been developed and tested using a test phantom. Results show that high values of inter-electrode capacitances and better image reconstruction can be achieved.

[1]  Hua Yan,et al.  Simulation Study of Capacitance Tomography Sensors , 1999 .

[2]  G. Hounsfield.  Computerized transverse axial scanning (tomography): Part I. Description of system. 1973. , 1973, The British journal of radiology.

[3]  V. V. Pickalov,et al.  1st World Congress on Industrial Process Tomography , 1999 .

[4]  Wuqiang Yang,et al.  Hardware design of electrical capacitance tomography systems , 1996 .

[5]  Yves Ladam,et al.  VISUALISATION OF TWO-PHASE GAS-LIQUID PIPE FLOWS USING ELECTRICAL CAPACITANCE TOMOGRAPHY , 2004 .

[6]  Kamiel S. Rezkallah,et al.  A capacitance sensor for the characterization of microgravity two-phase liquid-gas flows , 1999 .

[7]  Radosław Wajman,et al.  Electrical capacitance tomography: image reconstruction along electrical field lines , 2001 .

[8]  A Arko,et al.  Development of Electrical Capacitance Tomography for Solids Mass Flow Measurement and Control of Pneumatic Conveying Systems , 1999 .

[9]  Artur J. Jaworski,et al.  The design of an electrical capacitance tomography sensor for use with media of high dielectric permittivity , 2000 .

[10]  P. Marcal,et al.  Introduction to the Finite-Element Method , 1973 .

[11]  J. Alberdi Primicia,et al.  Simulation design of electrical capacitance tomography sensors , 2007 .

[12]  Brian S. Hoyle,et al.  Electrical capacitance tomography for flow imaging: system model for development of image reconstruction algorithms and design of primary sensors , 1992 .

[13]  J. C. Gamio,et al.  A comparative analysis of single- and multiple-electrode excitation methods in electrical capacitance tomography , 2002 .

[14]  Liang-Shih Fan,et al.  Electrical Capacitance Volume Tomography , 2007, IEEE Sensors Journal.

[15]  A L Stott,et al.  Analysis of non-ideal characteristics of an ac-based capacitance transducer for tomography , 2001 .

[16]  Saba Mylvaganam,et al.  Comparison of Different Measurement Protocols in Electrical Capacitance Tomography Using Simulations , 2007, IEEE Transactions on Instrumentation and Measurement.

[17]  Lihui Peng,et al.  Image reconstruction algorithms for electrical capacitance tomography , 2003 .

[18]  Maurice Beck,et al.  Tomographic imaging of two-component flow using capacitance sensors , 1989 .

[19]  Wuqiang Yang,et al.  Monitoring water hammer by capacitance tomography , 1996 .

[20]  Tomasz Dyakowski,et al.  Applications of electrical tomography for gas-solids and liquid-solids flows : a review , 2000 .

[21]  R. C. Waterfall,et al.  Calibration of capacitance tomography systems for liquid-liquid dispersions , 1998 .

[22]  J. V. Hatfield,et al.  Silicon-based miniature sensor for electrical tomography , 2004 .

[23]  Jon Fea Pang,et al.  A hardware development for optical tomography system using switch mode fan beam projection , 2005 .