A predictive hybrid force modeling in turning: application to stainless steel dry machining with a coated groove tool

This paper presents an hybrid numerical/analytical modeling for estimation of cutting forces in machining process. The approach dedicated to predict 3D cutting forces are based on a chip flow direction modeling coupled with plane strain numerical simulations. An equivalent uncut chip thickness, deduced from the chip flow direction, is used as an input parameter in the 2D FEM. Resulting 2D numerical cutting forces are thus obtained from FEM, and knowing the chip flow direction, tangential, radial, and feed forces are calculated. Cutting forces derived from the proposed approach are compared to experiments when machining 304L austenitic steel with a groove-coated tool under dry condition. To take into account the complex groove geometry, the real shape of the cutting tool used in experiments has been captured by means of a digitization procedure, and thus implemented in 2D plane strain numerical simulations. The approach is applied to the case of stainless steel turning over a great range of cutting conditions. Two chip flow direction modelings are considered for the cutting force decomposition where it is shown the good predictive capabilities of the proposed approach.

[1]  Jun Wang,et al.  Development of a Chip Flow Model for Turning Operations , 2001 .

[2]  Svetan Ratchev,et al.  Modelling and simulation of micro-milling cutting forces , 2010 .

[3]  I. S. Jawahir,et al.  Development of hybrid predictive models and optimization techniques for machining operations , 2007 .

[4]  Jie Sun,et al.  Modeling of cutting force under the tool flank wear effect in end milling Ti6Al4V with solid carbide tool , 2013 .

[5]  G. V. Stabler.  The Fundamental Geometry of Cutting Tools , 1951 .

[6]  Taylan Altan,et al.  Estimation of tool wear in orthogonal cutting using the finite element analysis , 2004 .

[7]  Thomas Hanusch,et al.  Performance evaluation of a coded structured light system for cultural heritage applications , 2007, Electronic Imaging.

[8]  R. H. Brown,et al.  The measurement of chip flow direction , 1966 .

[9]  N. Fang,et al.  A comparative study of the cutting forces in high speed machining of Ti–6Al–4V and Inconel 718 with a round cutting edge tool , 2009 .

[10]  Joaquim Salvi,et al.  Pattern codification strategies in structured light systems , 2004, Pattern Recognit..

[11]  Tuğrul Özel,et al.  Journal of Materials Processing Technology Computational Modelling of 3d Turning: Influence of Edge Micro-geometry on Forces, Stresses, Friction and Tool Wear in Pcbn Tooling , 2022 .

[12]  D. Aspinwall,et al.  3D FE modelling of high-speed ball nose end milling , 2010 .

[13]  Mohammed Nouari,et al.  Finite element modelling of the thermo-mechanical behavior of coatings under extreme contact loading in dry machining , 2011 .

[14]  Yingchun Liang,et al.  Tool edge radius effect on cutting temperature in micro-end-milling process , 2011 .

[15]  I. Yellowley,et al.  An upper-bound cutting model for oblique cutting tools with a nose radius , 1997 .

[16]  D. Agard,et al.  Microtubule nucleation by γ-tubulin complexes , 2011, Nature Reviews Molecular Cell Biology.

[17]  Binglin Li,et al.  Analytical prediction of cutting forces in orthogonal cutting using unequal division shear-zone model , 2011 .

[18]  P. X. Li,et al.  Predictability of tool failure modes in turning with complex grooved tools using the equivalent toolface (ET) model , 2000 .

[19]  Jun Wang,et al.  Development of a general tool model for turning operations based on a variable flow stress theory , 1995 .

[20]  Robson Bruno Dutra Pereira,et al.  Analysis of surface roughness and cutting force when turning AISI 1045 steel with grooved tools through Scott–Knott method , 2013 .

[21]  L. Deshayes,et al.  Analysis of an equivalent tool face for the cutting speed range prediction of complex grooved tools , 2007 .

[22]  Mohammed Nouari,et al.  Modeling of velocity-dependent chip flow angle and experimental analysis when machining 304L austenitic stainless steel with groove coated-carbide tools , 2013 .

[23]  O. B. Adetoro,et al.  Prediction of mechanistic cutting force coefficients using ALE formulation , 2010 .