Simultaneous optimization of the mechanical properties of postconsumer natural fiber/plastic composites: Phase compatibilization and quality/cost ratio

In this work, a simultaneous optimization by phase compatibilization of four mechanical proprieties (flexural and tensile moduli, impact strength, and tensile stress at yield) of natural fiber/plastic composites was performed with respect to raw materials cost. In particular, a recycled resin of postconsumer origin (blend of high density polyethylene and polypropylene) with flax fibers was extruded with an additives package: a coupling agent (maleic anhydride grafted polypropylene) and an impact modifier (maleic anhydride grafted ethylene octene metallocene copolymer) to improve the interface between each phase. Then, the compounds were injection molded and tested. The analysis was performed according to a Box-Behnken experimental design to study the effect of fiber concentration, total additives concentration, and impact modifier fraction in the additives package. The optimization process required three steps: to model the relationships between mechanical properties and selected factors by a multiple linear regression analysis, to identify the potentially optimum conditions using the desirability function approach (Derringer–Suich and Ch'ng et al.), and to determine the best composite composition (optimum condition) by a comparative analysis of the material quality/cost ratios. POLYM. COMPOS., 35:730–746, 2014. © 2013 Society of Plastics Engineers

[1]  Douglas C. Montgomery,et al.  Modified Desirability Functions for Multiple Response Optimization , 1996 .

[2]  Susan Selke,et al.  Wood fiber/polyolefin composites , 2004 .

[3]  G. Thomas,et al.  Wood fibers as reinforcing fillers for polyolefins , 1984 .

[4]  Mohini Sain,et al.  Interface Modification and Mechanical Properties of Natural Fiber-Polyolefin Composite Products , 2005 .

[5]  Sabu Thomas,et al.  A review on interface modification and characterization of natural fiber reinforced plastic composites , 2001 .

[6]  P. Herrera-Franco,et al.  Development and characterization of a HDPE-sand-natural fiber composite , 1997 .

[7]  Roberto Olayo,et al.  Effect of fiber surface treatment on the fiber-matrix bond strength of natural fiber reinforced composites , 1999 .

[8]  P. S. Gopala Krishnan,et al.  Studies on natural fiber reinforced isotactic polypropylene-ethylene-octene copolymer blend composites , 2012 .

[9]  Andrzej K. Bledzki,et al.  Unidirectional hemp and flax EP‐ and PP‐composites: Influence of defined fiber treatments , 2004 .

[10]  J. Balatinecz,et al.  Mechanical properties of wood‐fiber/toughened isotactic polypropylene composites , 1997 .

[11]  C. Hill,et al.  Silane coupling agents used for natural fiber/polymer composites: A review , 2010 .

[12]  M. Vallejos,et al.  Full exploitation of Cannabis sativa as reinforcement/filler of thermoplastic composite materials , 2007 .

[13]  I. Mondragon,et al.  Effects of fibre treatment on wettability and mechanical behaviour of flax/polypropylene composites , 2003 .

[14]  M. John,et al.  Recent Developments in Chemical Modification and Characterization of Natural Fiber-Reinforced Composites , 2008 .

[15]  J. Hodgkinson,et al.  Engineering and characterisation of the interface in flax fibre/polypropylene composite materials. Part II. The effect of surface treatments on the interface , 2002 .

[16]  B. Riedl,et al.  Reinforcement of Recycled Polyolefins with Wood Fibers , 1992 .

[17]  Abdullah Al Mamun,et al.  Polypropylene composites with enzyme modified abaca fibre , 2010 .

[18]  Jose Maria Kenny,et al.  Flax fiber surface modifications : Effects on fiber physico mechanical and flax/polypropylene interface properties , 2005 .

[19]  Nuno Ricardo Costa,et al.  Desirability function approach: A review and performance evaluation in adverse conditions , 2011 .

[20]  D. Rodrigue,et al.  Rheological properties of polypropylene/hemp fiber composites , 2009 .

[21]  K. Pickering,et al.  Optimising industrial hemp fibre for composites , 2007 .

[22]  T. Lundstedt,et al.  Experimental design and optimization , 1998 .

[23]  F. L. Matthews,et al.  Engineering and characterisation of the interface in flax fibre/polypropylene composite materials. Part I. Development and investigation of surface treatments , 2002 .

[24]  Kwang-Jae Kim,et al.  Simultaneous optimization of mechanical properties of steel by maximizing exponential desirability functions , 2000 .

[25]  Mehdi Tajvidi,et al.  Mechanical properties of composites from sawdust and recycled plastics , 2006 .

[26]  A. Błędzki,et al.  Biocomposites reinforced with natural fibers: 2000–2010 , 2012 .

[27]  I. Verpoest,et al.  Improving the properties of UD flax fibre reinforced composites by applying an alkaline fibre treatment , 2006 .

[28]  Sabu Thomas,et al.  Effect of chemical treatment on the tensile properties of short sisal fibre-reinforced polyethylene composites , 1996 .

[29]  K. Pickering,et al.  Engineering and evaluation of hemp fibre reinforced polypropylene composites: Fibre treatment and matrix modification , 2008 .

[30]  H. Low,et al.  A New Approach for Multiple-Response Optimization , 2005 .

[31]  Hota V. S. GangaRao,et al.  Critical review of recent publications on use of natural composites in infrastructure , 2012 .

[32]  I. Tavman,et al.  Effects of the atmospheric plasma treatments on surface and mechanical properties of flax fiber and adhesion between fiber–matrix for composite materials , 2013 .

[33]  Michael P. Wolcott,et al.  Effects of processing method and fiber size on the structure and properties of wood-plastic composites , 2009 .

[34]  I. Mondragon,et al.  Mechanical properties of flax fibre/polypropylene composites. Influence of fibre/matrix modification and glass fibre hybridization , 2005 .

[35]  M. Ragoubi,et al.  Impact of corona treated hemp fibres onto mechanical properties of polypropylene composites made thereof , 2010 .

[36]  L. Tabil,et al.  Chemical Treatments of Natural Fiber for Use in Natural Fiber-Reinforced Composites: A Review , 2007 .

[37]  T. Peijs,et al.  Effect of Compounding and Injection Molding on the Mechanical Properties of Flax Fiber Polypropylene Composites , 2010 .

[38]  Zong Zhi-yu,et al.  A new desirability function based method for multi-response robust parameter design , 2006 .

[39]  Zahid Saleem,et al.  Treating bast fibres with pectinase improves mechanical characteristics of reinforced thermoplastic composites , 2008 .

[40]  Haibo Han,et al.  Mechanical Properties of Injection-molded Natural Fiber-reinforced Polypropylene Composites: Formulation and Compounding Processes , 2010 .

[41]  Ful-Chiang Wu,et al.  Optimization of Correlated Multiple Quality Characteristics Using Desirability Function , 2004 .

[42]  Seyed Taghi Akhavan Niaki,et al.  Multi-response simulation optimization using genetic algorithm within desirability function framework , 2006, Appl. Math. Comput..

[43]  S. Kalia,et al.  Pretreatments of Natural Fibers and their Application as Reinforcing Material in Polymer Composites—A Review , 2009 .

[44]  Y. S. Negi,et al.  Recent Development in Natural Fiber Reinforced Polypropylene Composites , 2009 .

[45]  Abdullah Al Mamun,et al.  Influence of compounding processes and fibre length on the mechanical properties of abaca fibre-polypropylene composites , 2008 .

[46]  Smita Mohanty,et al.  Effect of MAPP as a Coupling Agent on the Performance of Jute–PP Composites , 2004 .

[47]  R. Långström,et al.  Microstructure and Strength of Injection Molded Natural Fiber Composites , 2007 .