Double-Exposure Grayscale Photolithography

A double-exposure grayscale photolithography technique is developed and demonstrated to produce three-dimensional (3-D) structures with a high vertical resolution. Pixelated grayscale masks often suffer from limited vertical resolution due to restrictions on the mask fabrication. The double-exposure technique uses two pixelated grayscale mask exposures before development and dramatically increases the vertical resolution without altering the mask fabrication process. An empirical calibration technique was employed for mask design and was also applied to study the effects of exposure time and mask misalignment on the photoresist profile. This technology has been demonstrated to improve the average step between photoresist levels from 0.19 to 0.02 mum and the maximum step from 0.43 to 0.2 mum compared to a single pixelated exposure using the same mask design.

[1]  B. Morgan,et al.  Vertically-Shaped Tunable MEMS Resonators , 2008, Journal of Microelectromechanical Systems.

[2]  B. Morgan,et al.  A new paradigm for high resolution 3D lithography , 2008, 2008 IEEE 21st International Conference on Micro Electro Mechanical Systems.

[3]  D. Joy,et al.  Controlling resist thickness and etch depth for fabrication of 3D structures in electron-beam grayscale lithography , 2007 .

[4]  W. Hsu,et al.  Enhancement on forming complex three dimensional microstructures by a double-side multiple partial exposure method , 2007 .

[5]  R. Ghodssi,et al.  Automated Two-Axes Optical Fiber Alignment Using Grayscale Technology , 2007, Journal of Microelectromechanical Systems.

[6]  Paul Crozat,et al.  Two- and three-dimensional microcoil fabrication process for three-axis magnetic sensors on flexible substrates , 2006 .

[7]  X. Le Roux,et al.  Design, Realization, and Characterization of 3-D Taper for Fiber/Micro-Waveguide Coupling , 2006, IEEE Journal of Selected Topics in Quantum Electronics.

[8]  B. Morgan,et al.  Advanced Techniques in 3D Photolithography for MEMS , 2006 .

[9]  Masayoshi Esashi,et al.  Fabrication of three-dimensional microstructure using maskless gray-scale lithography , 2006 .

[10]  D. Prather,et al.  Three-dimensional lithographical fabrication of microchannels , 2005, Journal of Microelectromechanical Systems.

[11]  Reza Ghodssi,et al.  Substrate interconnect technologies for 3-D MEMS packaging , 2005 .

[12]  Reza Ghodssi,et al.  Microfabrication of 3D silicon MEMS structures using gray-scale lithography and deep reactive ion et , 2005 .

[13]  Garrett Schneider,et al.  Fabrication of three-dimensional photonic crystals with multilayer photolithography , 2005, SPIE MOEMS-MEMS.

[14]  Hoang Yan Lin,et al.  Characterization of the gray-scale photolithography with high-resolution gray steps for the precise fabrication of diffractive optics , 2004 .

[15]  Satoshi Kawata,et al.  3D Patterning by means of nanoimprinting, X-ray and two-photon lithography , 2004 .

[16]  Ute Drechsler,et al.  SU-8 for real three-dimensional subdiffraction-limit two-photon microfabrication , 2004 .

[17]  Alan H. Epstein,et al.  Millimeter-Scale, Micro-Electro-Mechanical Systems Gas Turbine Engines , 2004 .

[18]  R. Ghodssi,et al.  Development of a deep silicon phase Fresnel lens using Gray-scale lithography and deep reactive ion etching , 2004, Journal of Microelectromechanical Systems.

[19]  Soo-Young Lee,et al.  Dose control for fabrication of grayscale structures using a single step electron-beam lithographic process , 2003 .

[20]  Xiaocong Yuan,et al.  Grey scale structures formation in SU-8 with e-beam and UV , 2003 .

[21]  Reza Ghodssi,et al.  Investigation of gray-scale technology for large area 3D silicon MEMS structures , 2003 .

[22]  Philippe Renaud,et al.  Microstereolithography: concepts and applications , 2001, ETFA 2001. 8th International Conference on Emerging Technologies and Factory Automation. Proceedings (Cat. No.01TH8597).

[23]  P. S. Hauge,et al.  Characterization of positive photoresist , 1975, IEEE Transactions on Electron Devices.

[24]  Reza Ghodssi,et al.  Compensated aspect ratio dependent etching (CARDE) using gray-scale technology , 2005 .

[25]  Hye-Keun Oh,et al.  A practical method of extracting the photoresist exposure parameters by using a dose-to-clear swing curve , 2003 .

[26]  Hans Joachim Quenzer,et al.  Microfabrication of complex surface topographies using grey-tone lithography , 1995 .

[27]  Guy Voirin,et al.  One-step 3D shaping using a gray-tone mask for optical and microelectronic applications , 1994 .