Investigating the effect of geometrical parameters on distortions in butt-welded plates

Welding-induced distortions are one of the major problems frequently encountered in industry. Different geometrical and welding process parameters are believed to influence distortions. One of the most common types of distortions frequently observed in butt-welded plates is angular distortion. In this study, the effect of geometrical parameters on angular distortions in butt-welded plates has been investigated numerically and experimentally. A comprehensive study has been performed, and several cases with different plate lengths, widths and thicknesses have been studied. Distortions have been predicted by three-dimensional thermo-elastic-plastic finite element simulation. The finite element results have been verified by a series of experimental measurements for temperatures and angular distortions. The results of this study revealed that plate thickness, length and width influence the magnitude and mode of distortions greatly. The results revealed that decreasing the plate thickness or increasing the weld length results in higher and nonlinear angular distortions. Increasing the plate width has an adverse effect and reduces the angular distortion. In addition, the thickness of the plate has a key role on distortion behavior and can lead to buckling in thin plates.

[1]  Tom Gray,et al.  Computationally efficient welding distortion simulation techniques , 2005 .

[2]  Pierluigi Mollicone,et al.  Procedural influences on non-linear distortions in welded thin plate fabrication , 2007 .

[3]  D. Deng FEM prediction of welding residual stress and distortion in carbon steel considering phase transformation effects , 2009 .

[4]  D. Deng,et al.  Prediction of welding distortion and residual stress in a thin plate butt-welded joint , 2008 .

[5]  Mohammad Sedighi,et al.  Effect of welding sequence and direction on angular distortions in butt-welded plates , 2012 .

[6]  Hidekazu Murakawa,et al.  FEM prediction of buckling distortion induced by welding in thin plate panel structures , 2008 .

[7]  M. S. Choobi,et al.  Investigation of the E ect of Clamping on Residual Stresses and Distortions in Butt-Welded Plates , 2010 .

[8]  Robert W. Messler,et al.  Principles Of Welding: Processes, Physics, Chemistry And Metallurgy , 2015 .

[9]  S. C. Park,et al.  Weldin g Distortion of a Thin-Plate Panel Structure , 1999 .

[10]  Hidekazu Murakawa,et al.  Determination of welding deformation in fillet-welded joint by means of numerical simulation and comparison with experimental measurements , 2007 .

[11]  P. Michaleris,et al.  Prediction of welding distortion , 1997 .

[12]  Xin Sun,et al.  Finite element analysis of thermal tensioning techniques mitigating weld buckling distortion , 1996 .

[13]  P. Michaleris,et al.  Mitigation of welding induced buckling distortion using transient thermal tensioning , 2003 .

[14]  Tom Gray,et al.  Computational prediction of out-of-plane welding distortion and experimental investigation , 2005 .

[15]  Wei Liang,et al.  Numerical simulation of welding distortion in large structures , 2007 .

[16]  村川 英一,et al.  Prediction of Welding Distortion during the Assembly Process of Thin Plate Structures (2^ Report) : Influence of Welding Sequence on Welding Distortion , 2004 .

[17]  P. Maropoulos,et al.  Prediction of welding distortion in butt joint of thin plates , 2009 .

[18]  A. Bachorski,et al.  Finite-element prediction of distortion during gas metal arc welding using the shrinkage volume approach , 1999 .

[19]  Zhili Feng Processes and mechanisms of welding residual stress and distortion , 2005 .

[20]  Mohammad Sedighi,et al.  Prediction of welding-induced angular distortions in thin butt-welded plates using artificial neural networks , 2012 .

[21]  Muhammad Abid,et al.  Prediction of welding distortions and residual stresses in a pipe–flange joint using the finite element technique , 2005 .

[22]  A. Dhingra,et al.  Numerical simulation of welding-induced distortion in thin-walled structures , 2005 .

[23]  V. Vel Murugan,et al.  Effects of process parameters on angular distortion of gas metal arc welded structural steel plates , 2005 .

[24]  T. Teng,et al.  Analysis of residual stresses and distortions in T-joint fillet welds , 2001 .

[25]  Hidekazu Murakawa,et al.  Numerical simulation of temperature field and residual stress in multi-pass welds in stainless steel pipe and comparison with experimental measurements , 2006 .