Influence of parallel wire placement on the AC copper losses in electrical machines

Due to high range and continious power requirements in electric and hybrid cars the efficiency of electrical machines is one key parameter. In this paper ac copper loss effects, mainly circulating currents, are investigated. A permanent magnet machine used for electric and hybrid cars showing 6 pole pairs, a maximum power of 80kW and a maximum speed of 12000 rpm is used for this analysis. In general parallel strands of small diameter are used to facilitate handling tasks and to minimize skin and proximity effects. But in the design process feasible circulating currents due to unsuitable strand distribution are often not considered. Furthermore the wire distribution is very often unkown due to automatic winding technology. So the main topic of this study is to analyze the impact of the parallel wires' placement based on the described machine and to propose a measurement technique which could be used later to judge automatically wound machines containing unknown strand placement. For this study a good and bad case machine is built up by hand winding to clarify the influence. To realize high quality measurements both machines use exactly the same rotor, about 60 thermocouples and a specific current measurement system in each parallel strand of one phase. It is shown that the measured losses differ for more than 3kW, meaning an additional loss amount of 65% at 11000 rpm. Looking at the measured currents the frequency dependency can be clearly seen. About three times higher current load in some strands is identified compared to ideal wire distribution. So overheating and possible cases of failure are possible. The measured data is used to validate a common analytical as well as a transient FEA model. While the FEA matches the measurement almost perfectly the analytical approach delivers some deviations, especially in bad case conditions. At the end an outlook regarding the temperature dependent loss scaling is given. Addicted to the ac loss amount different scaling behaviors occur.

[1]  Juha Pyrhonen,et al.  AC Resistance Factor in One-Layer Form-Wound Winding Used in Rotating Electrical Machines , 2013, IEEE Transactions on Magnetics.

[2]  Tong Lu.  Weiterentwicklung von hochtourigen permanenterregten Drehstromantrieben mit Hilfe von Finite-Elemente-Berechnungen und experimentellen Untersuchungen , 2004 .

[3]  Ulf Schwalbe,et al.  Effects of current displacement in a PMSM traction drive with single turn coils , 2013, 2013 International Electric Machines & Drives Conference.

[4]  Ayman M. El-Refaie,et al.  Fractional-Slot Concentrated-Windings Synchronous Permanent Magnet Machines: Opportunities and Challenges , 2010, IEEE Transactions on Industrial Electronics.

[5]  Ayman M. El-Refaie,et al.  Impact of Winding Layer Number and Slot/Pole Combination on AC Armature Losses of Synchronous Surface PM Machines Designed for Wide Constant-Power Speed Range Operation , 2008, 2008 IEEE Industry Applications Society Annual Meeting.

[6]  R. Wrobel,et al.  Investigation of Proximity Losses in a High Speed Brushless Permanent Magnet Motor , 2006, Conference Record of the 2006 IEEE Industry Applications Conference Forty-First IAS Annual Meeting.

[7]  R. Wrobel,et al.  Scaling of AC copper loss in thermal modeling of electrical machines , 2012, 2012 XXth International Conference on Electrical Machines.

[8]  David G. Dorrell,et al.  Skin effect and proximity losses in high speed brushless permanent magnet motors , 2013, 2013 IEEE Energy Conversion Congress and Exposition.

[9]  Ion Boldea,et al.  The Induction Machines Design Handbook, Second Edition , 2009 .

[10]  Jan A. Ferreira,et al.  Current Sharing Analysis of Parallel Strands in Low-Voltage High-Speed Machines , 2014, IEEE Transactions on Industrial Electronics.

[11]  R. Wrobel,et al.  Investigation of end-winding proximity losses in electromagnetic devices , 2010, The XIX International Conference on Electrical Machines - ICEM 2010.

[12]  Antonio Griffo,et al.  Derivation and Scaling of AC Copper Loss in Thermal Modeling of Electrical Machines , 2014, IEEE Transactions on Industrial Electronics.

[13]  P. L. Dowell,et al.  Effects of eddy currents in transformer windings , 1966 .

[14]  Ion Boldea,et al.  The Induction Machines Design Handbook , 2009 .

[15]  Henk Polinder,et al.  Stator winding proximity loss reduction techniques in high speed electrical machines , 2013, 2013 International Electric Machines & Drives Conference.

[16]  Duane C. Hanselman,et al.  Brushless Permanent-Magnet Motor Design , 1994 .

[17]  H. Polinder,et al.  Influence of PWM switching frequency on the losses in PM machines , 2014, 2014 International Conference on Electrical Machines (ICEM).

[18]  Phil Mellor,et al.  Influence of winding design on losses in brushless AC IPM propulsion motors , 2011, 2011 IEEE Energy Conversion Congress and Exposition.

[19]  Rafal Wrobel,et al.  Contribution of End-Winding Proximity Losses to Temperature Variation in Electromagnetic Devices , 2012, IEEE Transactions on Industrial Electronics.

[20]  D. Hawkins,et al.  Study of the thermal aspects in brushless permanent magnet machines performance , 2013, 2013 IEEE Workshop on Electrical Machines Design, Control and Diagnosis (WEMDCD).

[21]  F. Lee,et al.  Proximity effects in coils for high frequency power applications , 1992 .

[22]  Daniel M. Saban,et al.  Study of the Copper Losses in a High-Speed Permanent-Magnet Machine With Form-Wound Windings , 2014, IEEE Transactions on Industrial Electronics.

[23]  Rik W. De Doncker,et al.  Eddy currents in windings of switched reluctance machines , 2008 .

[24]  Charles R. Sullivan.  Optimal choice for number of strands in a litz-wire transformer winding , 1997 .