Electromagnetic-thermal coupling behaviors and thermal convection during two-phase zone continuous casting high strength aluminum alloy tube

[1]  S. S. Wang,et al.  Thermal characteristics of induction heating with stepped diameter mold during two-phase zone continuous casting high-strength aluminum alloys , 2020 .

[2]  Ruirun Chen,et al.  A novel method to prepare columnar grains of TiAl alloys by controlling induction heating , 2019, International Communications in Heat and Mass Transfer.

[3]  J. Smolka,et al.  Numerical examination of the evaporation process within a vacuum induction furnace with a comparison to experimental results , 2019, Applied Thermal Engineering.

[4]  C. Blanc,et al.  Influence of hydrogen on the propagation of intergranular corrosion defects in 2024 aluminium alloy , 2019, Corrosion Science.

[5]  Zhifeng Zhang,et al.  Numerical modeling of annular electromagnetic stirring with intercooling in direct chill casting of 7005 aluminum alloy billet , 2019, Progress in Natural Science: Materials International.

[6]  Ruirun Chen,et al.  Numerical analysis for electromagnetic field influence on heat transfer behaviors in cold crucible used for directional solidification , 2018, International Journal of Heat and Mass Transfer.

[7]  Zhiming Gao,et al.  Numerical simulation for macrosegregation in direct-chill casting of 2024 aluminum alloy with an extended continuum mixture model , 2018 .

[8]  S. Xiong,et al.  Determination of the interfacial heat transfer coefficient at the metal-sand mold interface in low pressure sand casting , 2017 .

[9]  J. Sieniawski,et al.  Investigation of casting–ceramic shell mold interface thermal resistance during solidification process of nickel based superalloy , 2017 .

[10]  Shao-ming Zhang,et al.  Numerical study of titanium melting by high frequency inductive heating , 2017 .

[11]  P. Rattanadecho,et al.  Effect of electromagnetic field on distribution of temperature, velocity and concentration during saturated flow in porous media based on Local Thermal Non-Equilibrium models (influent of input power and input velocity) , 2017 .

[12]  Han Yi,et al.  Study on mobile induction heating process of internal gear rings for wind power generation , 2017 .

[13]  Prodyut R. Chakraborty.  Enthalpy porosity model for melting and solidification of pure-substances with large difference in phase specific heats , 2017 .

[14]  Young Hoon Moon,et al.  Coupled electromagnetic and thermal analysis of induction heating for the forging of marine crankshafts , 2016 .

[15]  L. Begum,et al.  A computational study of low-head direct chill slab casting of aluminum alloy AA2024 , 2016 .

[16]  M. Malekan,et al.  Effect of cooling rate on the solidification characteristics and dendrite coherency point of ADC12 aluminum die casting alloy using thermal analysis , 2016, Journal of Thermal Analysis and Calorimetry.

[17]  Xuefeng Liu,et al.  Surface quality, microstructure and mechanical properties of Cu–Sn alloy plate prepared by two-phase zone continuous casting , 2015 .

[18]  A. Phillion,et al.  Microstructure, Macrosegregation, and Thermal Analysis of Direct Chill Cast AA5182 Aluminum Alloy , 2015, Journal of Materials Engineering and Performance.

[19]  S. Shabestari,et al.  Effect of Cooling Rate on the Dendrite Coherency Point During Solidification of Al2024 Alloy , 2015, Metallurgical and Materials Transactions A.

[20]  S. Shabestari,et al.  Evaluation of formation of intermetallic compounds in Al2024 alloy using thermal analysis technique , 2014 .

[21]  Constantinos Soutis,et al.  Recent developments in advanced aircraft aluminium alloys , 2014 .

[22]  M. Okayasu,et al.  Microstructure and material properties of an Al–Cu alloy provided by the Ohno continuous casting technique , 2010 .

[23]  M. Okayasu,et al.  Mechanical properties of Al-Si13-Ni1.4-Mg1.4-Cu1 alloys produced by the Ohno continuous casting process , 2010 .

[24]  C. Mapelli,et al.  Application of electromagnetic stirring for the homogenization of aluminium billet cast in a semi-continuous machine , 2010 .

[25]  Huixue Jiang,et al.  Rapid air film continuous casting of aluminum alloy using static magnetic field , 2009 .

[26]  J. Cui,et al.  Experimental investigation of heat transport and solidification during low frequency electromagnetic hot-top casting of 6063 aluminum alloy , 2008 .

[27]  L. Katgerman,et al.  Macrosegregation in direct-chill casting of aluminium alloys , 2008 .

[28]  L. Katgerman,et al.  Modeling Macrosegregation during Direct-Chill Casting of Multicomponent Aluminum Alloys , 2007 .

[29]  F. Incropera,et al.  The effect of free-floating dendrites and convection on macrosegregation in direct chill cast aluminum alloys. Part II : predictions for Al-Cu and Al-Mg alloys , 2000 .

[30]  A. V. Reddy,et al.  Modeling of macrosegregation due to thermosolutal convection and contraction-driven flow in direct chill continuous casting of an Al-Cu round ingot , 1997 .

[31]  Yaohua Yang,et al.  Thermal characteristics and uniformity of microstructures during temperature controlled mold continuous casting profiled copper alloy strip , 2020 .

[32]  Ruirun Chen,et al.  Dominant dimensionless parameters controlling solute transfer during electromagnetic cold crucible melting and directional solidifying TiAl alloys , 2018 .