Fabrication, characterization and analysis of improvements in mechanical properties of AA7075/ZrB2 in-situ composites

Abstract In this research work, AA7075/xZrB2 [x = 0, 3, 6 and 9 volume fraction] in-situ composites have been fabricated by exothermic chemical reactions between the inorganic salts K2ZrF6 and KBF4 with aluminum melt at 900 °C. The fabricated composites were characterized using Optical Microscope (OM), Field Emission Scanning Electron Microscope (FESEM) and Transmission Electron Microscope (TEM). The microhardness, yield strength and ultimate tensile strength (UTS) were evaluated. Energy Dispersive Spectroscopy (EDS) and X-ray Diffraction (XRD) depict the presence of ZrB2 particles in the matrix without formation of any other inter-metallic compounds. The fabricated castings with 30 min holding time of melt were characterized with FESEM and the mechanical properties were evaluated and compared with the results of fabricated castings with 60 min holding time of melt. The size of ZrB2 particles formed in the Aluminum Matrix Composites (AMCs) was found from 2 to 9 µm with different shapes like cubic and pyramid. The reduction in grain size of Al-rich phase of the AMCs was observed from TEM. The improvements on mechanical properties have been found with successive added volume fraction of ZrB2 particles in AMCs with 60 min holding time of melt. The effect of strengthening mechanisms on yield strength was calculated experimentally and theoretically and its results were tabulated.

[1]  S. Guo,et al.  Densification of ZrB2-based composites and their mechanical and physical properties: A review , 2009 .

[2]  I. Dinaharan,et al.  Microstructure and mechanical behavior of AA2024 aluminum matrix composites reinforced with in situ synthesized ZrB2 particles , 2018 .

[3]  S. Sivasankaran,et al.  Microstructure, cold workability and strain hardening behavior of trimodaled AA 6061–TiO2 nanocomposite prepared by mechanical alloying , 2011 .

[4]  M. Gupta,et al.  Structural and mechanical properties of Ni60Nb40 amorphous alloy particle reinforced Al-based composites produced by microwave-assisted rapid sintering , 2013 .

[5]  K. Sivaprasad,et al.  Dry sliding wear behaviour of AA 6351-ZrB2 in situ composite at room temperature , 2010 .

[6]  Gao-hui Wu,et al.  Property Characteristics of a TiB2P/Al Composite Fabricatedby Squeeze Casting Technology , 2003 .

[7]  S. Sajjadi,et al.  Comparison of microstructure and mechanical properties of A356 aluminum alloy/Al2O3 composites fabricated by stir and compo-casting processes , 2012 .

[8]  I. Dinaharan,et al.  Synthesis and characterization of in situ formed titanium diboride particulate reinforced AA7075 aluminum alloy cast composites , 2013 .

[9]  Şener Karabulut,et al.  Optimization of surface roughness and cutting force during AA7039/Al2O3 metal matrix composites milling using neural networks and Taguchi method , 2015 .

[10]  Huijun Kang,et al.  Development of TiB2 reinforced aluminum foundry alloy based in situ composites – Part II: Enhancing the practical aluminum foundry alloys using the improved Al–5 wt%TiB2 master composite upon dilution , 2014 .

[11]  G. Sun,et al.  In situ synthesis of novel composites in the system Al-Zr-O , 2001 .

[12]  Jiecai Han,et al.  Preparation, microstructure and mechanical properties of ZrB2–ZrO2 ceramics , 2009 .

[13]  K. Sivaprasad,et al.  Study on abrasive and erosive wear behaviour of Al 6063/TiB2 in situ composites , 2008 .

[14]  I. Dinaharan,et al.  Influence of friction stir processing on microstructure and properties of AA7075/TiB2 in situ composite , 2016 .

[15]  Zhenya Zhang,et al.  Effects of in situ generated ZrB2 nano-particles on microstructure and tensile properties of 2024Al matrix composites , 2014 .

[16]  K. Palanikumar,et al.  Experimental investigation and analysis of thrust force in drilling cast hybrid metal matrix (Al–15%SiC–4%graphite) composites , 2014 .

[17]  M. Martínez,et al.  Optimization of processing parameters for the Al + 10% B4C system obtained by mechanical alloying , 2007 .

[18]  R. Keshavamurthy,et al.  Microstructure and mechanical behaviour of in situ fabricated AA6061–TiC metal matrix composites , 2017 .

[19]  Rafiuddin,et al.  Preparation, characterization, electrical conductivity and dielectric studies of Na2SO4 and V2O5 composite solid electrolytes , 2016 .

[20]  I. Dinaharan,et al.  Influence of in situ formed ZrB2 particles on microstructure and mechanical properties of AA6061 metal matrix composites , 2011 .

[21]  G. Gautam,et al.  Effect of ZrB2 particles on the microstructure and mechanical properties of hybrid (ZrB2 + Al3Zr)/AA5052 insitu composites , 2015 .

[22]  Gang Chen,et al.  Microstructure and mechanical properties of in situ TiB2/7055 composites synthesized by direct magnetochemistry melt reaction , 2013 .

[23]  Jun Wang,et al.  Effects of CeO2 additive on the microstructure and mechanical properties of in situ TiB2/Al composite , 2011 .

[24]  P. Lakshminarayanan,et al.  Dry sliding wear behaviour of in situ Al–TiB2 composites , 2013 .

[25]  S. Baskaran,et al.  Investigations on dry sliding wear behavior of in situ casted AA7075–TiC metal matrix composites by using Taguchi technique , 2014 .

[26]  M. Rahimian,et al.  The effect of production parameters on microstructure and wear resistance of powder metallurgy Al–Al2O3 composite , 2011 .

[27]  Z. Chen,et al.  Microstructure and properties of In situ Al/TiB2 composite fabricated by in-melt reaction method , 2000 .

[28]  Narendra Kumar,et al.  In-situ development of ZrB2 particles and their effect on microstructure and mechanical properties of AA5052 metal-matrix composites , 2015 .

[29]  Z. Zhang,et al.  Consideration of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites: A model for predicting their yield strength , 2006 .

[30]  Gang Chen,et al.  Microstructures and dry sliding wear properties of in situ (Al3Zr + ZrB2)/Al composites , 2007 .

[31]  Gang Chen,et al.  (ZrB2 + Al2O3 + Al3Zr)p/Al–4Cu composite synthesized by magneto-chemical melt reaction , 2008 .

[32]  J. Selvam,et al.  Turning characteristics of in situ formed TiB2 ceramic particulate reinforced AA7075 aluminum matrix composites using polycrystalline diamond cutting tool , 2018, Measurement.

[33]  S. N. Ojha,et al.  Microstructure and electrical conductivity of Al-SiCp composites produced by spray forming process , 2005 .