Chatter stability of milling with speed-varying dynamics of spindles

Abstract The chatter stability of machine tool is dependent on the dynamic behavior of the spindle system, which is often expressed as the frequency response function (FRF) at the tool tip. The stability lobe diagram generated from stationary FRFs can lead to an inaccurate prediction in high and ultra high speed machining. This paper presents an alternative approach to predict the chatter stability lobes of high-speed milling with consideration of speed-varying spindle dynamics. With a dynamic model of a high-speed spindle system, the speed effects (i.e., gyroscopic moment and centrifugal forces) on both the spindle shaft and bearings are investigated systematically with simulations and experiments. The gyroscopic moment of the spindle shaft can increase the cross FRFs, but can hardly affect the direct FRFs at the tool tip due to the damping of the spindle system. The centrifugal forces on both the shaft and bearings lower the overall spindle system stiffness evidently as the speed increases. The speed-dependent FRFs at the tool tip are obtained from the dynamic spindle model and then integrated into the characteristic equation of the dynamic milling system. Nyquist stability criterion is used to generate the chatter stability lobe of high-speed milling operations. It is shown that the stability lobes with speed effects shift to the low speed range significantly. Finally, milling tests are performed to validate predicted the speed-dependent stability lobe.

[1]  R. Sridhar,et al.  A Stability Algorithm for the General Milling Process: Contribution to Machine Tool Chatter Research—7 , 1968 .

[2]  Jifang Tian,et al.  Chatter Instability in Milling Systems with Flexible Rotating Spindles—A New Theoretical Approach , 2001 .

[3]  David J. Ewins,et al.  Modal Testing: Theory, Practice, And Application , 2000 .

[4]  Pascal Ray,et al.  Stability-Based Spindle Design Optimization , 2007 .

[5]  Mohammad R. Movahhedy,et al.  Prediction of chatter in high speed milling including gyroscopic effects , 2006 .

[6]  Kon Well Wang,et al.  An Integrated Approach Toward the Dynamic Analysis of High-Speed Spindles: Part 2—Dynamics Under Moving End Load , 1993 .

[7]  Eberhard Abele,et al.  Creating Stability Lobe Diagrams during Milling , 2004 .

[8]  Victor Songmene,et al.  Estimation of machine-tool dynamic parameters during machining operation through operational modal analysis , 2009 .

[9]  A. B. Jones.  A General Theory for Elastically Constrained Ball and Radial Roller Bearings Under Arbitrary Load and Speed Conditions , 1960 .

[10]  Hongqi Li,et al.  Integrated Dynamic Thermo-Mechanical Modeling of High Speed Spindles, Part 2: Solution Procedure and Validations , 2004 .

[11]  Henk Nijmeijer,et al.  Prediction of regenerative chatter by modelling and analysis of high-speed milling , 2003 .

[12]  Tony L. Schmitz,et al.  Improving High-Speed Machining Material Removal Rates by Rapid Dynamic Analysis , 2001 .

[13]  S. A. Tobias.  Machine-tool vibration , 1965 .

[14]  Yusuf Altintas,et al.  A General Method for the Modeling of Spindle-Bearing Systems , 2004 .

[15]  Ioannis Minis,et al.  Analysis of Linear and Nonlinear Chatter in Milling , 1990 .

[16]  T. A. Harris,et al.  Rolling Bearing Analysis , 1967 .

[17]  Yung C. Shin,et al.  Bearing Nonlinearity and Stability Analysis in High Speed Machining , 1992 .

[18]  Tony L. Schmitz,et al.  ROTATING TOOL POINT FREQUENCY RESPONSE PREDICTION USING RCSA , 2007 .

[19]  Yusuf Altintas,et al.  Analytical Prediction of Stability Lobes in Milling , 1995 .

[20]  Gábor Stépán,et al.  Stability of up-milling and down-milling, part 1: alternative analytical methods , 2003 .

[21]  Yusuf Altintas,et al.  Modeling of spindle-bearing and machine tool systems for virtual simulation of milling operations , 2007 .

[22]  Yusuf Altintas,et al.  Manufacturing Automation: Metal Cutting Mechanics, Machine Tool Vibrations, and CNC Design , 2000 .