A custom-designed limited-angle actuator for an electromechanical engine valve drive Part II: Fabrication and evaluation

Research has shown that variable valve timing (WT) can improve significantly the performance of internal combustion (IC) engines, including higher fuel efficiencies, lower emissions, and larger torque outputs at each point of the engine map. To achieve independent and continuous WT for each valve, an electromechanical valve drive (EMV) system with a custom-designed limited-angle actuator was proposed previously, whose feasibility with lower power consumption, smaller package, and faster transition was predicted by simulation. In order to validate the concept experimentally, a prototype actuator was built and evaluated in this paper. The fabrication considerations and assembling process of the prototype actuator are discussed before satisfactory experimental results of the whole EMV system with the prototype actuator are presented. A further projection for a full engine valve actuation illustrates a promising future of the EMV system with the limited-angle actuator in a real engine environment up to an engine speed of 6000 rpm. (6 pages)

[1]  R. Flierl,et al.  The Third Generation of Valvetrains - New Fully Variable Valvetrains for Throttle-Free Load Control , 2000 .

[2]  D.J. Perreault,et al.  Design and experimental evaluation of an electromechanical engine valve drive , 2004, 2004 IEEE 35th Annual Power Electronics Specialists Conference (IEEE Cat. No.04CH37551).

[3]  Ingo Lenz,et al.  A Fully Continuous Variable Cam Timing Concept for Intake and Exhaust Phasing , 1998 .

[4]  Anna G. Stefanopoulou,et al.  Rendering the electromechanical valve actuator globally asymptotically stable , 2003, 42nd IEEE International Conference on Decision and Control (IEEE Cat. No.03CH37475).

[5]  Eric Rask,et al.  Two-Step Variable Valve Actuation for Fuel Economy, Emissions, and Performance , 2003 .

[6]  Achim Koch,et al.  Sensorless Control of Electromagnetic Actuators for Variable Valve Train , 2000 .

[7]  Woo Sok Chang,et al.  An electromechanical valve drive incorporating a nonlinear mechanical transformer , 2003 .

[8]  Thomas Dresner,et al.  A Review of Variable Valve Timing Benefits and Modes of Operation , 1989 .

[9]  V. Picron,et al.  Electro-Magnetic Valve Actuation System: First Steps toward Mass Production , 2008 .

[10]  Yan Wang,et al.  Nonlinear Self-Tuning Control for Soft Landing of an Electromechanical Valve Actuator , 2002 .

[11]  Martin Pischinger,et al.  Benefits of the Electromechanical Valve Train in Vehicle Operation , 2000 .

[12]  G. B. Parvate-Patil,et al.  An Assessment of Intake and Exhaust Philosophies for Variable Valve Timing , 2003 .

[13]  Michael Levin,et al.  Increasing Torque Output from a Turbodiesel with Camless Valvetrain , 2002 .

[14]  T. Ahmad,et al.  A Survey of Variable-Valve-Actuation Technology , 1989 .

[15]  Yihui Qiu,et al.  Advanced modeling ,control, and design of an electromechanical engine value drive system with a limited-angle actuator , 2009 .

[16]  Tushar Anil Parlikar.  Experimental implementation of an electromagnetic engine valve , 2003 .

[17]  T.A. Parlikar,et al.  Design and experimental implementation of an electromagnetic engine valve drive , 2005, IEEE/ASME Transactions on Mechatronics.

[18]  David J. Perreault,et al.  Optimal cam design and system control for an electromechanical engine valve drive , 2010, 2010 IEEE International Conference on Industrial Technology.