Fabrication and characterization of MEMS-based PZT/PZT bimorph thick film vibration energy harvesters

We describe the fabrication and characterization of a significantly improved version of a microelectromechanical system-based PZT/PZT thick film bimorph vibration energy harvester with an integrated silicon proof mass; the harvester is fabricated in a fully monolithic process. The main advantage of bimorph vibration energy harvesters is that strain energy is not lost in mechanical support materials since only Pb(ZrxTi1-x)O3 (PZT) is strained; as a result, the effective system coupling coefficient is increased, and thus a potential for significantly higher output power is released. In addition, when the two layers are connected in series, the output voltage is increased, and as a result the relative power loss in the necessary rectifying circuit is reduced. We describe an improved process scheme for the energy harvester, which resulted in a robust fabrication process with a record high fabrication yield of 98%. The robust fabrication process allowed a high pressure treatment of the screen printed PZT thick films prior to sintering. The high pressure treatment improved the PZT thick film performance and increased the harvester power output to 37.1 ?W at 1 g root mean square acceleration. We also characterize the harvester performance when only one of the PZT layers is used while the other is left open or short circuit.

[1]  E. Thomsen,et al.  Advantages of PZT thick film for MEMS sensors , 2010 .

[2]  Paul K. Wright,et al.  A piezoelectric vibration based generator for wireless electronics , 2004 .

[3]  Lu Dong,et al.  Fabrication and performance of MEMS-based piezoelectric power generator for vibration energy harvesting , 2006, Microelectron. J..

[4]  K. Najafi,et al.  MULTI-LAYER PZT STACKING PROCESS FOR PIEZOELECTRIC BIMORPH ENERGY HARVESTERS , 2011 .

[5]  Sang-Gook Kim,et al.  Energy harvesting MEMS device based on thin film piezoelectric cantilevers , 2006 .

[6]  S. Beeby,et al.  Energy harvesting vibration sources for microsystems applications , 2006 .

[7]  M. Roukes,et al.  Thermoelastic damping in micro- and nanomechanical systems , 1999, cond-mat/9909271.

[8]  H. Wikle,et al.  The design, fabrication and evaluation of a MEMS PZT cantilever with an integrated Si proof mass for vibration energy harvesting , 2008 .

[9]  E. Thomsen,et al.  MEMS-based thick film PZT vibrational energy harvester , 2011, 2011 IEEE 24th International Conference on Micro Electro Mechanical Systems.

[10]  W. Zaki.  An approach to modeling tensile–compressive asymmetry for martensitic shape memory alloys , 2010 .

[11]  O. Hansen,et al.  Screen printed PZT/PZT thick film bimorph MEMS cantilever device for vibration energy harvesting , 2011, 2011 16th International Solid-State Sensors, Actuators and Microsystems Conference.

[12]  Neil M. White,et al.  Fabrication and characterization of free-standing thick-film piezoelectric cantilevers for energy harvesting , 2009 .

[13]  N. Hudak,et al.  Small-scale energy harvesting through thermoelectric, vibration, and radiofrequency power conversion , 2008 .

[14]  Daniel J. Inman,et al.  An experimentally validated bimorph cantilever model for piezoelectric energy harvesting from base excitations , 2009 .

[15]  K. Najafi,et al.  Thinned-PZT on SOI process and design optimization for piezoelectric inertial energy harvesting , 2011, 2011 16th International Solid-State Sensors, Actuators and Microsystems Conference.

[16]  Y. V. Andel,et al.  Vibration energy harvesting with aluminum nitride-based piezoelectric devices , 2009 .

[17]  Nesbitt W. Hagood,et al.  Damping of structural vibrations with piezoelectric materials and passive electrical networks , 1991 .