Spatial Distribution Evolution of Residual Stress and Microstructure in Laser-Peen-Formed Plates

Residual stress in structural components is crucial as it affects both service performance and safety. To investigate the evolution of residual stress in a laser-peen-formed panel, this study adopted two plate samples of thickness 3 and 9 mm instead of the conventional Almen strip. The two plates were peened with an identical energy density of 10.99 GW/cm2. The residual stress across the entire section was determined using a slitting method, and near-surface stress was then verified by X-ray diffraction. Furthermore, cross-sectional variation in hardness and microstructure were characterized to understand the residual stress evolution. The experimental results showed that different thicknesses resulted in distinct spatial distributions of residual stress. The 3-mm plate demonstrated a shallow (0.5 mm) and lower compressive stress magnitude (−270 MPa) compared with a deeper (1 mm) and higher compressive stress (−490 MPa) in the 9-mm plate. Further analysis revealed that the deformation compatibility during the forming process inevitably leads to a stress compensation effect on the peened side. The decrease in the depth and magnitude of the compressive residual stress in the thin plate was mainly attributed to low stiffness and large deflection.

[1]  A. Clauer.  Laser Shock Peening, the Path to Production , 2019, Metals.

[2]  M. Fitzpatrick,et al.  Effect of alloy temper on surface modification of aluminium 2624 by laser shock peening , 2018, Surface and Coatings Technology.

[3]  B. Klusemann,et al.  Experimental and numerical investigation of residual stresses in laser shock peened AA2198 , 2018 .

[4]  J. Ocaña,et al.  Laser Shock Processing of thin Al2024-T351 plates for induction of through-thickness compressive residual stresses fields , 2015 .

[5]  M. Preuss,et al.  Evolution of a laser shock peened residual stress field locally with foreign object damage and subsequent fatigue crack growth , 2015 .

[6]  R. V. Martinez,et al.  Large-scale nanoshaping of ultrasmooth 3D crystalline metallic structures , 2014, Science.

[7]  Mamoun Medraj,et al.  Laser Peening Process and Its Impact on Materials Properties in Comparison with Shot Peening and Ultrasonic Impact Peening , 2014, Materials.

[8]  M. Hill.  The Slitting Method , 2013 .

[9]  C. Perron,et al.  On the effect of the orientation of sheet rolling direction in shot peen forming , 2013 .

[10]  Steven E. Olson,et al.  Prediction and characterization of residual stresses from laser shock peening , 2012 .

[11]  P. K. Jena,et al.  Effect of heat treatment on the behavior of an AA7055 aluminum alloy during ballistic impact , 2011 .

[12]  Martin Lévesque,et al.  Experimental study of shot peening and stress peen forming , 2010 .

[13]  Zhenqiang Yao,et al.  Laser peen forming induced two way bending of thin sheet metals and its mechanisms , 2010 .

[14]  Gary J. Cheng,et al.  Microstructure and mechanical property characterizations of metal foil after microscale laser dynamic forming , 2007 .

[15]  Y. Mai,et al.  Laser shock processing and its effects on microstructure and properties of metal alloys: a review , 2002 .

[16]  Michael R. Hill,et al.  Residual stress, stress relief, and inhomogeneity in aluminum plate , 2002 .

[17]  Michael B. Prime,et al.  Residual Stress Measurement by Successive Extension of a Slot: The Crack Compliance Method , 1999 .

[18]  Lloyd A. Hackel,et al.  High Power Laser for Peening of Metals Enabling Production Technology , 1998 .

[19]  Allan H. Clauer,et al.  Laser Shock Processing Increases the Fatigue Life of Metal Parts , 1991 .

[20]  S. BRODETSKY,et al.  Theory of Plates and Shells , 1941, Nature.

[21]  M. Fitzpatrick,et al.  Effect of texture on the residual stress response from laser peening of an aluminium-lithium alloy , 2018 .

[22]  Z. Yao,et al.  Geometry distortion and residual stress of alternate double-sided laser peening of thin section component , 2018 .