Performance Improvement of IPMC (Ionic Polymer Metal Composites) for a Flapping Actuator

In this paper, a trade-off design and fabrication of IPMC (Ionic Polymer Metal Composites) as an actuator for a flapping device have been described. Experiments for the internal solvent loss of IPMCs have been conducted for various combinations of cation and solvent in order to find out the best combination of cation and solvent for minimal solvent loss and higher actuation force. From the experiments, it was found that IPMCs with heavy water as their solvent could operate longer. Relations between length/thickness and tip force of IPMCs were also quantitatively identified for the actuator design from the tip force measurement of 200, 400, 640, and 800µm thick IPMCs. All IPMCs thicker than 200µm were processed by casting Nafion™ solution. The shorter and thicker IPMCs tended to generate higher actuation force but lower actuation displacement. To improve surface conductivity and to minimize solvent evaporation due to electrically heated electrodes, gold was sputtered on both surfaces of the cast IPMCs by the Physical Vapor Deposition (PVD) process. For amplification of a short IPMC's small actuation displacement to a large flapping motion, a rack-and-pinion type hinge was used in the flapping device. An insect wing was attached to the IPMC flapping mechanism for its flapping test. In this test, the wing flapping device using the 800µm thick IPMC could create around 10°~85° flapping angles and 0.5~15Hz flapping frequencies by applying 3~4V.

[1]  Byungkyu Kim,et al.  Analysis of mechanical characteristics of the ionic polymer metal composite (IPMC) actuator using cast ion-exchange film , 2003, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[2]  K. Oguro,et al.  Effect on bending behavior of counter cation species in perfluorinated sulfonate membrane–platinum composite , 1998 .

[3]  S. Nemat-Nasser,et al.  Comparative experimental study of ionic polymer–metal composites with different backbone ionomers and in various cation forms , 2003 .

[4]  D. Leo,et al.  Ionic liquids as stable solvents for ionic polymer transducers , 2004 .

[5]  S. Srinivasan,et al.  A comparison of physical properties and fuel cell performance of Nafion and zirconium phosphate/Nafion composite membranes , 2003, physics/0310029.

[6]  Kinji Asaka,et al.  Bending of polyelectrolyte membrane platinum composites by electric stimuli. Part II. Response kinetics , 2000 .

[7]  H. Yeager,et al.  Perfluorinated Ionomer Membranes , 1982 .

[8]  M. Shahinpoor Continuum electromechanics of ionic polymeric gels as artificial muscles for robotic applications , 1994 .

[9]  Keisuke Oguro,et al.  Biomimetic microactuators based on polymer electrolyte/gold composite driven by low voltage , 2000, Proceedings IEEE Thirteenth Annual International Conference on Micro Electro Mechanical Systems (Cat. No.00CH36308).

[10]  Fabrication Process and Characterization of Sonic Polymer-Metal Composite Actuators by Electroless Plating of Platinum , 2002 .

[11]  K. Kim,et al.  Ionic polymer–metal composites: II. Manufacturing techniques , 2003 .

[12]  Kinji Asaka,et al.  The effects of counter ions on characterization and performance of a solid polymer electrolyte actuator , 2001 .

[13]  Yoseph Bar-Cohen,et al.  Electroactive Polymer (EAP) Actuators as Artificial Muscles: Reality, Potential, and Challenges, Second Edition , 2004 .

[14]  Kyoung Kwan Ahn,et al.  Position Control of Shape Memory Alloy Actuators by Using Self Tuning Fuzzy PID Controller , 2006, 2006 1ST IEEE Conference on Industrial Electronics and Applications.

[15]  Toshi Takamori,et al.  3-dimensional dynamic model of ionic conducting polymer gel film (ICPF) actuator , 1996, 1996 IEEE International Conference on Systems, Man and Cybernetics. Information Intelligence and Systems (Cat. No.96CH35929).

[16]  J. Leddy,et al.  Density and solubility of nafion:  recast, annealed, and commercial films. , 1996, Analytical chemistry.

[17]  K. Oguro,et al.  Bending of Polyelectrolyte Membrane–Platinum Composites by Electric Stimuli I. Response Characteristics to Various Waveforms , 1995 .

[18]  T. Gierke,et al.  The Cluster—Network Model of Ion Clustering in Perfluorosulfonated Membranes , 1982 .

[19]  T. Gierke,et al.  Ion transport and clustering in nafion perfluorinated membranes , 1983 .

[20]  K. Kim,et al.  Ionic polymer-metal composites: I. Fundamentals , 2001 .

[21]  J. Mahan Physical Vapor Deposition of Thin Films , 2000 .

[22]  Mohsen Shahinpoor,et al.  Ion-exchange-metal composite artificial muscle actuator load characterization and modeling , 1997, Smart Structures.