Design of new three-line balun and its implementation using multilayer configuration

This paper proposes a new balun that is composed of three coupled quarter-wavelength lines. The proposed balun is optimized by using design of experiments to achieve a maximum bandwidth. After the optimization, it is transformed into the balun consisting of a pair of coupled quarter-wavelength lines in connection with an uncoupled quarter-wavelength line. The design method and its implemented results using a multilayer configuration are presented. It is shown that this new balun can be made more compact, providing good performances over the wide frequency range. Therefore, the balun developed here is applicable to many wireless and mobile communication systems. The design equation for a given set of balun impedances at unbalanced and balanced ports is derived from an equivalent circuit of the proposed balun. To demonstrate the feasibility and validity of the design equation, the size 2012 multilayer ceramic chip baluns with three different balun impedances, which operated in the 2.4-GHz industrial-scientific-medical band frequency, are designed and fabricated by the use of low-temperature co-fired ceramic technology. According to the measured results, the maximum insertion loss is 0.81 dB, the maximum in-band phase imbalance is within 7/spl deg/, and the maximum in-band amplitude imbalance is less than 0.7 dB.

[1]  D. Staiculescu,et al.  Design and optimization of 3-D compact stripline and microstrip Bluetooth/WLAN balun architectures using the design of experiments technique , 2005, IEEE Transactions on Antennas and Propagation.

[2]  Chi-Yang Chang,et al.  A semi-lumped balun fabricated by low temperature co-fired ceramic , 2002, 2002 IEEE MTT-S International Microwave Symposium Digest (Cat. No.02CH37278).

[3]  Kenjiro Nishikawa,et al.  Compact and broad-band three-dimensional MMIC balun , 1999 .

[4]  D. Kossives,et al.  Design and characterization of multilayer spiral transmission-line baluns , 1999 .

[5]  G.R. Branner,et al.  Optimized design of unique miniaturized planar baluns for wireless applications , 2003, IEEE Microwave and Wireless Components Letters.

[6]  K. C. Gupta,et al.  CAD procedures for planar re-entrant type couplers and three-line baluns , 1993, 1993 IEEE MTT-S International Microwave Symposium Digest.

[7]  Ichihiko Toyoda,et al.  Three-dimensional MMIC and its application: an ultra-wideband miniature balun , 1995 .

[8]  T. Morikawa,et al.  Chip type spiral broadside coupled directional couplers and baluns using low temperature co-fired ceramic , 1999, 1999 Proceedings. 49th Electronic Components and Technology Conference (Cat. No.99CH36299).

[9]  M. C. Tsai.  A new compact wideband balun , 1993, IEEE 1993 Microwave and Millimeter-Wave Monolithic Circuits Symposium Digest of Papers.

[10]  Henry Jasik,et al.  Antenna engineering handbook , 1961 .

[11]  Chi-Yang Chang,et al.  Using buried capacitor in LTCC-MLC balun , 2002 .

[12]  Kuldip Gupta,et al.  A new design procedure for single-layer and two-layer three-line baluns , 1998, IMS 1998.

[13]  Dal Ahn,et al.  A design of the ceramic chip balun using the multilayer configuration , 2001 .

[14]  Jae Yeong Park,et al.  A miniaturized LTCC multi-layered front-end module for dual band WLAN (802.11 a/b/g) applications , 2004, 2004 IEEE MTT-S International Microwave Symposium Digest (IEEE Cat. No.04CH37535).

[15]  Ian D. Robertson,et al.  Analysis and design of impedance-transforming planar Marchand baluns , 2001 .

[16]  D. Pozar.  Microwave Engineering , 1990 .

[17]  Kian Sen Ang,et al.  Analysis and design of miniaturized lumped-distributed impedance-transforming baluns , 2003 .

[18]  Chi-Yang Chang,et al.  Chip-type LTCC-MLC baluns using the stepped impedance method , 2001 .

[19]  Kian Sen Ang,et al.  Multisection impedance-transforming coupled-line baluns , 2003 .

[20]  I.D. Robertson,et al.  On miniaturization isolation network of an all-ports matched impedance-transforming Marchand Balun , 2003, IEEE Microwave and Wireless Components Letters.

[21]  D. Kammler.  Calculation of Characteristic Admittances and Coupling Coefficients for Strip Transmission Lines , 1968 .

[22]  I. Gavela,et al.  A small size LTCC balun for wireless applications , 2004, 34th European Microwave Conference, 2004..

[23]  R. A. Johnson,et al.  Antenna engineering handbook /2nd edition/ , 1984 .

[24]  Cheng-Yuan Tang,et al.  LTCC-MLC chip-type balun realised by LC resonance method , 2002 .