Characteristics of subzero startup and water/ice formation on the catalyst layer in a polymer electrolyte fuel cell

Abstract This work experimentally explores the fundamental characteristics of a polymer electrolyte fuel cell (PEFC) during subzero startup, which encompasses gas purge, cool down, startup from a subfreezing temperature, and finally warm up. In addition to the temperature, high-frequency resistance (HFR) and voltage measurements, direct observations of water or ice formation on the catalyst layer (CL) surface have been carried out for the key steps of cold start using carbon paper punched with microholes and a transparent cell fixture. It is found that purge time significantly influences water content of the membrane after purge and subsequently cold-start performance. Gas purge for less than 30 s appears to be insufficient, and that between 90 and 120 s is most useful. After gas purge, however, the cell HFR relaxation occurs for longer than 30 min due to water redistribution in the membrane-electrode assembly (MEA). Cold-start performance following gas purge and cool down strongly depends on the purge time and startup temperature. The cumulative product water measuring the isothermal cold-start performance increases dramatically with the startup temperature. The state of water on the CL surface has been studied during startup from ambient temperatures ranging from −20 to −1 °C. It is found that the freezing-point depression of water in the cathode CL is 1.0 ± 0.5 °C and its effect on PEFC cold start under automotive conditions is negligible.

[1]  Shimshon Gottesfeld,et al.  Low platinum loading electrodes for polymer electrolyte fuel cells fabricated using thermoplastic ionomers , 1995 .

[2]  Chao-Yang Wang,et al.  Analysis of Cold Start in Polymer Electrolyte Fuel Cells , 2007 .

[3]  Kazuhiko Yoshida,et al.  Behavior of water below the freezing point in PEFCs , 2007 .

[4]  R. C. Weast.  CRC Handbook of Chemistry and Physics , 1973 .

[5]  G. G. Stokes.  "J." , 1890, The New Yale Book of Quotations.

[6]  I. Hsing,et al.  Absorption, Desorption, and Transport of Water in Polymer Electrolyte Membranes for Fuel Cells , 2005 .

[7]  Hyunchul Ju,et al.  Nonisothermal Modeling of Polymer Electrolyte Fuel Cells I. Experimental Validation , 2005 .

[8]  B. Wetton,et al.  Water Management in PEM Fuel Cells , 2004 .

[9]  Qunhui Guo,et al.  Effect of freeze-thaw cycles on the properties and performance of membrane-electrode assemblies , 2006 .

[10]  Dirk Riemann,et al.  Low temperature operation and influence parameters on the cold start ability of portable PEMFCs , 2006 .

[11]  Chao-Yang Wang,et al.  Fundamental models for fuel cell engineering. , 2004, Chemical reviews.

[12]  Ernest G. Cravalho,et al.  Thermodynamics and kinetics of intracellular ice formation during freezing of biological cells , 1990 .

[13]  Hyunchul Ju,et al.  A single-phase, non-isothermal model for PEM fuel cells , 2005 .

[14]  U. Stimming,et al.  Conductance of Nafion 117 membranes as a function of temperature and water content , 1995 .

[15]  T. Springer,et al.  Polymer Electrolyte Fuel Cell Model , 1991 .

[16]  Chao-Yang Wang,et al.  Effects of operating and design parameters on PEFC cold start , 2007 .

[17]  Tomohiro Ogawa,et al.  The Design and Performance of a PEFC at a Temperature Below Freezing , 2004 .

[18]  J. Acker,et al.  Intercellular ice propagation: experimental evidence for ice growth through membrane pores. , 2001, Biophysical journal.

[19]  Shanhai Ge,et al.  In Situ Imaging of Liquid Water and Ice Formation in an Operating PEFC during Cold Start , 2006 .

[20]  Mario Zedda,et al.  Statistic analysis of operational influences on the cold start behaviour of PEM fuel cells , 2005 .

[21]  Signe Kjelstrup,et al.  Thermal conductivities from temperature profiles in the polymer electrolyte fuel cell , 2004 .

[22]  Chao-Yang Wang,et al.  A Multiphase Model for Cold Start of Polymer Electrolyte Fuel Cells , 2007 .

[23]  R. Mcdonald,et al.  Effects of Deep Temperature Cycling on Nafion® 112 Membranes and Membrane Electrode Assemblies , 2004 .

[24]  Chao-Yang Wang,et al.  Isothermal Cold Start of Polymer Electrolyte Fuel Cells , 2007 .

[25]  In-Hwan Oh,et al.  Effects of Water Removal on the Performance Degradation of PEMFCs Repetitively Brought to < 0 ° C , 2004 .

[26]  Ulrich Stimming,et al.  Proton conduction of Nafion® 117 membrane between 140 K and room temperature , 1994 .

[27]  Kikuko Hayamizu,et al.  Temperature dependence of ion and water transport in perfluorinated ionomer membranes for fuel cells. , 2005, The journal of physical chemistry. B.

[28]  J. Jorné,et al.  Investigation of Low-Temperature Proton Transport in Nafion Using Direct Current Conductivity and Differential Scanning Calorimetry , 2006 .

[29]  W. Kurz,et al.  Fundamentals of Solidification , 1990 .

[30]  In-Hwan Oh,et al.  Characteristics of the PEMFC Repetitively Brought to Temperatures below 0°C , 2003 .