Enhanced tribological properties of MWCNT/Ni bulk composites – Influence of processing on friction and wear behaviour

Abstract The friction and wear behaviour of MWCNT-reinforced Ni matrix bulk composites is investigated and compared to the response of a pure bulk reference sample. Several effects are observed in the composites such as microstructural refinement, leading to improved hardness, coefficient of friction and wear resistance. Said refinement might also be responsible for a non-trivial behaviour of hot-pressed composites under a 300 mN load, due to higher oxidation rates. The worn volume is analysed and discussed from a microstructural and morphological point of view. In this context, a direct correlation is shown between two relevant wear parameters, namely, the wear constant K and the cutting efficiency fAB. In addition, the tribochemistry is investigated by Raman spectroscopy and linked to the friction and wear behaviour. Finally, the wear volume reduction peaked at 94.1% in HUP samples. This clearly indicates the high potential of these composites for tribological applications.

[1]  F. Stott,et al.  The influence of oxides on the friction and wear of alloys , 1978 .

[2]  F. Mücklich,et al.  Thermomechanical Behavior of Bulk Ni/MWNT Composites Produced via Powder Metallurgy , 2012 .

[3]  X. Li,et al.  Tribological behavior of carbon nanotubes—reinforced nickel matrix composite coatings , 2001 .

[4]  Z. Farhat,et al.  Effect of grain size on friction and wear of nanocrystalline aluminum , 1996 .

[5]  F. Stott.  The role of oxidation in the wear of alloys , 1998 .

[6]  D. Lim,et al.  Tribological properties of hot-pressed alumina–CNT composites , 2003 .

[7]  D. Rigney.  Some thoughts on sliding wear , 1992 .

[8]  J. Grabis,et al.  Raman scattering in nanosized nickel oxide NiO , 2007 .

[9]  A. Weibel,et al.  The preparation of double-walled carbon nanotube/Cu composites by spark plasma sintering, and their hardness and friction properties , 2011 .

[10]  R. Colaço,et al.  Laser-assisted combinatorial methods for rapid design of wear resistant iron alloys , 2009 .

[11]  A. Alpas,et al.  Friction and Wear Mechanisms of Nanocrystalline Nickel in Ambient and Inert Atmospheres , 2007 .

[12]  S. Hong,et al.  Hardness and wear resistance of carbon nanotube reinforced Cu matrix nanocomposites , 2007 .

[13]  H. Jang,et al.  Effect of CNT distribution on tribological behavior of alumina–CNT composites , 2005 .

[14]  J. B. Gnanamoorthy,et al.  Influence of grain size on the oxidation resistance of 241Cr-1Mo steel , 1992 .

[15]  Xiaobin Zhang,et al.  An investigation of the sliding wear behavior of Cu-matrix composite reinforced by carbon nanotubes , 2001 .

[16]  Weizhen Chen,et al.  Tribological application of carbon nanotubes in a metal-based composite coating and composites , 2003 .

[17]  R. Banerjee,et al.  Self-lubricating carbon nanotube reinforced nickel matrix composites , 2009 .

[18]  Jing Sun,et al.  Sintering and thermal properties of multiwalled carbon nanotube–BaTiO3 composites , 2005 .

[19]  P. Puech,et al.  The preparation of carbon nanotube (CNT)/copper composites and the effect of the number of CNT walls on their hardness, friction and wear properties , 2013 .

[20]  P. McEuen,et al.  Thermal transport measurements of individual multiwalled nanotubes. , 2001, Physical Review Letters.

[21]  B. Patterson,et al.  Grain growth inhibition by porosity , 1993 .

[22]  Susan B. Sinnott,et al.  Tribological properties of carbon nanotube bundles predicted from atomistic simulations , 2001 .

[23]  A. Kawasaki,et al.  Fabrication and Thermal Properties of Carbon Nanotube/Nickel Composite by Spark Plasma Sintering Method , 2007 .

[24]  P. Liaw,et al.  The mechanical properties of nanostructured materials , 2001 .

[25]  J. Tan,et al.  Microstructure and wear resistance of nickel–carbon nanotube composite coating from brush plating technique , 2006 .