Dendritic counterflow heat exchanger experiments

In this paper we report experimentally the hydraulic and thermal behavior of a balanced counterflow heat exchanger in which each stream flows through a tree-shaped structure covering a circular area. The tree structure is the same on both sides of the heat exchanger: they have three channels reaching/leaving the center, and three branching levels (i.e., 24 channels on the periphery of the circular area). On the hot side, fluid is pumped from the center to the periphery. On the cold side, fluid is pumped from the periphery to the center, and leaves the heat exchanger as a single stream. Two experimental apparatuses were built and tested. In the first design, the body of the heat exchanger was made out of plexiglass and a peripheral plenum was used to collect or distribute the working fluid to the tree structure. The measurements showed that the use of a plenum generates undesirable volumetric flow asymmetries. These lessons led to a second design, which has two major improvements: (i) the heat exchanger core was made out of aluminum and (ii) individual ports (inlets/outlets) were used for each of the peripheral channels. The hydraulic results show a relation between the appearance of volumetric flow rate asymmetries and the bifurcation angles throughout the dendritic structure. The heat transfer results are also discussed.

[1]  J. P. Holman,et al.  Experimental methods for engineers , 1971 .

[2]  Adrian Bejan,et al.  Dendritic constructal heat exchanger with small-scale crossflows and larger-scales counterflows , 2002 .

[3]  A. London,et al.  Compact heat exchangers , 1960 .

[4]  J. Peterson,et al.  Optimization of cost subject to uncertainty constraints in experimental fluid flow and heat transfer , 1991 .

[5]  A. Bontemps,et al.  Liquid flow friction factor and heat transfer coefficient in small channels: an experimental investigation , 2004 .

[6]  Adrian Bejan,et al.  Dendritic fins optimization for a coaxial two-stream heat exchanger , 2004 .

[7]  H. B. Ma and G. P. Peterson.  LAMINAR FRICTION FACTOR IN MICROSCALE DUCTS OF IRREGULAR CROSS SECTION , 1997 .

[8]  David Reay,et al.  Compact Heat Exchangers: Selection, Design and Operation , 2001 .

[9]  S. Garimella,et al.  Investigation of heat transfer in rectangular microchannels , 2005 .

[10]  Adrian Bejan,et al.  Optimal tree-shaped networks for fluid flow in a disc-shaped body , 2002 .

[11]  A. Bejan.  Shape and Structure, from Engineering to Nature , 2000 .

[12]  I. Mudawar,et al.  Experimental and numerical study of pressure drop and heat transfer in a single-phase micro-channel heat sink , 2002 .

[13]  Alexandre K. da Silva,et al.  Constructal multi-scale tree-shaped heat exchangers , 2004 .

[14]  Björn Palm,et al.  Experimental investigation of single-phase convective heat transfer in circular microchannels , 2004 .

[15]  Avram Bar-Cohen,et al.  Design and analysis of heat sinks , 1995 .

[16]  A. Bejan.  Convection Heat Transfer , 1984 .

[17]  G. Peterson,et al.  Convective heat transfer and flow friction for water flow in microchannel structures , 1996 .

[18]  W. Aung,et al.  Cooling Technology for Electronic Equipment , 1988 .

[19]  Gian Piero Celata,et al.  Thermal–hydraulic characteristics of single-phase flow in capillary pipes , 2004 .

[20]  Adrian Bejan,et al.  Dendritic heat convection on a disc , 2003 .

[21]  J. Hansen,et al.  Shape and Structure , 2001 .

[22]  Adrian Bejan,et al.  Entropy generation minimization in parallel‐plates counterflow heat exchangers , 2000 .