Multi-Criteria Decision Making for Optimization of Product Development Under Green Manufacturing Environment

At present, increasing environmental awareness and stringent environmental regulations of the competent authority, the use of green manufacturing (GM) technique is an important topic for the present industries. To overcome the environmental issues, the manufacturing industries use various advanced manufacturing processes for optimal product development. The advance manufacturing process generates large amounts of toxic substances results in various environmental issues during the optimal product manufacturing. Minimization of environmental issues and the amount of waste generated are strongly depends on its process and response parameters. Thus, optimization of process parameters for GM is essential and is a multi-criteria decision making (MCDM) optimization problems. This chapter provides an overview of applications of some MCDM methods for optimization followed by detailed fundamental aspects of optimization issues in green manufacturing. The work proposed an integrated method consisting of AHP coupled with MOORA and validated through an experimental case study.

[1]  Edmundas Kazimieras Zavadskas,et al.  A new additive ratio assessment (ARAS) method in multicriteria decision‐making , 2010 .

[2]  Geoff Pritchard,et al.  Two technologies merge: wood plastic composites , 2004 .

[3]  M. Hashish.  A Modeling Study of Metal Cutting With Abrasive Waterjets , 1984 .

[4]  Jibin Lan,et al.  New parametric prioritization methods for an analytical hierarchy process based on a pairwise comparison matrix , 2011, Math. Comput. Model..

[5]  A. Doniavi,et al.  Empirical Modeling of EDM Parameters Using Grey Relational Analysis , 2008 .

[6]  Edmundas Kazimieras Zavadskas,et al.  The MOORA method and its application to privatization in a transition economy , 2006 .

[7]  Vedansh Chaturvedi,et al.  Multi Response Optimization of Process Parameters of Abrasive Water Jet Machining for Stainless Steel AISI 304 Using VIKOR Approach Coupled with Signal to Noise Ratio Methodology , 2015 .

[8]  Jagadish,et al.  Prediction of surface roughness quality of green abrasive water jet machining: a soft computing approach , 2019, J. Intell. Manuf..

[9]  Vimal Dhokia,et al.  Environmentally conscious machining of difficult-to-machine materials with regard to cutting fluids , 2012 .

[10]  Jagadish,et al.  Prediction and optimization of process parameters of green composites in AWJM process using response surface methodology , 2016, The International Journal of Advanced Manufacturing Technology.

[11]  J. L Lin,et al.  The use of the orthogonal array with grey relational analysis to optimize the electrical discharge machining process with multiple performance characteristics , 2002 .

[12]  Norliana Mohd Abbas,et al.  A review on current research trends in electrical discharge machining (EDM) , 2007 .

[13]  R. Venkata Rao,et al.  Optimization of modern machining processes using advanced optimization techniques: a review , 2014 .

[14]  M. Hashish,et al.  Advances in composite machining with abrasive-waterjets , 1991 .

[15]  Manik Chandra Das,et al.  Decision making under conflicting environment: a new MCDM method , 2012, Int. J. Appl. Decis. Sci..

[16]  L. Tang,et al.  Experimental study on green electrical discharge machining in tap water of Ti–6Al–4V and parameters optimization , 2014 .

[17]  S. Vinodh,et al.  MULTI-OBJECTIVE OPTIMIZATION OF TURNING PARAMETERS USING THE COMBINED MOORA AND ENTROPY METHOD , 2016 .

[18]  S. Hloch,et al.  Turning of wood plastic composites by water jet and abrasive water jet , 2015 .

[19]  Asis Sarkar,et al.  Developing an efficient decision support system for non-traditional machine selection: an application of MOORA and MOOSRA , 2015 .

[20]  S. H. Yeo,et al.  A Method for Green Process Planning in Electric Discharge Machining , 1999 .

[21]  S. H. Yeo,et al.  Assessment of health hazards in production of printed paper packages , 1998 .

[22]  R. K. Springborn.  Non-traditional machining processes , 1967 .

[23]  Jennifer Markarian,et al.  Additive developments aid growth in wood-plastic composites , 2002 .

[24]  P. V. Rao,et al.  Optimisation of process parameters for multi-performance characteristics in EDM of Al2O3 ceramic composite , 2010 .

[26]  Edmundas Kazimieras Zavadskas,et al.  State of art surveys of overviews on MCDM/MADM methods , 2014 .

[27]  Shankar Chakraborty,et al.  Applications of the MOORA method for decision making in manufacturing environment , 2011 .

[28]  Thomas L. Saaty,et al.  DECISION MAKING WITH THE ANALYTIC HIERARCHY PROCESS , 2008 .

[29]  P. Sheng,et al.  Multi-Objective Process Planning in Environmentally Conscious Manufacturing: A Feature-Based Approach , 1995 .

[30]  Chung-Chen Tsao,et al.  Optimization of the EDM parameters on machining Ti–6Al–4V with multiple quality characteristics , 2010 .

[31]  M. Verma,et al.  A Parametric Optimization of Electric Discharge Drill Machine Using Taguchi Approach , 2012 .

[32]  Yan-Cherng Lin,et al.  Optimization of machining parameters using magnetic-force-assisted EDM based on gray relational analysis , 2009 .

[33]  S. Chakraborty,et al.  Application of multi-objective optimization on the basis of ratio analysis (MOORA) method for materials selection , 2012 .

[34]  E. Zavadskas,et al.  Optimization of Weighted Aggregated Sum Product Assessment , 2012 .

[35]  S. P. Sivapirakasam,et al.  Multi-attribute decision making for green electrical discharge machining , 2011, Expert Syst. Appl..