Application of Low-Cost Sensors for Building Monitoring: A Systematic Literature Review

In recent years, many scholars have dedicated their research to the development of low-cost sensors for monitoring of various parameters. Despite their high number of applications, the state of the art related to low-cost sensors in building monitoring has not been addressed. To fill this gap, this article presents a systematic review, following well-established methodology, to analyze the state of the art in two aspects of structural and indoor parameters of buildings, in the SCOPUS database. This analysis allows to illustrate the potential uses of low-cost sensors in the building sector and addresses the scholars the preferred communication protocols and the most common microcontrollers for installation of low-cost monitoring systems. In addition, special attention is paid to describe different areas of the two mentioned fields of building monitoring and the most crucial parameters to be monitored in buildings. Finally, the deficiencies in line with limited number of studies carried out in various fields of building monitoring are overviewed and a series of parameters that ought to be studied in the future are proposed.

[1]  Gerhard P. Hancke,et al.  A Web-Based Office Climate Control System Using Wireless Sensors , 2016, IEEE Sensors Journal.

[2]  Javier Villalba-Diez,et al.  Indoor Air-Quality Data-Monitoring System: Long-Term Monitoring Benefits , 2019, Sensors.

[3]  J. Terés-Zubiaga,et al.  In-use office building energy characterization through basic monitoring and modelling , 2016 .

[4]  Alessandro Sabato,et al.  Feasibility of Frequency-Modulated Wireless Transmission for a Multi-Purpose MEMS-Based Accelerometer , 2014, Sensors.

[5]  G. Fedder,et al.  CMOS-MEMS Capacitive Humidity Sensor , 2009, Journal of Microelectromechanical Systems.

[6]  Les E. Atlas,et al.  Disaggregated water sensing from a single, pressure-based sensor: An extended analysis of HydroSense using staged experiments , 2012, Pervasive Mob. Comput..

[7]  E. Lucchi,et al.  Design and Construction of a New Metering Hot Box for the In Situ Hygrothermal Measurement in Dynamic Conditions of Historic Masonries , 2020, Energies.

[8]  Angelamaria Massimo,et al.  The effect of natural ventilation strategy on indoor air quality in schools. , 2017, The Science of the total environment.

[9]  Lei Zhu,et al.  Design and Application of a Smart Lighting System Based on Distributed Wireless Sensor Networks , 2020 .

[10]  Alessandro Sabato,et al.  A Novel Wireless Accelerometer Board for Measuring Low-Frequency and Low-Amplitude Structural Vibration , 2016, IEEE Sensors Journal.

[11]  Lara del Val,et al.  Design and Validation of a Scalable, Reconfigurable and Low-Cost Structural Health Monitoring System , 2021, Sensors.

[12]  Norberto Fueyo,et al.  Low-cost thermal /spl Sigma/-/spl Delta/ air flow sensor , 2002 .

[13]  Didik R. Santoso,et al.  Wireless sensor module for 3-axis vibration and tilt monitoring on the structural building , 2019 .

[14]  Burcin Becerik-Gerber,et al.  Skin Temperature Extraction Using Facial Landmark Detection and Thermal Imaging for Comfort Assessment , 2019, BuildSys@SenSys.

[15]  Ning Wu,et al.  A Wireless Strain Sensor Network for Structural Health Monitoring , 2015 .

[16]  Felisberto Pereira,et al.  Design of a Cost-Effective Multimodal IoT Edge Device for Building Occupancy Estimation , 2019, 2019 IEEE International Smart Cities Conference (ISC2).

[17]  José Manuel Andújar Márquez,et al.  A New Metre for Cheap, Quick, Reliable and Simple Thermal Transmittance (U-Value) Measurements in Buildings , 2017, Sensors.

[18]  Hyungmin Kim,et al.  An Implantable Wireless Neural Interface System for Simultaneous Recording and Stimulation of Peripheral Nerve with a Single Cuff Electrode , 2017, Sensors.

[19]  Qiangzhou Rong,et al.  Low-frequency fiber Bragg grating accelerometer based on a double-semicircle cantilever , 2014 .

[20]  M. Conti,et al.  IoT Solution based on MQTT Protocol for Real-Time Building Monitoring , 2019, 2019 IEEE 23rd International Symposium on Consumer Technologies (ISCT).

[21]  Matteo Cesana,et al.  Accurate occupancy estimation with WiFi and bluetooth/BLE packet capture , 2019, Comput. Networks.

[22]  Minghong Yang,et al.  A Low Frequency FBG Accelerometer with Symmetrical Bended Spring Plates , 2017, Sensors.

[23]  Jerome P. Lynch,et al.  Wireless feedback structural control with embedded computing , 2006, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[24]  Jerome P. Lynch,et al.  Smart Wireless Sensor Technology for Structural Health Monitoring of Civil Structures , 2009 .

[25]  Kai-Ming Chang,et al.  An automated IoT visualization BIM platform for decision support in facilities management , 2018 .

[26]  Alla Marchenko,et al.  A Systematic Literature Review of Non-Invasive Indoor Thermal Discomfort Detection , 2020, Applied Sciences.

[27]  Yang Zhao,et al.  Virtual occupancy sensors for real-time occupancy information in buildings , 2015 .

[28]  Yang Ting Shen,et al.  Development of Kinetic Facade Units with BIM-Based Active Control System for the Adaptive Building Energy Performance Service , 2016, CAADRIA proceedings.

[29]  J. Braun,et al.  A Chemiresistive CO2 Sensor Based on CNT-Functional Polymer Composite Films , 2020, 2020 IEEE Sensors.

[30]  Orhan Aydin,et al.  An experimental study on the effect of the valve angle of counter-flow Ranque–Hilsch vortex tubes on thermal energy separation , 2010 .

[31]  Venu Gopal Madhav Annamdas Review on Developments in Fiber Optical Sensors and Applications , 2012 .

[33]  Naima Kaabouch,et al.  A Low Cost Through-Wall Radar for Vital Signs Monitoring , 2019, 2019 IEEE International Conference on Electro Information Technology (EIT).

[34]  José Antonio Lozano Galant,et al.  Open source platforms for monitoring thermal parameters of structures , 2021 .

[35]  L. Bragança,et al.  BIM-Based Energy Analysis and Sustainability Assessment—Application to Portuguese Buildings , 2021 .

[36]  Jan Nedoma,et al.  The design of an indirect method for the human presence monitoring in the intelligent building , 2018, Human-centric Computing and Information Sciences.

[37]  Johnny Wong,et al.  Digitisation in facilities management: A literature review and future research directions , 2018, Automation in Construction.

[39]  T. Sharpe,et al.  Field evaluation of a low-cost indoor air quality monitor to quantify exposure to pollutants in residential environments , 2018 .

[40]  Facundo José López,et al.  A Review of Heritage Building Information Modeling (H-BIM) , 2018, Multimodal Technol. Interact..

[41]  Enrique F. Castillo,et al.  Application of Observability Techniques to Structural System Identification , 2013, Comput. Aided Civ. Infrastructure Eng..

[42]  Eric C. Larson,et al.  HydroSense: infrastructure-mediated single-point sensing of whole-home water activity , 2009, UbiComp.

[43]  Ming-Ta Yang,et al.  Design and Implementation of an Intelligent Windowsill System Using Smart Handheld Device and Fuzzy Microcontroller , 2017, Sensors.

[44]  Yang Yang,et al.  Flextensional fiber Bragg grating-based accelerometer for low frequency vibration measurement , 2011 .

[45]  Subhas Chandra Mukhopadhyay,et al.  Ventilation Monitoring and Control System for High Rise Historical Buildings , 2017, IEEE Sensors Journal.

[46]  Laurent Spinelle,et al.  Review of Portable and Low-Cost Sensors for the Ambient Air Monitoring of Benzene and Other Volatile Organic Compounds , 2017, Sensors.

[47]  Hsm Helianthe Kort,et al.  Occupancy-based lighting control in open-plan office spaces: A state-of-the-art review , 2017 .

[48]  Huan Wang,et al.  Non-invasive (non-contact) measurements of human thermal physiology signals and thermal comfort/discomfort poses -A review , 2020, Energy and Buildings.

[49]  Ahmed H. Osman,et al.  Vibration Signature of Normal and Notched Tooth Gear Pump , 2019 .

[50]  M. I. Seht,et al.  Microtremor measurements used to map thickness of soft sediments , 1999 .

[51]  Thomas H. Heaton,et al.  Structural health monitoring through dense instrumentation by community participants: the Community Seismic Network and Quake-Catcher Network , 2014 .

[52]  Michele Penza,et al.  Urban Air Quality Monitoring with Networked Low-Cost Sensor-Systems , 2017 .

[53]  Michel Gerboles,et al.  Review of the Performance of Low-Cost Sensors for Air Quality Monitoring , 2019, Atmosphere.

[54]  A. Rosenfeld,et al.  Estimates of Improved Productivity and Health from Better Indoor Environments , 1997 .

[55]  Guido Perrone,et al.  Plastic Optical Fiber Displacement Sensor for Cracks Monitoring , 2007 .

[56]  M. Davies,et al.  A `pad' sensor for measuring the moisture content of building materials , 2009 .

[57]  José Manuel Andújar Márquez,et al.  A new and inexpensive temperature-measuring system: Application to photovoltaic solar facilities , 2009 .

[58]  Gerhard P. Hancke,et al.  An Energy-Efficient Smart Comfort Sensing System Based on the IEEE 1451 Standard for Green Buildings , 2014, IEEE Sensors Journal.

[59]  Behnam Mobaraki,et al.  New Image Recognition Technique for Intuitive Understanding in Class of the Dynamic Response of High-Rise Buildings , 2021, Sustainability.

[60]  Suryaa Pranav Meduri,et al.  A Sophisticated Irrigation System with Passive and Analogue Sensors over Web Using Orange Pi , 2020, 2020 Third International Conference on Smart Systems and Inventive Technology (ICSSIT).

[61]  Anuj Kumar,et al.  An Approach Towards Development Of Pmv Based Thermal Comfort Smart Sensor , 2010 .

[62]  S. Nutt,et al.  All-printed strain sensors: Building blocks of the aircraft structural health monitoring system , 2017 .

[63]  Theanh Nguyen,et al.  Very sensitive fiber Bragg grating accelerometer using transverse forces with an easy over-range protection and low cross axial sensitivity. , 2013, Applied optics.

[64]  Nélia Alberto,et al.  Optical Sensors Based on Plastic Fibers , 2012, Sensors.

[65]  Ali Motamedi,et al.  BIM- and IoT-based virtual reality tool for real-time thermal comfort assessment in building enclosures , 2021, Building and Environment.

[66]  Claudia Guattari,et al.  Influence of heating systems on thermal transmittance evaluations: Simulations, experimental measurements and data post-processing , 2018, Energy and Buildings.

[67]  K. Tutuncu,et al.  Embedded Fuzzy Logic Control System for Refrigerated Display Cabinets , 2019, Arabian Journal for Science and Engineering.

[68]  A. Rudke,et al.  Biodegradable CA/CPB electrospun nanofibers for efficient retention of airborne nanoparticles , 2020, Process Safety and Environmental Protection.

[69]  M. Vaghefi,et al.  Effect of the soil type on the dynamic response of a tunnel under surface detonation , 2016 .

[70]  J. Lozano-Galant,et al.  Environmental Monitoring System Based on Low-Cost Sensors , 2020 .

[71]  Jovan S. Bajić,et al.  Application of fiber-optic curvature sensor in deformation measurement process , 2016 .

[72]  Wilson Negrão Macêdo,et al.  A Low-Cost, Stand-Alone Sensory Platform for Monitoring Extreme Solar Overirradiance Events , 2018, Sensors.

[73]  Y. Wang,et al.  Implementation of a closed‐loop structural control system using wireless sensor networks , 2008 .

[74]  David Bienvenido-Huertas,et al.  Determining the U-Value of Façades Using the Thermometric Method: potentials and limitations , 2018 .

[75]  Gerhard P. Hancke,et al.  A wireless system for indoor air quality monitoring , 2016, IECON 2016 - 42nd Annual Conference of the IEEE Industrial Electronics Society.

[76]  Eduard Clotet,et al.  A proposal of low-cost and low-power embedded wireless image sensor node for IoT applications , 2018, FNC/MobiSPC.

[77]  Liping Wang,et al.  Continuous monitoring of indoor environmental quality using an Arduino-based data acquisition system , 2018, Journal of Building Engineering.

[78]  Weiming Shen,et al.  Implicit occupancy detection for energy conservation in commercial buildings: A review , 2016, 2016 IEEE 20th International Conference on Computer Supported Cooperative Work in Design (CSCWD).

[79]  A. Campagna,et al.  Indoor Air Quality , 2017, American journal of lifestyle medicine.

[80]  V. M. Sineglazov,et al.  ENVIRONMENTAL CHAMBER FOR NAVIGATION EQUIPMENT TEST TABLE , 2017 .

[81]  Laddu Bhagya Jayasinghe,et al.  BIM-Based End-of-Lifecycle Decision Making and Digital Deconstruction: Literature Review , 2020 .

[82]  Maitreyee Dutta,et al.  Indoor Air Quality Monitoring Systems Based on Internet of Things: A Systematic Review , 2020, International journal of environmental research and public health.

[83]  Mohataz Hossain,et al.  Application of IoT and BEMS to Visualise the Environmental Performance of an Educational Building , 2020, Energies.

[84]  Xiaoyi Mu,et al.  Low Power Multimode Electrochemical Gas Sensor Array System for Wearable Health and Safety Monitoring , 2014, IEEE Sensors Journal.

[86]  P. S. Harvey,et al.  Pixel-based operating modes from surveillance videos for structural vibration monitoring: A preliminary experimental study , 2019 .

[87]  P. Giungato,et al.  Indoor air quality in schools , 2014, Environmental Chemistry Letters.

[88]  Marco Di Felice,et al.  Structural Health Monitoring and Prognostic of Industrial Plants and Civil Structures: A Sensor to Cloud Architecture , 2020, IEEE Instrumentation & Measurement Magazine.

[89]  Y. Chan,et al.  Developing the methodology to investigate the thermal comfort of hot-humid climate under different ventilation modes , 2019, Journal of Physics: Conference Series.

[90]  Gian Marco Revel,et al.  Cost-effective technologies to control indoor air quality and comfort in energy efficient building retrofitting , 2015 .

[91]  Yajun Jiang,et al.  Strain-insensitive twist and temperature sensor based on seven-core fiber , 2019, Sensors and Actuators A: Physical.

[92]  Luis Eduardo Mujica Delgado,et al.  Embedded piezodiagnostics for online structural damage detection based on PCA algorithm , 2016 .

[93]  Wenbin Li,et al.  Automatic Indoor as-Built Building Information Models Generation by Using Low-Cost RGB-D Sensors , 2020, Sensors.

[94]  Salvatore Baglio,et al.  A low cost multi-sensor approach for early warning in structural monitoring of buildings and structures , 2014, 2014 IEEE International Instrumentation and Measurement Technology Conference (I2MTC) Proceedings.

[95]  Ravi Kishore Kodali,et al.  Low cost ambient monitoring using ESP8266 , 2016, 2016 2nd International Conference on Contemporary Computing and Informatics (IC3I).

[96]  W Wim Zeiler,et al.  The user as sensor to reach for optimal individual comfort and reduced energy consumption , 2012 .

[97]  Kofi A. A. Makinwa,et al.  A Phase-Domain Readout Circuit for a CMOS-Compatible Hot-Wire CO2 Sensor , 2018, IEEE Journal of Solid-State Circuits.

[98]  Byeol Kim,et al.  Advanced Wireless Sensor Networks for Sustainable Buildings Using Building Ducts , 2018, Sustainability.

[99]  Ting-Yu Hsu,et al.  Application of the low-cost MEMS-type seismometer for structural health monitoring: A pre-study , 2016, 2016 IEEE International Instrumentation and Measurement Technology Conference Proceedings.

[100]  B. F. Spencer,et al.  Development of a High-Sensitivity Wireless Accelerometer for Structural Health Monitoring , 2018, Sensors.

[101]  Anand Nayyar,et al.  A Comprehensive Review of BeagleBone Technology: Smart Board Powered by ARM , 2016 .

[102]  David K. Y. Yau,et al.  An Experimental Low-Cost, Low-Data-Rate Rapid Structural Assessment Network , 2009, IEEE Sensors Journal.

[103]  S. Costea,et al.  Structural health monitoring using an array of spatially distributed sensors , 2009, 2009 International Semiconductor Conference.

[104]  Hasan Hayat,et al.  The State-of-the-Art of Sensors and Environmental Monitoring Technologies in Buildings , 2019, Sensors.

[105]  Umit Isikdag,et al.  INTEGRATION OF BIM, WEB MAPS AND IOT FOR SUPPORTING COMFORT ANALYSIS , 2017 .

[106]  Michael L. Kuntzman,et al.  Micromachined Piezoelectric Accelerometers via Epitaxial Silicon Cantilevers and Bulk Silicon Proof Masses , 2013, Journal of Microelectromechanical Systems.

[107]  Konstantinos Oikonomou,et al.  Structural Health Monitoring in Historical Buildings: A Network Approach , 2020, Heritage.

[108]  Reda Yaagoubi,et al.  Dynamic Predicted Mean Vote: An IoT-BIM integrated approach for indoor thermal comfort optimization , 2021 .

[109]  Mohammad Vaghefi,et al.  Numerical study of the depth and cross-sectional shape of tunnel under surface explosion , 2015 .

[110]  Yang Wang,et al.  Laboratory Evaluation and Calibration of Three Low-Cost Particle Sensors for Particulate Matter Measurement , 2015 .

[111]  Yuebin Yu,et al.  Virtual calibration of a supply air temperature sensor in rooftop air conditioning units , 2011 .

[112]  Stefano Lenci,et al.  A Genetic Algorithm Procedure for the Automatic Updating of FEM Based on Ambient Vibration Tests , 2020, Sensors.

[113]  K. Katsaros,et al.  The K-Gill: A Twin Propeller-Vane Anemometer for Measurements of Atmospheric Turbulence , 1989 .

[114]  Anuj Kumar,et al.  Sensing, Controlling, and IoT Infrastructure in Smart Building: A Review , 2019, IEEE Sensors Journal.

[115]  V. Denoël,et al.  Vortex induced vibrations of rectangular cylinders arranged on a grid , 2018, Journal of Wind Engineering and Industrial Aerodynamics.

[116]  Irshad Khan,et al.  A Smart IoT Device for Detecting and Responding to Earthquakes , 2019, Electronics.

[117]  Jose Antonio Lozano-Galant,et al.  Structural system identification of thin web bridges by observability techniques considering shear deformation , 2018 .

[118]  Lukasz Niestoruk,et al.  Real-time environmental emission monitoring on construction sites , 2014, 2014 6th European Embedded Design in Education and Research Conference (EDERC).

[119]  Jerome Peter Lynch,et al.  An overview of wireless structural health monitoring for civil structures , 2007, Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences.

[120]  Gian Marco Revel,et al.  Experimental testing of a system for the energy-efficient sub-zonal heating management in indoor environments based on PMV , 2018 .

[121]  P. Orlano GEOMATIC TECHNIQUES FOR THE COLONNADE STRUCTURAL ANALYSIS OF THE HISTORICAL “CHIARAMONTE STERI” BUILDING , 2019, The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences.

[122]  Willemien Anaf,et al.  Real-Time Wood Behaviour: The Use of Strain Gauges for Preventive Conservation Applications , 2020, Sensors.

[123]  Guido Perrone,et al.  Broadband Source-Based Interrogation Scheme of Fiber Bragg Grating Sensors for Structural Health Monitoring , 2007 .

[124]  Hui Li,et al.  Modeling Wireless Signal Transmission Performance Path Loss for ZigBee Communication Protocol in Residential Houses , 2009 .

[125]  Marco Aiello,et al.  Beyond Indoor Presence Monitoring with Simple Sensors , 2012, PECCS.

[126]  Baizhan Li,et al.  Prediction of thermal sensation using low-cost infrared array sensors monitoring system , 2019, IOP Conference Series: Materials Science and Engineering.

[128]  Federico Viani,et al.  A forecasting strategy based on wireless sensing for thermal comfort optimization in smart buildings , 2017 .

[129]  Ning Yang,et al.  Design of a Piezoelectric Accelerometer with High Sensitivity and Low Transverse Effect , 2016, Sensors.

[130]  Alexis K.H. Lau,et al.  Energy consumption, indoor thermal comfort and air quality in a commercial office with retrofitted heat, ventilation and air conditioning (HVAC) system , 2019, Energy and Buildings.

[131]  António Barrias,et al.  A Review of Distributed Optical Fiber Sensors for Civil Engineering Applications , 2016, Sensors.

[132]  Michele Arturo Caponero,et al.  Use of fibre optic sensors for structural monitoring of temporary emergency reinforcements of the church S. Maria delle Grazie in Accumoli , 2019 .

[133]  Eunshin Byon,et al.  HEAT - Human Embodied Autonomous Thermostat , 2020 .

[134]  Changbum R. Ahn,et al.  Assessing occupants’ energy load variation through existing wireless network infrastructure in commercial and educational buildings , 2014 .

[135]  Wilhelm Kleiminger,et al.  The Comfstat - automatically sensing thermal comfort for smart thermostats , 2017, 2017 IEEE International Conference on Pervasive Computing and Communications (PerCom).

[136]  G. Stamatescu,et al.  Evaluation of wireless sensor network monitoring for indoor spaces , 2012, 2012 International Symposium on Instrumentation & Measurement, Sensor Network and Automation (IMSNA).

[137]  Silvia Lamonaca,et al.  Control of framed structures using intelligent monitoring networks , 2017 .

[138]  Miguel Morales,et al.  Energy Diagnosis of University Buildings: Renewable Energy Institute from UNAM , 2018, Buildings.

[139]  D. Rubenstein,et al.  An Intelligent Wireless Structural Health Monitoring Solution , 2011 .

[140]  Elena Lucchi,et al.  Development of a Compatible, Low Cost and High Accurate Conservation Remote Sensing Technology for the Hygrothermal Assessment of Historic Walls , 2019, Electronics.

[141]  Massimiliano Scarpa,et al.  Development and testing of a platform aimed at pervasive monitoring of indoor environment and building energy , 2017 .

[142]  Yu-Cheng Lin,et al.  A Real-Time Construction Safety Monitoring System for Hazardous Gas Integrating Wireless Sensor Network and Building Information Modeling Technologies , 2018, Sensors.

[143]  Jerome P. Lynch,et al.  A summary review of wireless sensors and sensor networks for structural health monitoring , 2006 .

[144]  Yen Kheng Tan,et al.  Advanced building energy monitoring using wireless sensor integrated EnergyPlus platform for personal climate control , 2015, 2015 IEEE 11th International Conference on Power Electronics and Drive Systems.

[145]  Jakub Markiewicz,et al.  The Quality Assessment of Different Geolocalisation Methods for a Sensor System to Monitor Structural Health of Monumental Objects , 2020, Sensors.

[146]  Haiying Ma,et al.  Structural Health Monitoring of 2D Plane Structures , 2021 .

[147]  Cristian Perra,et al.  BIM and IoT Sensors Integration: A Framework for Consumption and Indoor Conditions Data Monitoring of Existing Buildings , 2021, Sustainability.

[148]  Hojjat Adeli,et al.  System identification in structural engineering , 2012 .

[149]  Talal Rahwan,et al.  Automatic HVAC Control with Real-time Occupancy Recognition and Simulation-guided Model Predictive Control in Low-cost Embedded System , 2017, ArXiv.

[150]  J. Ingham,et al.  Measured response of instrumented buildings during the July 2013 Cook Strait earthquake sequence , 2015 .

[151]  Michele De Carli,et al.  Measured and perceived indoor environmental quality: Padua Hospital case study , 2013 .

[152]  Pawel Wargocki,et al.  Ten questions concerning thermal and indoor air quality effects on the performance of office work and schoolwork , 2017 .

[153]  Marco Pieralisi,et al.  Design of a low cost and high performance wireless sensor network for structural health monitoring , 2016 .

[154]  Markku Mattila,et al.  Effective supervisory behaviour and safety at the building site , 1994 .

[155]  W Wim Zeiler,et al.  On the application of wireless sensors and actuators network in existing buildings for occupancy detection and occupancy-driven lighting control , 2016 .

[156]  Yuichiro Yamabe,et al.  Fundamental Tests on a Structural Health Monitoring System for Building Structures Using a Single-board Microcontroller , 2015 .

[157]  Stephen Selkowitz,et al.  Development and assessment of a low cost sensor for solar heat flux measurements in buildings , 2015 .

[158]  Haorong Li,et al.  An improved virtual calibration of a supply air temperature sensor in rooftop air conditioning units , 2011 .

[159]  Wei Wang,et al.  Modeling occupancy distribution in large spaces with multi-feature classification algorithm , 2018 .

[160]  Jürgen Wöllenstein,et al.  A Wireless Gas Sensor Network to Monitor Indoor Environmental Quality in Schools , 2018, Sensors.

[161]  D. Briand,et al.  A low-power micromachined MOSFET gas sensor , 2000, Journal of Microelectromechanical Systems.

[162]  Jose Antonio Lozano-Galant,et al.  Constrained observability method in static structural system identification , 2018 .

[163]  Carmine Landi,et al.  Implementation of a distributed Stand Alone Merging Unit , 2018, Journal of Physics: Conference Series.

[164]  Ki-Hyun Kim,et al.  The Relative Performance of NDIR-based Sensors in the Near Real-time Analysis of CO2 in Air , 2007, Sensors.

[165]  Travis Walter,et al.  Assessing the Energy Resilience of Office Buildings: Development and Testing of a Simplified Metric for Real Estate Stakeholders , 2021, Buildings.

[166]  Chiara Bedon,et al.  Dynamic Characterisation and Finite Element Updating of a RC Stadium Grandstand , 2018, Buildings.

[167]  Krishnan Balasubramaniam,et al.  DEVELOPMENT OF A STAMP SIZE PULSER‐RECEIVER FOR STRUCTURAL HEALTH MONITORING APPLICATIONS , 2011 .

[168]  K. Ćmielewski,et al.  Accuracy and functional assessment of an original low-cost fibre-based inclinometer designed for structural monitoring , 2020 .

[169]  Karen Kensek Integration of Environmental Sensors with BIM: Case studies using Arduino, Dynamo, and the Revit API , 2014 .

[170]  Zoltán Nagy,et al.  Wireless sensor network for estimating building performance , 2020 .

[171]  Peyman Servati,et al.  Room temperature ultra-sensitive resistive humidity sensor based on single zinc oxide nanowire , 2012 .

[172]  Ali Motamedi,et al.  Live Data Visualization of IoT Sensors Using Augmented Reality (AR) and BIM , 2019, Proceedings of the 36th International Symposium on Automation and Robotics in Construction (ISARC).

[173]  Thomas R. Allen,et al.  Structural responses of high performance sailing yachts to slamming loads , 2011 .

[174]  Jose Turmo,et al.  Practical Application of Low-Cost Sensors for Static Tests , 2020 .

[175]  Jochen Teizer,et al.  Internet of Things (IoT) for Integrating Environmental and Localization Data in Building Information Modeling (BIM) , 2017 .

[176]  Zoltán Nagy,et al.  An easily-deployable wireless sensor network for building energy performance assessment , 2017 .

[177]  Qiang Zou,et al.  Highly symmetric tri-axis piezoelectric bimorph accelerometer , 2004, 17th IEEE International Conference on Micro Electro Mechanical Systems. Maastricht MEMS 2004 Technical Digest.

[178]  Billie F. Spencer,et al.  Smart sensing technology: opportunities and challenges , 2004 .

[179]  Jie Hao,et al.  Light Sensor Based Occupancy Estimation via Bayes Filter With Neural Networks , 2020, IEEE Transactions on Industrial Electronics.

[180]  Antonino D'Alessandro,et al.  MEMS-Based System for Structural Health Monitoring and Earthquake Observation in Sicily , 2021, Lecture Notes in Civil Engineering.

[181]  Abderrahmane Baïri,et al.  Environmental monitoring system based on an Open Source Platform and the Internet of Things for a building energy retrofit , 2018 .

[182]  Mauno Rönkkö,et al.  Designing Resilience Mediators for Control Systems , 2014 .

[183]  Mikkel Baun Kjærgaard,et al.  Modelling urban-scale occupant behaviour, mobility, and energy in buildings: A survey , 2020, Building and Environment.

[184]  Besarion Meskhi,et al.  Structural Monitoring of Underground Structures in Multi-Layer Media by Dynamic Methods , 2020, Sensors.

[185]  Jiayu Li,et al.  Optical characterization studies of a low-cost particle sensor , 2017 .

[186]  Mahmood Yaghoubi,et al.  Experimental study of frost formation on a fin-and-tube heat exchanger by natural convection , 2014 .

[187]  Mihaela Teni,et al.  Review and comparison of current experimental approaches for in-situ measurements of building walls thermal transmittance , 2019, Energy and Buildings.

[188]  Andrew Peacock,et al.  An evidence based approach to determining residential occupancy and its role in demand response management , 2016 .

[189]  Jose Turmo,et al.  A Comprehensive Description of a Low-Cost Wireless Dynamic Real-Time Data Acquisition and Monitoring System , 2020 .

[190]  Brent Stephens,et al.  Methods to assess human occupancy and occupant activity in hospital patient rooms , 2015 .

[191]  Raymond M. Measures,et al.  Fiber optic sensing for composite smart structures , 1993 .

[192]  M. Sun,et al.  Smart Sensing Technologies for Structural Health Monitoring of Civil Engineering Structures , 2010 .

[193]  Wei Yan,et al.  BPOpt: A framework for BIM-based performance optimization , 2015 .