Aerial tool operation system using quadrotors as Rotating Thrust Generators

We propose a new aerial tool operation system consisting of multiple quadrotors connected to a tool by spherical joints to perform tool operation tasks. We model the system and show that the attitude dynamics of each quadrotor is decoupled from the tool dynamics, so that we can consider the quadrotors as thrusters and control the tool by adjusting the orientation and magnitude of these thrusters. We also show that the 6-DOF tool dynamics could be under-actuated or fully-actuated, depending on the number of quadrotors attached to the tool and the geometric configuration of their attachments. We then design control laws for the tool-tip position/orientation tracking of the (under-actuated) tool system with two quadrotors and the (fully-actuated) tool system with three quadrotors. We use Lyapunov approach to find the desired thrust command for each quadrotor while also taking into account the spherical joint limits in a form of constrained optimization. Simulation and implementation results are performed to support the theory.

[1]  Lorenzo Marconi,et al.  Modeling and Control of a Class of Modular Aerial Robots Combining Under Actuated and Fully Actuated Behavior , 2015, IEEE Transactions on Control Systems Technology.

[2]  ChangSu Ha,et al.  Mechanics, control and internal dynamics of quadrotor tool operation , 2015, Autom..

[3]  Dongjun Lee,et al.  Dynamics and control of quadrotor with robotic manipulator , 2014, 2014 IEEE International Conference on Robotics and Automation (ICRA).

[4]  Heinrich H. Bülthoff,et al.  On-board velocity estimation and closed-loop control of a quadrotor UAV based on optical flow , 2012, 2012 IEEE International Conference on Robotics and Automation.

[5]  ChangSu Ha,et al.  Passivity-based adaptive backstepping control of quadrotor-type UAVs , 2014, Robotics Auton. Syst..

[6]  Jiawei Li,et al.  On Computing Three-Finger Force-Closure Grasps , 2003 .

[7]  Dongjun Lee,et al.  MECHANICS AND CONTROL OF QUADROTORS FOR TOOL OPERATION , 2012 .

[8]  Vijay Kumar,et al.  Cooperative Grasping and Transport Using Multiple Quadrotors , 2010, DARS.

[9]  N.H. McClamroch,et al.  Stabilization of Underactuated 3D Pendulum Using Partial Angular Velocity Feedback , 2005, Proceedings of the 44th IEEE Conference on Decision and Control.

[10]  Naomi Ehrich Leonard,et al.  Autonomous rigid body attitude synchronization , 2007, 2007 46th IEEE Conference on Decision and Control.

[11]  Vijay Kumar,et al.  Planning and control for cooperative manipulation and transportation with aerial robots , 2011, Int. J. Robotics Res..

[12]  Dongjun Lee,et al.  Hybrid force/motion control and internal dynamics of quadrotors for tool operation , 2013, 2013 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[13]  Vijay Kumar,et al.  Cooperative manipulation and transportation with aerial robots , 2009, Auton. Robots.

[14]  Joris De Schutter,et al.  A hybrid pose / wrench control framework for quadrotor helicopters , 2012, 2012 IEEE International Conference on Robotics and Automation.

[15]  Peter I. Corke,et al.  Multirotor Aerial Vehicles: Modeling, Estimation, and Control of Quadrotor , 2012, IEEE Robotics & Automation Magazine.

[16]  Lorenzo Marconi,et al.  A modular aerial vehicle with redundant actuation , 2013, 2013 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[17]  Stephen P. Boyd,et al.  Fast Computation of Optimal Contact Forces , 2007, IEEE Transactions on Robotics.