Hybrid approach combining multiple characterization techniques and simulations for microstructural analysis of proton exchange membrane fuel cell electrodes

Abstract The cost and performance of proton exchange membrane fuel cells strongly depend on the cathode electrode due to usage of expensive platinum (Pt) group metal catalyst and sluggish reaction kinetics. Development of low Pt content high performance cathodes requires comprehensive understanding of the electrode microstructure. In this study, a new approach is presented to characterize the detailed cathode electrode microstructure from nm to μm length scales by combining information from different experimental techniques. In this context, nano-scale X-ray computed tomography (nano-CT) is performed to extract the secondary pore space of the electrode. Transmission electron microscopy (TEM) is employed to determine primary C particle and Pt particle size distributions. X-ray scattering, with its ability to provide size distributions of orders of magnitude more particles than TEM, is used to confirm the TEM-determined size distributions. The number of primary pores that cannot be resolved by nano-CT is approximated using mercury intrusion porosimetry. An algorithm is developed to incorporate all these experimental data in one geometric representation. Upon validation of pore size distribution against gas adsorption and mercury intrusion porosimetry data, reconstructed ionomer size distribution is reported. In addition, transport related characteristics and effective properties are computed by performing simulations on the hybrid microstructure.

[1]  G Sasikumar,et al.  Dependence of optimum Nafion content in catalyst layer on platinum loading , 2004 .

[2]  Partha P. Mukherjee,et al.  Stochastic Microstructure Reconstruction and Direct Numerical Simulation of the PEFC Catalyst Layer , 2006 .

[3]  E. Passalacqua,et al.  Influence of Nafion loading in the catalyst layer of gas-diffusion electrodes for PEFC , 1999 .

[4]  S. Minko,et al.  Imaging and Microanalysis of Thin Ionomer Layers by Scanning Transmission Electron Microscopy , 2014 .

[5]  S. H. Kim,et al.  Reconstruction and Effective Transport Properties of the Catalyst Layer in PEM Fuel Cells , 2009 .

[6]  K. Karan,et al.  An improved two-dimensional agglomerate cathode model to study the influence of catalyst layer structural parameters , 2005 .

[7]  A. Morin,et al.  Three-dimensional analysis of Nafion layers in fuel cell electrodes , 2014, Nature Communications.

[8]  Partha P. Mukherjee,et al.  Optimization of polymer electrolyte fuel cell cathode catalyst layers via direct numerical simulation modeling , 2007 .

[9]  F. Maillard,et al.  Detection of Pt z + Ions and Pt Nanoparticles Inside the Membrane of a Used PEMFC , 2007 .

[10]  Fuqiang Liu,et al.  Process based reconstruction and simulation of a three-dimensional fuel cell catalyst layer , 2010 .

[11]  S. Litster,et al.  Effects of an agglomerate size distribution on the PEFC agglomerate model , 2012 .

[12]  A. Menzel,et al.  Enhancing the quality of the tomography of nanoporous materials for better understanding of polymer electrolyte fuel cell materials , 2015 .

[13]  Ned Djilali,et al.  Pore Scale Simulation of Transport and Electrochemical Reactions in Reconstructed PEMFC Catalyst Layers , 2010 .

[14]  Yang Shao-Horn,et al.  Formation Mechanism of Pt Single-Crystal Nanoparticles in Proton Exchange Membrane Fuel Cells , 2007 .

[15]  S. Litster,et al.  Resolving the Three‐Dimensional Microstructure of Polymer Electrolyte Fuel Cell Electrodes using Nanometer‐Scale X‐ray Computed Tomography , 2012 .

[16]  Nigel P. Brandon,et al.  Using Synchrotron X-Ray Nano-CT to Characterize SOFC Electrode Microstructures in Three-Dimensions at Operating Temperature , 2011 .

[17]  Karren L. More,et al.  Porosimetry of MEAs Made by “Thin Film Decal” Method and Its Effect on Performance of PEFCs , 2004 .

[18]  Edson A. Ticianelli,et al.  Development and electrochemical studies of gas diffusion electrodes for polymer electrolyte fuel cells , 1996 .

[19]  Yuko Aoyama,et al.  Investigation of the Microstructure in the Catalyst Layer and Effects of Both Perfluorosulfonate Ionomer and PTFE‐Loaded Carbon on the Catalyst Layer of Polymer Electrolyte Fuel Cells , 1995 .

[20]  Z. Qi,et al.  Low Pt loading high performance cathodes for PEM fuel cells , 2003 .

[21]  Pete R. Jemian,et al.  Irena: tool suite for modeling and analysis of small‐angle scattering , 2009 .

[22]  A. Ohma,et al.  Analysis of the Microstructure Formation Process and Its Influence on the Performance of Polymer Electrolyte Fuel‐Cell Catalyst Layers , 2015 .

[23]  Li Xu,et al.  Simulation of the catalyst layer in PEMFC based on a novel two-phase lattice model , 2011 .

[24]  Sandip Mazumder,et al.  Generalized flooded agglomerate model for the cathode catalyst layer of a polymer electrolyte membrane fuel cell , 2012 .

[25]  Kyle J. Lange,et al.  Determination of effective transport properties in a PEMFC catalyst layer using different reconstruction algorithms , 2012 .

[26]  R. Zengerle,et al.  Direct three-dimensional reconstruction of a nanoporous catalyst layer for a polymer electrolyte fuel cell , 2011 .

[27]  Karren L. More,et al.  Influence of ionomer content on the structure and performance of PEFC membrane electrode assemblies , 2010 .

[28]  A. Prasad,et al.  Three dimensional proton exchange membrane fuel cell cathode model using a modified agglomerate approach based on discrete catalyst particles , 2014 .

[29]  Suresh G. Advani,et al.  An Improved Agglomerate Model for the PEM Catalyst Layer with Accurate Effective Surface Area Calculation Based on the Sphere-Packing Approach , 2014 .

[30]  Afzal Suleman,et al.  Multi-variable optimization of PEMFC cathodes using an agglomerate model , 2007 .

[31]  Roland Zengerle,et al.  Nano-morphology of a polymer electrolyte fuel cell catalyst layer—imaging, reconstruction and analysis , 2011 .

[32]  Karren L. More,et al.  Microstructural Changes of Membrane Electrode Assemblies during PEFC Durability Testing at High Humidity Conditions , 2005 .

[33]  Kourosh Malek,et al.  On the micro-, meso-, and macroporous structures of polymer electrolyte membrane fuel cell catalyst layers. , 2010, ACS applied materials & interfaces.

[34]  G. Squadrito,et al.  Nafion content in the catalyst layer of polymer electrolyte fuel cells: effects on structure and performance , 2001 .

[35]  Fan Zhang,et al.  Ultra‐small‐angle X‐ray scattering at the Advanced Photon Source , 2009 .

[36]  Shawn Litster,et al.  Resolving Electrode Morphology's Impact on Platinum Group Metal-Free Cathode Performance Using Nano-CT of 3D Hierarchical Pore and Ionomer Distribution. , 2016, ACS applied materials & interfaces.

[37]  Hubert A. Gasteiger,et al.  Instability of Pt ∕ C Electrocatalysts in Proton Exchange Membrane Fuel Cells A Mechanistic Investigation , 2005 .

[38]  Surya R. Kalidindi,et al.  Morphological Analyses of Polymer Electrolyte Fuel Cell Electrodes with Nano‐Scale Computed Tomography Imaging , 2013 .