Microstructure and Mechanical Properties of Silicon Nitride Ceramics with Controlled Porosity

Porous silicon nitride ceramic with a porosity from 0-0.3 was fabricated by partial hot-pressing of a powder mixture of α-Si 3 N 4 and 5 wt% Yb 2 O 3 as sintering additive. Irrespective of the porosity, the samples exhibited almost the same microstructural features including grain size, grain aspect ratio, and pore size. Porosity dependences of Young's modulus, flexural strength, and fracture toughness (K 1c ) were investigated. All these properties decreased with increasing porosity. However, because of the fibrous microstructure, the decreases of flexural strength and fracture toughness were moderate compared with the much greater decrease of Young's modulus. Thus, the strain tolerance (fracture strength/Young's modulus) increased with increasing porosity. The critical energy release rate also increased slightly with an increasing volume fraction of porosity to 0.166 and remained at the same level with that of the dense sample when the porosity was 0.233. They decreased as porosity increased further.

[1]  K. Niihara,et al.  Influence of Yttria–Alumina Content on Sintering Behavior and Microstructure of Silicon Nitride Ceramics , 2004 .

[2]  Janet B. Davis,et al.  Fabrication and Crack Deflection in Ceramic Laminates with Porous Interlayers , 2004 .

[3]  Guo‐Jun Zhang,et al.  In-Situ Reaction Synthesis of Non-Oxide Boron Nitride Composites , 2002 .

[4]  Guo‐Jun Zhang,et al.  Porosity and microstructure control of porous ceramics by partial hot pressing , 2001 .

[5]  Guo‐Jun Zhang,et al.  High‐Surface‐Area Alumina Ceramics Fabricated by the Decomposition of Al(OH)3 , 2001 .

[6]  F. Lange,et al.  Processing and properties of an all-oxide composite with a porous matrix , 2000 .

[7]  Guo‐Jun Zhang,et al.  Effect of BN content on elastic modulus and bending strength of SiC-BN in situ composites , 1999 .

[8]  Y. Choa,et al.  Mechanical Properties of Si3N4/BN Composites by Chemical Processing , 1998 .

[9]  C. A. Andersson.  Derivation of the Exponential Relation for the Effect of Ellipsoidal Porosity on Elastic Modulus , 1996 .

[10]  R. Rice.  Comparison of physical property-porosity behaviour with minimum solid area models , 1996, Journal of Materials Science.

[11]  A. Evans,et al.  Mechanical Properties of Partially Dense Alumina Produced from Powder Compacts , 1994 .

[12]  Tsutomu T. Mori,et al.  Analysis of Dependence of Volume Fraction and Micropore Shape on Fracture Toughness by the Equivalent Inclusion Method , 1991 .

[13]  Tohru Inoue,et al.  Emission Spectra and Morphology of Carbon Films by ECR Plasma CVD , 1991 .

[14]  A. Mukhopadhyay,et al.  Young's modulus-porosity relationships for Si3N4 ceramics ― A critical evaluation , 1989 .

[15]  James C. Wang.  Young's modulus of porous materials , 1984 .

[16]  James C. Wang.  Young's modulus of porous materials , 1984 .

[17]  E. Case,et al.  Room-temperature fracture energy of monoclinic Gd2O3 , 1981 .

[18]  D. Hasselman,et al.  Non-recoverable elastic energy and crack propagation in brittle materials , 1972 .

[19]  D. J. Green,et al.  Fracture toughness of partially-sintered brittle materials , 1996 .

[20]  D. J. Green,et al.  Strength and Young's Modulus Behavior of a Partially Sintered Porous Alumina , 1995 .

[21]  F. Wéber,et al.  Mechanical properties in the initial stage of sintering , 1995, Journal of Materials Science.

[22]  A. A. Griffith.  The Phenomena of Rupture and Flow in Solids , 1921 .