Set point identification and robustness testing of electrostatic separation processes

Identification of the optimal operating conditions and evaluation of their robustness are critical issues for the industrial application of the electrostatic separation techniques. In spite of extensive investigations performed during recent years, no standard procedure is available for guiding the research of the set point and for minimizing the process sensibility to changes in certain critical factors. The aim of the present work is to formulate a set of recommendations regarding the choice of high-voltage, roll-speed, and feed-rate values for an important class of electrostatic separation applications: the selective sorting of conductive and nonconductive constituents of granular industrial wastes. The experiments were carried out on a laboratory separator, built by one of the authors, with various samples of chopped wire wastes furnished by ENICAB, Biskra, Algeria. Several one-factor-at-a-time followed by two factorial designs (one composite, the other fractional) were performed, based on the following three-step strategy: (1) identify the domain of variation of the controlled variables; (2) found the best choice of the set point; (3) asses the robustness, i.e; test whether the performance of the system remain satisfactory even when the factors vary slightly around that point. The results presented in this paper are strictly valid only for a well-defined category of processed materials, but a similar approach could be adopted for a wider range of electrostatic separation applications.

[1]  Lucian Dascalescu,et al.  Multiple-needle corona electrodes for electrostatic processes application , 1997, IAS '97. Conference Record of the 1997 IEEE Industry Applications Conference Thirty-Second IAS Annual Meeting.

[2]  Lucian Dascalescu,et al.  Electrostatic separation of brass from industrial wastes , 1996 .

[3]  Ranjit K. Roy,et al.  Design of Experiments Using The Taguchi Approach: 16 Steps to Product and Process Improvement , 2001 .

[4]  Rob Morrison,et al.  Development of electrostatic separation models for the mineral sands industry , 1991 .

[5]  Richard Craig Van Nostrand,et al.  Design of Experiments Using the Taguchi Approach: 16 Steps to Product and Process Improvement , 2002, Technometrics.

[6]  Lucian Dascalescu,et al.  Optimal high-voltage energization of corona-electrostatic separators , 1998 .

[7]  C. Ireland.  Fundamental concepts in the design of experiments , 1964 .

[8]  Lucian Dascalescu,et al.  High-voltage supplies for corona-electrostatic separators , 1995, IAS '95. Conference Record of the 1995 IEEE Industry Applications Conference Thirtieth IAS Annual Meeting.

[9]  Ion I. Inculet,et al.  ELECTROSTATIC SEPARATION OF PLASTICS FOR RECYCLING , 1998 .

[10]  L. Dascalescu,et al.  Charging of particulates in the corona field of roll-type electroseparators , 1994 .

[11]  Lucian Dascalescu,et al.  Factors which influence the insulation-metal electroseparation , 1993 .

[12]  L. Dascalescu,et al.  Electrostatic separation of muscovite mica from feldspathic pegmatites , 2001, Conference Record of the 2001 IEEE Industry Applications Conference. 36th IAS Annual Meeting (Cat. No.01CH37248).

[13]  R. Stephenson.  A and V , 1962, The British journal of ophthalmology.

[14]  J. I.  The Design of Experiments , 1936, Nature.

[15]  R. Carlson,et al.  Design of Experiments, Principles and Applications, L. Eriksson, E. Johansson, N. Kettaneh‐ Wold, C. Wikström and S. Wold, Umetrics AB, Umeå Learnways AB, Stockholm, 2000, ISBN 91‐973730‐0‐1, xii + 329 pp. , 2001 .

[16]  A. Iuga,et al.  Electrostatic separation of metals and plastics from granular industrial wastes , 1998, Conference Record of 1998 IEEE Industry Applications Conference. Thirty-Third IAS Annual Meeting (Cat. No.98CH36242).

[17]  Leonie Kohl,et al.  Fundamental Concepts in the Design of Experiments , 2000 .

[18]  L. Dascalescu,et al.  Optimization of electrostatic separation Processes using response surface modeling , 2004, IEEE Transactions on Industry Applications.

[19]  Ion I. Inculet,et al.  Electrostatic Mineral Separation , 1984 .

[20]  O. C. Ralston,et al.  Electrostatic separation of mixed granular solids , 1961 .

[21]  William C. Parr,et al.  Practical guide to experimental design , 1997 .

[22]  Lucian Dascalescu,et al.  Electrostatic separation of metals and plastics from granular industrial wastes , 2001 .

[23]  Lucian Dascalescu,et al.  ELECTROSTATIC SEPARATION OF INSULATING AND CONDUCTIVE PARTICLES FROM GRANULAR MIXES , 1998 .

[24]  Lucian Dascalescu,et al.  Charges and Forces on Conductive Particles in , 1995 .

[25]  Y. Higashiyama,et al.  RECENT PROGRESS IN ELECTROSTATIC SEPARATION TECHNOLOGY , 1998 .

[26]  L. Dascalescu,et al.  A linear-interaction model for electrostatic separation processes , 2002, Conference Record of the 2002 IEEE Industry Applications Conference. 37th IAS Annual Meeting (Cat. No.02CH37344).

[27]  Tim Stapenhurst,et al.  Taguchi Methods , 1990 .

[28]  A. Iuga,et al.  Computer-assisted experimental design for the optimization of electrostatic separation processes , 2000, Conference Record of the 2000 IEEE Industry Applications Conference. Thirty-Fifth IAS Annual Meeting and World Conference on Industrial Applications of Electrical Energy (Cat. No.00CH37129).