Dichlorodimethylsilane as an anti-stiction monolayer for MEMS: a comparison to the octadecyltrichlorosilane self-assembled monolayer

This paper presents a quantitative comparison of the dichlorodimethylsilane (DDMS) monolayer to the octade-cyltrichlorosilane (OTS) self-assembled monolayer (SAM) with respect to the film properties and their effectiveness as anti-stiction coatings for micromechanical structures. Both coatings have been evaluated in several ways, including atomic force microscopy (AFM), contact angle analysis (CAA), work of adhesion by cantilever beam array (CBA) technique and coefficient of static friction using a sidewall testing device. While water and hexadecane contact angles are comparable, the DDMS coated microstructures exhibit higher adhesion than OTS coated ones. Furthermore, coefficient of static friction data indicate that the DDMS films are not as effective at lubrication as the OTS SAMs are, although both exhibit much improvement over chemical oxide. However, AFM data show that the samples which receive DDMS treatment accumulate fewer particles during processing than those which receive the OTS SAM treatment. The thermal stability of the DDMS film in air far exceeds the OTS SAM, as the DDMS remains very hydrophobic to temperatures upwards of 400/spl deg/C.

[1]  Roger T. Howe,et al.  Alkene Based Monolayer Films As Anti Stiction Coatings For Polysilicon MEMS , 2001 .

[2]  R. Maboudian,et al.  Self-assembled monolayers as anti-stiction coatings for MEMS: characteristics and recent developments , 2000 .

[3]  Fernando Bitsie,et al.  Interferometric measurement for improved understanding of boundary effects in micromachined beams , 1999, Photonics West - Micro and Nano Fabricated Electromechanical and Optical Components.

[4]  Z. Rymuza.  Control tribological and mechanical properties of MEMS surfaces. Part 1: critical review , 1999 .

[5]  Terry A. Michalske,et al.  Accurate method for determining adhesion of cantilever beams , 1999 .

[6]  Kukjin Chun,et al.  A new class of surface modifiers for stiction reduction , 1999 .

[7]  R. Howe,et al.  Alkyltrichlorosilane-based self-assembled monolayer films for stiction reduction in silicon micromachines , 1998 .

[8]  T. Michalske,et al.  Adhesion of polysilicon microbeams in controlled humidity ambients , 1998 .

[9]  R. Maboudian.  Surface processes in MEMS technology , 1998 .

[10]  R. Maboudian,et al.  Thermal behavior of alkyl monolayers on silicon surfaces , 1997 .

[11]  C. Mastrangelo.  Adhesion-related failure mechanisms in micromechanical devices , 1997 .

[12]  Michael Thomas Dugger,et al.  Friction and wear in surface-micromachined tribological test devices , 1997, Photonics West - Micro and Nano Fabricated Electromechanical and Optical Components.

[13]  R. Howe,et al.  Critical Review: Adhesion in surface micromechanical structures , 1997 .

[14]  K. Komvopoulos.  Surface engineering and microtribology for microelectromechanical systems , 1996 .

[15]  R. Legtenberg,et al.  Stiction in surface micromachining , 1996 .

[16]  Ernest J. Garcia,et al.  Microfabricated actuators and their application to optics , 1995, Photonics West.

[17]  F. Rondelez,et al.  Silanization of Solid Substrates: A Step Toward Reproducibility , 1994 .

[18]  Roger T. Howe,et al.  The effect of release-etch processing on surface microstructure stiction , 1992, Technical Digest IEEE Solid-State Sensor and Actuator Workshop.

[19]  C. Mastrangelo,et al.  A simple experimental technique for the measurement of the work of adhesion of microstructures , 1992, Technical Digest IEEE Solid-State Sensor and Actuator Workshop.

[20]  Bharat Bhushan,et al.  Tribology and Mechanics of Magnetic Storage Devices , 1990 .