Large-Area Resistive Strain Sensing Sheet for Structural Health Monitoring

Damage significantly influences response of a strain sensor only if it occurs in the proximity of the sensor. Thus, two-dimensional (2D) sensing sheets covering large areas offer reliable early-stage damage detection for structural health monitoring (SHM) applications. This paper presents a scalable sensing sheet design consisting of a dense array of thin-film resistive strain sensors. The sensing sheet is fabricated using flexible printed circuit board (Flex-PCB) manufacturing process which enables low-cost and high-volume sensors that can cover large areas. The lab tests on an aluminum beam showed the sheet has a gauge factor of 2.1 and has a low drift of 1.5 μϵ/day. The field test on a pedestrian bridge showed the sheet is sensitive enough to track strain induced by the bridge’s temperature variations. The strain measured by the sheet had a root-mean-square (RMS) error of 7 μϵrms compared to a reference strain on the surface, extrapolated from fiber-optic sensors embedded within the bridge structure. The field tests on an existing crack showed that the sensing sheet can track the early-stage damage growth, where it sensed 600 μϵ peak strain, whereas the nearby sensors on a damage-free surface did not observe significant strain change.

[1]  Fu-Kuo Chang,et al.  Microfabricated Expandable Sensor Networks for Intelligent Sensing Materials , 2014, IEEE Sensors Journal.

[2]  Branko Glisic,et al.  Sensing sheets: Optimal arrangement of dense array of sensors for an improved probability of damage detection , 2015 .

[3]  Peipei Liu,et al.  Development of a PZT-based wireless digital monitor for composite impact monitoring , 2012 .

[4]  Filippo Ubertini,et al.  Dynamic Characterization of a Soft Elastomeric Capacitor for Structural Health Monitoring , 2015 .

[5]  Jerome P. Lynch,et al.  Carbon Nanotube Sensing Skins for Spatial Strain and Impact Damage Identification , 2009 .

[6]  Toshihiro Itoh,et al.  Printed strain sensor array for application to structural health monitoring , 2017 .

[7]  N. Kotov,et al.  Multifunctional layer-by-layer carbon nanotube–polyelectrolyte thin films for strain and corrosion sensing , 2007 .

[8]  Branko Glisic,et al.  Sensing sheet: the sensitivity of thin-film full-bridge strain sensors for crack detection and characterization , 2014 .

[9]  Jian Li,et al.  Concrete Crack Detection and Monitoring Using a Capacitive Dense Sensor Array , 2019, Sensors.

[10]  Branko Glisic,et al.  Crack detection and characterization techniques—An overview , 2014 .

[11]  Naveen Verma,et al.  Strain Sensing Sheets for Structural Health Monitoring Based on Large-Area Electronics and Integrated Circuits , 2016, Proceedings of the IEEE.

[12]  Hwasoo Yeo,et al.  A comparative study of time-based maintenance and condition-based maintenance for optimal choice of maintenance policy , 2016 .

[13]  Toshihiro Itoh,et al.  Printed strain sensor with temperature compensation and its evaluation with an example of applications in structural health monitoring , 2017 .

[14]  Gangbing Song,et al.  Wind turbine blade health monitoring with piezoceramic-based wireless sensor network , 2013 .

[15]  Naveen Verma,et al.  Strain Transfer for Optimal Performance of Sensing Sheet , 2017, Sensors.

[16]  이태식,et al.  지속적 발전을 위한 한국형 Infrastructure Report Card 개발 , 2008 .

[17]  Ian F. C. Smith,et al.  Exploring potential benefits of bridge condition assessment in highway operations , 2019, IABSE Congress, New York, New York 2019: The Evolving Metropolis.

[18]  Simon Laflamme,et al.  A large-area strain sensing technology for monitoring fatigue cracks in steel bridges , 2017 .

[19]  Filippo Ubertini,et al.  Experimental wind tunnel study of a smart sensing skin for condition evaluation of a wind turbine blade , 2017 .

[20]  Robert D. Adams,et al.  Development of a dilatometer and measurement of the shrinkage behaviour of adhesives during cure , 2013 .

[21]  Keith Worden,et al.  An introduction to structural health monitoring , 2007, Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences.

[22]  Yongan Huang,et al.  Impact Monitoring for Aircraft Smart Composite Skins Based on a Lightweight Sensor Network and Characteristic Digital Sequences , 2018, Sensors.

[23]  B. Culshaw,et al.  Acousto-ultrasonic sensing using fiber Bragg gratings , 2003 .

[24]  António Barrias,et al.  A Review of Distributed Optical Fiber Sensors for Civil Engineering Applications , 2016, Sensors.

[25]  Liang Chen,et al.  Recent Progress in Distributed Fiber Optic Sensors , 2012, Sensors.

[26]  Satish Nagarajaiah,et al.  Strain paint: noncontact strain measurement using single-walled carbon nanotube composite coatings. , 2012, Nano letters.

[27]  N. Kotov,et al.  Tailoring Piezoresistive Sensitivity of Multilayer Carbon Nanotube Composite Strain Sensors , 2008 .

[28]  T. Itoh,et al.  Printed strain sensors for early damage detection in engineering structures , 2018 .

[29]  Gongkang Fu,et al.  Bridge Management Using Pontis and Improved Concepts , 2014 .

[30]  Yi-Qing Ni,et al.  Integrating bridge structural health monitoring and condition-based maintenance management , 2012 .

[31]  Branko Glisic,et al.  Identifying Time Periods of Minimal Thermal Gradient for Temperature-Driven Structural Health Monitoring , 2018, Sensors.

[32]  Y. Y. Li,et al.  Hypersensitivity of strain-based indicators for structural damage identification: A review , 2010 .

[33]  Simon Laflamme,et al.  Soft Elastomeric Capacitor Network for Strain Sensing Over Large Surfaces , 2013, IEEE/ASME Transactions on Mechatronics.

[34]  M. J. Sundaresan,et al.  Smart Sensor System for Structural Condition Monitoring of Wind Turbines: 30 May 2002--30 April 2006 , 2006 .

[35]  Mohammad Pour-Ghaz,et al.  Electrical impedance tomography-based sensing skin for quantitative imaging of damage in concrete , 2014 .

[36]  Chao Hu,et al.  Optimal sensor placement within a hybrid dense sensor network using an adaptive genetic algorithm with learning gene pool , 2018 .

[37]  Ben C. Gerwick,et al.  Substructures of Major Overwater Bridges , 2014 .

[38]  M. Robinson.  Strain gage materials processing, metallurgy, and manufacture , 2006 .

[39]  Zhongyi Sheng,et al.  The piezoresistance coefficients of copper and copper-nickel alloys , 2000 .

[40]  Steven D. Glaser,et al.  A hybrid wireless sensor network for acoustic emission testing in SHM , 2008, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[41]  L. Battisti,et al.  Photonic crystals for monitoring fatigue phenomena in steel structures , 2009, Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.