Experiences with Modeling Friction in Composite Bolted Joints

Finite element analyses of composite bolted joints are common in the literature. However, the important issue of friction is often given superficial treatment. Friction introduces added difficulties to an already complex contact problem in terms of numerical convergence, and there can be a temptation to accept any method that will give a convergent solution. However, friction can significantly alter the stress distribution in the laminate at the bolt-hole interface, and carries a major proportion of the load in torqued joints; hence is important to model correctly. In the present study, experiences with modeling friction in composite bolted joints using commercial code MSC.Marc are presented. Unlike previous studies, both physical friction parameters and nonphysical convergence parameters within the available models are examined in detail and the findings should be helpful to other researchers analyzing similar problems. Two available models within the code are examined for their ability to model load transfer by friction in torqued joints, and the stress distribution at the bolt-hole interface in a pinned joint. The torqued joints include a large clearance so that both static and kinetic friction effects occur as the joint begins to slide and clearance is taken up. Results from the torqued joint models are compared with the experimental results. The stress distribution at the bolt-hole interface of the pinned joint is compared with a solution from an analytical method. It has been found that only one of the two models available in the code is capable of producing satisfactory results, and even with that model significant modification to the default friction parameters was required. It has also been found that using friction coefficients measured under ideal (clean) conditions in the model of the torqued joints did not give very good agreement with the joint experiments, which involved routine handling of the specimens. Finally, the developed friction model is used in a case study of a multibolt joint with variable degrees of bolt torque and bolt-hole clearances, and it is shown that such models can provide useful information for the design of composite bolted joints.

[1]  F. L. Matthews,et al.  A Progressive Damage Model for Mechanically Fastened Joints in Composite Laminates , 1999 .

[2]  Michael A. McCarthy.  BOJCAS: Bolted joints in composite aircraft structures , 2001 .

[3]  Bart Vangrimde,et al.  Analysis of the bearing response test for polymer matrix composite laminates: bearing stiffness measurement and simulation , 2002 .

[4]  M. A. McCarthy,et al.  Bolt-hole clearance effects and strength criteria in single-bolt, single-lap, composite bolted joints , 2002 .

[5]  S. Kim,et al.  Finite element analysis of laminated composite plates with multi-pin joints considering friction , 1995 .

[6]  N. Ohmae,et al.  Chapter 7 - Friction and Wear Performance of Unidirectionally Oriented Glass, Carbon, Aramid and Stainless Steel Fiber-Reinforced Plastics , 1986 .

[7]  D. E. Cooper,et al.  The Effects of Pin Elasticity, Clearance, and Friction on the Stresses in a Pin-Loaded Orthotropic Plate , 1987 .

[8]  J. T. Mottram,et al.  Finite Element Analysis of Non-Laminated Composite Pin-Loaded Straps for Civil Engineering , 2001 .

[9]  M. A. McCarthy,et al.  Finite element analysis of effects of clearance on single shear composite bolted joints , 2003 .

[10]  T. S. Ramamurthy.  New studies on the effect of bearing loads in lugs with clearance fit pins , 1989 .

[11]  Joakim Schön,et al.  Coefficient of friction and wear of a carbon fiber epoxy matrix composite , 2004 .

[12]  M. A. McCarthy,et al.  Three-dimensional finite element analysis of single-bolt, single-lap composite bolted joints: part I—model development and validation , 2005 .

[13]  Tomas Ireman,et al.  Three-dimensional stress analysis of bolted single-lap composite joints , 1998 .

[14]  Byung Man Kwak,et al.  Contact analysis of mechanically fastened joints in composite laminates by linear complementarity problem formulation , 1997 .

[15]  K. Friedrich,et al.  Friction and wear of polymer composites , 1986 .

[16]  Th.B. Kermanidis,et al.  A three‐dimensional progressive damage model for bolted joints in composite laminates subjected to tensile loading , 2001 .

[17]  P. D. Herrington,et al.  Factors affecting the friction coefficients between metallic washers and composite surfaces , 1991 .

[18]  J. C. Simo,et al.  A perturbed Lagrangian formulation for the finite element solution of contact problems , 1985 .

[19]  Joakim Schön,et al.  Coefficient of friction for aluminum in contact with a carbon fiber epoxy composite , 2004 .

[20]  Joakim Schön,et al.  Quasi-static behaviour of composite joints with protruding-head bolts , 2001 .

[21]  M. A. McCarthy,et al.  Three-dimensional finite element analysis of single-bolt, single-lap composite bolted joints: Part II––effects of bolt-hole clearance , 2005 .

[22]  Fabrice Pierron,et al.  A Numerical and Experimental Study of Woven Composite Pin-Joints , 2000 .

[23]  J. Oden,et al.  Nonlocal and Nonlinear Friction Laws and Variational Principles for Contact Problems in Elasticity , 1983 .

[24]  M. A. McCarthy,et al.  BOLJAT: a tool for designing composite bolted joints using three-dimensional finite element analysis , 2002 .

[25]  G. N. Labeas,et al.  Strength prediction of bolted joints in graphite/epoxy composite laminates , 2002 .