Optimization of thermoelectric heat pumps by operating condition management and heat exchanger design

Abstract This paper introduces an optimization method for improving thermoelectric heat pump performance by operating condition management of the thermoelectric modules (TEMs) and design optimization of the heat exchangers linked to the TEMs. The device studied, corresponding to an original configuration of the thermoelectric heat pump, comprises two commercial thermoelectric modules and two mini-channel heat sinks through which water flows, in contact with both sides of the TEMs. The objective function is the maximization of the device’s coefficient of performance (COP), including the electrical and mechanical consumption of the thermoelectric modules and the circulating auxiliaries. First, the optimization variables are the number and the diameter of mini-channels, and the mass flows for both heat sinks (hot and cold sides). The results show that similar results are obtained by minimization of the entropy generation in the device. Finally, the hot thermal power demand is included in the optimization variables for complete optimization of the device. The results of full optimization converge with those obtained with the previous partial optimization.

[1]  D. Rowe.  CRC Handbook of Thermoelectrics , 1995 .

[2]  Lingai Luo,et al.  Constructal optimization of arborescent structures with flow singularities , 2009 .

[3]  P. G. Lau,et al.  Economic optimization of heat sink design , 2008 .

[4]  Gary Rosengarten,et al.  Integrated microthermoelectric cooler for microfluidic channels , 2006 .

[5]  V. Torczon,et al.  Direct search methods: then and now , 2000 .

[6]  Ook Joong Kim,et al.  Analysis on the cooling performance of the thermoelectric micro-cooler , 2007 .

[7]  William Thomson,et al.  4. On a Mechanical Theory of Thermo-Electric Currents , 1857 .

[8]  D. Infield,et al.  Design optimization of thermoelectric devices for solar power generation , 1998 .

[9]  Henry Darcy.  Recherches expérimentales relatives au mouvement de l'eau dans les tuyaux , 1857 .

[10]  Selahatti̇n Göktun,et al.  Design considerations for a thermoelectric refrigerator , 1995 .

[11]  Lingai Luo,et al.  Flow distribution and pressure drop in 2D meshed channel circuits , 2011 .

[12]  L. Falk,et al.  Rapid design of channel multi-scale networks with minimum flow maldistribution , 2009 .

[13]  Lingai Luo,et al.  Flow and pressure distribution in linear discrete “ladder-type” fluidic circuits: An analytical approach , 2011 .

[14]  C. B. Vining,et al.  Semiconductors are cool , 2001, Nature.

[15]  R. Shah.  Laminar Flow Forced convection in ducts , 1978 .

[16]  G. Jackson,et al.  Optimization of cross flow heat exchangers for thermoelectric waste heat recovery , 2004 .

[17]  Adrian Bejan,et al.  General criterion for rating heat-exchanger performance , 1978 .

[18]  N. P. Kikas.  Laminar flow distribution in solar systems , 1995 .

[19]  L. Luo,et al.  Uniform flows in rectangular lattice networks , 2011 .

[20]  Reiyu Chein,et al.  Performances of thermoelectric cooler integrated with microchannel heat sinks , 2005 .

[21]  Achille Messac,et al.  Design of thermoelectric heat pump unit for active building envelope systems , 2005 .

[22]  Julius Ludwig Weisbach,et al.  Lehrbuch der Ingenieur= und Maschinen=Mechanik , 1855 .

[23]  Fengrui Sun,et al.  Heat transfer effect on the specific cooling load of refrigerators , 1996 .

[24]  Gao Min,et al.  Improved model for calculating the coefficient of performance of a Peltier module , 2000 .

[25]  Maria Telkes,et al.  The Efficiency of Thermoelectric Generators. I. , 1947 .

[26]  Adrian Bejan,et al.  Method of entropy generation minimization, or modeling and optimization based on combined heat transfer and thermodynamics , 1996 .