MECHANICAL MODELS OF FRACTURE REACTIVATION AND SLIP ON BEDDING SURFACES DURING FOLDING OF THE ASYMMETRIC ANTICLINE AT SHEEP MOUNTAIN, WYOMING

Abstract We use finite element methods to investigate the reactivation of fractures (opening and shearing) and the development of bedding-surface slip during the deformation of the asymmetric anticline at Sheep Mountain, Wyoming. A series of numerical simulations were run to show the effect of mechanical stratigraphy, layer thickness, slip on bedding surfaces, and tectonic shortening of the fold on the response of a representative three-layer (ductile, brittle, ductile) two-dimensional system. The model uses large deformation frictional contact mechanics to capture the response of existing fractures and slip along bedding surfaces, and considers both elastic and elastoplastic layer properties. The computational results demonstrate the relationships among overall configuration of the multilayer, slip on bedding surfaces, and the sequence and mode of deformation (opening versus shearing) of bed-perpendicular fractures. We show that fractures located in the hinge are mainly reactivated as joints and that those in the forelimb are predominantly reactivated as thrust faults. A flexural-slip mechanism develops during folding when the layers bounded by frictional bedding surfaces have similar stiffnesses. In contrast, when the difference in the layer stiffnesses is significant (softer outer layers) the deformation is accommodated within the softer units without exceeding the frictional strength of the bedding surfaces. A reduction of the middle layer thickness from 100 m to 10 m has a minor quantitative effect on the slip along the bedding surfaces. We compare the numerical results with fracture data collected at Sheep Mountain Anticline, and discuss the similarities and differences between the field observations and the model results.

[1]  Ronaldo I. Borja,et al.  On the numerical integration of three-invariant elastoplastic constitutive models , 2003 .

[2]  T. S. Daltaban,et al.  Structural Geology in Reservoir Characterization , 1998 .

[3]  Arvid M. Johnson,et al.  Localization of layer-parallel faults in San Rafael swell, Utah and other monoclinal folds , 2000 .

[4]  Teruo Nakai,et al.  STRESS-DEFORMATION AND STRENGTH CHARACTERISTICS OF SOIL UNDER THREE DIFFERENT PRINCIPAL STRESSES , 1974 .

[5]  P. Wriggers.  Finite element algorithms for contact problems , 1995 .

[6]  J. C. Jaeger,et al.  Fundamentals of rock mechanics , 1969 .

[7]  F. Bastida,et al.  On tangential longitudinal strain folding , 2000 .

[8]  M. S. Wilkerson,et al.  Predicting the orientation of joints from fold shape: Results of pseudo–three-dimensional modeling and curvature analysis , 2000 .

[9]  Atilla Aydin,et al.  Unweaving the joints in Entrada Sandstone, Arches National Park, Utah, U.S.A. , 1995 .

[10]  Ronaldo I. Borja,et al.  Mechanical aspects of thrust faulting driven by far-field compression and their implications for fold geometry , 2007 .

[11]  S. M. Willson,et al.  Predictive modelling of structure evolution in sandbox experiments , 2006 .

[12]  Y. Leroy,et al.  Mechanical constraints on the chronology of fracture activation in folded Devonian sandstone of the western Moroccan Anti-Atlas , 2003 .

[13]  George V. Chilingar,et al.  Faulting, fault sealing and fluid flow in hydrocarbon reservoirs. , 2000 .

[14]  R. Butler,et al.  Modelling approaches to understanding fold development: implications for hydrocarbon reservoirs , 2004 .

[15]  R. Carmichael.  CRC handbook of physical properties of rocks , 1982 .

[16]  Sheep Mountain: Backlimb Tightening and Sequential Deformation in the Bighorn Basin, Wyoming , 2003 .

[17]  F. Niño,et al.  The role of bed-parallel slip in the formation of blind thrust faults , 1998 .

[18]  R. Rioux.  Geology of the Spence-Kane Area, Big Horn County, Wyoming , 1958 .

[19]  S. Treagus.  Strain refraction in layered systems , 1988 .

[20]  M. Cooke,et al.  Bedding-plane slip in initial stages of fault-related folding , 1997 .

[21]  M. Deighton.  Fracture of Brittle Solids , 1976 .

[22]  L. Strayer,et al.  Numerical modeling of fold initiation at thrust ramps , 1997 .

[23]  Michele L. Cooke,et al.  Fracture termination and step-over at bedding interfaces due to frictional slip and interface opening , 2001 .

[24]  J. Suppe,et al.  Initiation and reactivation of faults during movement over a thrust-fault ramp: numerical mechanical models , 2001 .

[25]  Z. Bieniawski.  Determining rock mass deformability: experience from case histories , 1978 .

[26]  T. Laursen.  Computational Contact and Impact Mechanics , 2003 .

[27]  M. Cooke,et al.  Interlayer slip and joint localization in the East Kaibab Monocline, Utah: field evidence and results from numerical modelling , 1999, Geological Society, London, Special Publications.

[28]  W. Haneberg.  Faults and subsurface fluid flow in the shallow crust , 1999 .

[29]  David D. Pollard,et al.  Numerical simulation of fracture set formation: A fracture mechanics model consistent with experimental observations , 1994 .

[30]  Robert Ladd.  The geology of Sheep Canyon Quadrangle: Wyoming , 1979 .

[31]  D. Fisher,et al.  Kinematic analysis of a large-scale leading edge fold, Lost River Range, Idaho , 1994 .

[32]  Arvid M. Johnson,et al.  Opposite senses of fold asymmetry , 1989 .

[33]  D. Pollard,et al.  Progress in understanding jointing over the past century , 1988 .

[34]  J. C. Simo,et al.  Consistent tangent operators for rate-independent elastoplasticity☆ , 1985 .

[35]  J. Cosgrove,et al.  Forced Folds and Fractures , 2000 .

[36]  D. Pollard,et al.  Explanation for fracture spacing in layered materials , 2000, Nature.

[37]  M. Fischer,et al.  The geometric evolution of foreland thrust systems , 1992 .

[38]  Derrell A. Smith.  Theoretical Considerations of Sealing and Non-Sealing Faults , 1966 .

[39]  F. Maerten,et al.  Chronologic modeling of faulted and fractured reservoirs using geomechanically based restoration: Technique and industry applications , 2006 .

[40]  D. Pollard,et al.  Fracture spacing in layered rocks: a new explanation based on the stress transition , 2000 .

[41]  W. Jamison,et al.  Viscous-plastic finite-element models of fault-bend folds , 1995 .

[42]  C. Nevin,et al.  Principles of Structural Geology , 1932, Nature.

[43]  A. K. Dubey,et al.  Variation of interlayer slip in space and time during flexural folding , 1980 .

[44]  Yves M. Leroy,et al.  Activation of diffuse discontinuities and folding of sedimentary layers , 2003 .

[45]  T. Engelder,et al.  Joint development normal to regional compression during flexural-flow folding: the Lilstock buttress anticline, Somerset, England , 2001 .

[46]  Mechanisms for Deformation of Sedimentary Strata at Sheep Mountain Anticline, Bighorn Basin, Wyoming , 1983 .

[47]  Atilla Aydin,et al.  Fractures, faults, and hydrocarbon entrapment, migration and flow , 2000 .

[48]  Guozhu Zhao,et al.  Analysis of minor fractures associated with joints and faulted joints , 1991 .

[49]  Peter Wriggers,et al.  Computational Contact Mechanics , 2002 .

[50]  Louis Moresi,et al.  A director theory for visco-elastic folding instabilities in multilayered rock , 2002 .

[51]  R. Groshong.  Folding of viscous layers , 1997 .

[52]  S. Bourne.  Contrast of elastic properties between rock layers as a mechanism for the initiation and orientation of tensile failure under uniform remote compression , 2003 .

[53]  Structural Interpretation of Sheep Mountain Anticline, Bighorn Basin, Wyoming , 1996 .

[54]  J. Ramsay.  Development of Chevron Folds , 1974 .

[55]  A. A. Griffith.  The Phenomena of Rupture and Flow in Solids , 1921 .

[56]  J. C. Simo,et al.  A continuum-based finite element formulation for the implicit solution of multibody, large deformation-frictional contact problems , 1993 .

[57]  Allan Cox,et al.  Relative Motions Between Oceanic and Continental Plates in the Pacific Basin , 1986 .

[58]  Ronaldo I. Borja,et al.  Conditions for instabilities in collapsible solids including volume implosion and compaction banding , 2006 .

[59]  David R. Owen,et al.  Benchmarks for the evolution of shear localisation with large relative sliding in frictional materials , 2006 .

[60]  Andrew V. Wolfsberg,et al.  Rock Fractures and Fluid Flow: Contemporary Understanding and Applications , 1997 .

[61]  Michael A. Wacker,et al.  Faulted joints: kinematics, displacement-length scaling relations and criteria for their identification , 2001 .

[62]  P. Bird.  Stress direction history of the western United States and Mexico since 85 Ma , 2002 .

[63]  T. Engelder,et al.  Joint initiation in bedded clastic rocks , 2001 .

[64]  N. Culshaw,et al.  Flexural-slip folding in the Meguma Group, Nova Scotia, Canada , 2001 .

[65]  D. Pollard,et al.  The role of fractures in the structural interpretation of Sheep Mountain Anticline, Wyoming , 2006 .

[66]  G. Couples,et al.  Effects of interlayer slip in model forced folds , 1999, Geological Society, London, Special Publications.