A comparative hydrodynamic study of two types of spouted bed reactor designs

In order to properly design and scale up spouted beds, one needs to predict the minimum spouting velocity of specific systems having different bed dimensions, and properties of particle and spouting gas. Because of inherent complexity of predicting minimum spouting velocity, the prevailing approach has been to use empirical correlations, a number of which are available in the literature. Central jet distributors are commonly used in the experimental studies reported in the literature. Circular slit distributor is a new concept in which air is supplied to the bed of particles through a circular slit. This paper presents results of an experimental study on the hydrodynamics of central jet and circular slit distributors. In this paper a fully connected feed-forward neural network model was used to predict the minimum spouting velocity of central jet and circular slit spouted beds. A neural network model was also developed to predict minimum fluidization velocity. The actual experimental data obtained from published literature and from the experiments carried out in this study were used for training and validating the models. The minimum spouting and fluidization velocities predicted using the neural network models developed in this study show a better approximation to the actual experimental values than those obtained from correlations available in the open literature. The position of flow regime of circular slit spouted bed was also established relative to the flow regimes of central jet spouted bed and fluidized bed.

[1]  M. H. Morgan,et al.  Spout voidage distribution, stability and particle circulation rates in spouted beds of coarse particles—I. Theory , 1985 .

[2]  J. F. Richardson,et al.  Velocity-voidage relations for sedimentation and fluidisation , 1979 .

[3]  Liang-Shih Fan,et al.  Characteristics of fluidization at high pressure , 1984 .

[4]  Chi Hau Chen,et al.  Fuzzy logic and neural network handbook , 1996 .

[5]  B. D. Bowen,et al.  Spout diameter variation in two-dimensional and cylindrical spouted beds: a theoretical models and its verification , 1989 .

[6]  Soteris A. Kalogirou,et al.  Artificial neural networks used for the performance prediction of a thermosiphon solar water heater , 1999 .

[7]  H. A. Becker.  An investigation of laws governing the spouting of coarse particles , 1961 .

[8]  M. H. Morgan,et al.  Measurements of spout voidage distributions, particle velocities and particle circulation rates in spouted beds of coarse particles—II. Experimental verification , 1987 .

[9]  Efraim Turban,et al.  Decision support and expert systems , 1993 .

[10]  Gad Hetsroni,et al.  Handbook of multiphase systems , 1982 .

[11]  B. Yegnanarayana,et al.  Artificial Neural Networks , 2004 .

[12]  John R. Grace,et al.  Scale-up studies of spouted beds , 1997 .

[13]  K. B. Mathur,et al.  A technique for contacting gases with coarse solid particles , 1955 .

[14]  H. Littman.  A theory for predicting the maximum spoutable height in a spouted bed , 1977 .

[15]  Javier Bilbao,et al.  Pressure drop in conical spouted beds , 1993 .

[16]  A. Çeçen.  The maximum spoutable bed heights of fine particles spouted with air , 1994 .

[17]  J. Arnaldos,et al.  Improved equation for the calculation of minimum fluidization velocity , 1986 .

[18]  C. Wen.  Mechanics of Fluidization , 1966 .

[19]  Norman Epstein,et al.  HYDRODYNAMICS OF SPOUTED BEDS AT ELEVATED TEMPERATURES , 1987 .

[20]  John R. Grace,et al.  Gas phase solid-catalysed chemical reaction in spouted beds , 1983 .

[21]  Axel Meisen,et al.  Hydrodynamics of shallow, conical spouted beds , 1992 .

[22]  P. Grenier,et al.  The ratio of terminal velocity to minimum fluidising velocity for spherical particles , 1968 .

[23]  N. Hiquily,et al.  Vitesse minimale de fluidisation et expansion des couches fluidisées par un gaz , 1984 .

[24]  Cláudio Augusto Oller do Nascimento,et al.  Minimum air requirement for spouting mixed particles , 1974 .

[25]  Hugo S. Caram,et al.  Solid flow in the annular region of a spouted bed , 1989 .

[26]  M. A. Malek,et al.  Pressure Drop and Spoutable Bed Height in Spouted Beds , 1965 .

[27]  G A Lefroy,et al.  THE MECHANICS OF SPOUTED BEDS , 1969 .

[28]  J. Grace.  Contacting modes and behaviour classification of gas—solid and other two-phase suspensions , 1986 .

[29]  G. Suciu,et al.  Phase distribution and residence time in a spouted bed , 1977 .

[30]  Norman Epstein,et al.  Data and models for flow distribution and pressure drop in spouted beds , 1978 .

[31]  Osamu Uemaki,et al.  Particle segregation in a spouted bed of binary mixtures of particles , 1983 .

[32]  S. Toyama,et al.  An experimental investigation of minimum fluidization velocity at elevated temperatures and pressures , 1985 .