Effect of the Geometrical Constraints to the Wenner Four-Point Electrical Resistivity Test of Reinforced Concrete Slabs

The main objectives of this study are to evaluate the effect of geometrical constraints of plain concrete and reinforced concrete slabs on the Wenner four-point concrete electrical resistivity (ER) test through numerical and experimental investigation and to propose measurement recommendations for laboratory and field specimens. First, a series of numerical simulations was performed using a 3D finite element model to investigate the effects of geometrical constraints (the dimension of concrete slabs, the electrode spacing and configuration, and the distance of the electrode to the edges of concrete slabs) on ER measurements of concrete. Next, a reinforced concrete slab specimen (1500 mm (width) by 1500 mm (length) by 300 mm (thickness)) was used for experimental investigation and validation of the numerical simulation results. Based on the analytical and experimental results, it is concluded that measured ER values of regularly shaped concrete elements are strongly dependent on the distance-to-spacing ratio of ER probes (i.e., distance of the electrode in ER probes to the edges and/or the bottom of the concrete slabs normalized by the electrode spacing). For the plain concrete, it is inferred that the thickness of the concrete member should be at least three times the electrode spacing. In addition, the distance should be more than twice the electrode spacing to make the edge effect almost negligible. It is observed that the findings from the plain concrete are also valid for the reinforced concrete. However, for the reinforced concrete, the ER values are also affected by the presence of reinforcing steel and saturation of concrete, which could cause disruptions in ER measurements.

[1]  Steve Millard,et al.  REINFORCED CONCRETE RESISTIVITY MEASUREMENT TECHNIQUES. , 1991 .

[2]  Jiang-Jhy Chang,et al.  The effects of specimen parameters on the resistivity of concrete , 2014 .

[3]  Patrick Icenogle,et al.  Surface Resistivity Measurements Evaluated as Alternative to Rapid Chloride Permeability Test for Quality Assurance and Acceptance , 2012 .

[4]  Erik J. Sellevold,et al.  Electrical resistivity of concrete , 1995 .

[5]  W. López,et al.  Influence of the degree of pore saturation on the resistivity of concrete and the corrosion rate of steel reinforcement , 1993 .

[6]  J. Bullard,et al.  Factors that Influence Electrical Resistivity Measurements in Cementitious Systems , 2013 .

[7]  S. Tangtermsirikul,et al.  Effects of Concrete Mix Proportion on Electrical Resistivity of Concrete , 2016 .

[8]  Odd E. Gjørv,et al.  Electrical Resistivity Measurements for Quality Control During Concrete Construction , 2008 .

[9]  H. Rajaie,et al.  Comparison of Four Electrical Measurement Methods with Bulk Diffusion for Assessing the Chloride Resistance of Concretes , 2016 .

[10]  I. Yoon.  Effect of Water and Chloride Content on Electrical Resistivity in Concrete , 2016 .

[11]  Ethiopia Nigussie,et al.  Internet of Things based Durability Monitoring and Assessment of Reinforced Concrete Structures , 2019, Procedia Computer Science.

[12]  Jinlong Pan,et al.  Electrical resistivity of fly ash and metakaolin based geopolymers , 2020 .

[13]  Rishi Gupta,et al.  Electrical Resistivity of Concrete for Durability Evaluation: A Review , 2017 .

[14]  Bo Yu,et al.  Probabilistic evaluation method for corrosion risk of steel reinforcement based on concrete resistivity , 2017 .

[15]  Sanjeev Kumar Verma,et al.  Monitoring Corrosion of Steel Bars in Reinforced Concrete Structures , 2014, TheScientificWorldJournal.

[16]  D. Babor,et al.  Environmental Impact of Concrete , 2009 .

[17]  Michael Raupach,et al.  Test methods for on site measurement of resistivity of concrete , 2000 .

[18]  J. M. Garza,et al.  In-Place Resistivity of Bridge Deck Concrete Mixtures , 2009 .

[19]  Gita Charmchi.  The Role of Concrete Maturity in Resistivity-Based Performance Specifications , 2015 .

[20]  Steve Millard,et al.  Measurement of concrete resistivity for assessment of corrosion severity of steel using wenner technique , 1999 .

[21]  Susanto Teng,et al.  Durability of Very-High-Strength Concrete with Supplementary Cementitious Materials for Marine Environments , 2016 .

[22]  L. Bertolini,et al.  Concrete resistivity and reinforcement corrosion rate as a function of temperature and humidity of the environment , 1997 .

[23]  Jurng-Jae Yee,et al.  Electrical Resistivity Measurements of Reinforced Concrete Slabs with Delamination Defects , 2020, Sensors.

[24]  Shamsad Ahmad.  An experimental study on correlation between concrete resistivity and reinforcement corrosion rate , 2014 .

[25]  M. Vazquez,et al.  Chloride induced corrosion of reinforcing steel evaluated by concrete resistivity measurements , 2004 .

[26]  Mohammad Shekarchi,et al.  Environmental assessment of green concrete containing natural zeolite on the global warming index in marine environments , 2014 .

[27]  J. M. Miranda,et al.  Considerations on reproducibility of potential and corrosion rate measurements in reinforced concrete , 2004 .

[28]  M Hunger,et al.  Long-term chloride migration coefficient in slag cement-based concrete and resistivity as an alternative test method , 2016 .

[29]  O. Sengul.  Use of electrical resistivity as an indicator for durability , 2014 .

[30]  M. Alexander,et al.  Resistivity-based chloride-induced corrosion rate prediction models and hypothetical framework for interpretation of resistivity measurements in cracked RC structures , 2016 .

[31]  Pouria Ghods,et al.  Numerical investigation of the role of embedded reinforcement mesh on electrical resistivity measurements of concrete using the Wenner probe technique , 2016 .

[33]  John Benjamin Dryden,et al.  Precision Statements for the Surface Resistivity of Water Cured Concrete Cylinders in the Laboratory , 2012 .

[34]  F. Presuel-Moreno,et al.  Normalization of Temperature Effect on Concrete Resistivity by Method Using Arrhenius Law , 2014 .

[35]  D. J. Naus,et al.  Durability of building materials and components) , 1990 .

[36]  Javier Sánchez,et al.  Modification of four point method to measure the concrete electrical resistivity in presence of reinforcing bars , 2014 .

[37]  Alberto A. Sagüés,et al.  Practical evaluation of resistivity of concrete in test cylinders using a Wenner array probe , 1996 .

[38]  C. Andrade,et al.  Relationship between conductivity of concrete and corrosion of reinforcing bars , 1989 .

[39]  Christoph Gehlen,et al.  Electrolytic resistivity of cover concrete: Relevance, measurement and interpretation , 1999 .

[40]  Tommy Nantung,et al.  Variability Analysis of the Bulk Resistivity Measured Using Concrete Cylinders , 2012 .

[41]  Duncan Herfort,et al.  Sustainable Development and Climate Change Initiatives , 2008 .

[42]  A. Alhozaimy,et al.  Electro-chemical investigation for the effect of rebar source and surface condition on the corrosion rate of reinforced concrete structures under varying corrosive environments , 2020 .

[43]  Claus K. Larsen,et al.  Compilation of 5 papers on (1) Electrical resistivity as a durability indicator and (2) Cracking tendency in hardening concrete , 2007 .

[44]  Colin Gagg,et al.  Cement and concrete as an engineering material: an historic appraisal and case study analysis , 2014 .

[45]  Luca Bertolini,et al.  Effects of Nanosilica on Compressive Strength and Durability Properties of Concrete with Different Water to Binder Ratios , 2016 .

[46]  S. Yilmaz.  The geometric resistivity correction factor for several geometrical samples , 2015 .

[47]  Alain Denis,et al.  Non-destructive evaluation of cracks in massive concrete using normal dc resistivity logging , 2014 .

[48]  Odd E. Gjørv,et al.  Effect of Embedded Steel on Electrical Resistivity Measurements on Concrete Structures , 2009 .