Implementation of a Voltage Multiplier Integrated HID Ballast Circuit With Dimming Control for Automotive Application

High-intensity discharge (HID) lamps are becoming popular substitutes for halogen lamps in automotive headlamps because of the high lumen/watt ratio and the color of the light. In this paper, a ballast (integrated with a voltage multiplier circuit in the secondary winding of the dc converter transformer) with dimming control is presented. The proposed circuit not only eliminates one auxiliary winding but also reduces the voltage across the switch on the primary side and consequently permits the selection of switches with a lower rating. A brief review of the HID circuits is done and compared with the proposed circuit. Experimental results from the prototype are presented. This paper also presents different methods of dimming the automotive HID lamps based on analog and digital control and discusses the relative merits of each of the methods. The dimming control is implemented using both the methods, and experimental results are presented. It is envisaged that the dimming control will provide some flexibility to drivers in the control of HID lamps to suit the driving conditions in the modern cities that are very well lit at night. This paper investigates the merits of each method and discusses the practical issues for implementing such controls.

[1]  M. Rico,et al.  Analysis, design, and optimization of the LCC resonant inverter as a high-intensity discharge lamp ballast , 1998 .

[2]  Alberto Reatti,et al.  Low-cost high power-density electronic ballast for automotive HID lamp , 2000 .

[3]  K.W.E. Cheng,et al.  Study of Dimming Control Methods For HID Automotive Lamps , 2006, 2006 2nd International Conference on Power Electronics Systems and Applications.

[4]  Henry Shu-Hung Chung,et al.  A comparative study on dimming control methods for electronic ballasts , 2001 .

[5]  Dianguo Xu,et al.  Dimmable Electronic Ballast for 250W HPS Lamp in Street Lighting with Analog Dimming Interface Circuit , 2007, APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition.

[6]  H. Witting.  Acoustic resonances in cylindrical high‐pressure arc discharges , 1978 .

[7]  Hiroshi Nishimura,et al.  A Study of HID Lamp Life when Operated by Electronic Ballasts , 1995 .

[8]  Henry Shu-Hung Chung,et al.  An electronic ballast with wide dimming range, high PF, and low EMI , 2001 .

[9]  A.J. Calleja,et al.  Evaluation of a novel single-stage high-power-factor electronic ballast based on integrated buck half-bridge resonant inverter , 2000, APEC 2000. Fifteenth Annual IEEE Applied Power Electronics Conference and Exposition (Cat. No.00CH37058).

[10]  Shmuel Ben-Yaakov,et al.  Current-sourcing push-pull parallel-resonance inverter (CS-PPRI): theory and application as a discharge lamp driver , 1994, IEEE Trans. Ind. Electron..

[11]  토마스 제이. 리바리치,et al.  High intensity discharge lamp ballast circuit , 2004 .

[12]  Toshihisa Shimizu,et al.  Characteristics of ballast for HID lamp with single-ended resonant-type inverter circuit using leakage inductance of transformer , 1995, Proceedings of 1995 International Conference on Power Electronics and Drive Systems. PEDS 95.

[13]  J. A. Sabate,et al.  A high efficiency DC/DC converter as the front-end stage of high intensity discharge lamp ballasts for automobiles , 2000, Proceedings IPEMC 2000. Third International Power Electronics and Motion Control Conference (IEEE Cat. No.00EX435).

[14]  Sam Ben-Yaakov,et al.  The simplest electronic ballast for HID lamps , 1996, Proceedings of Applied Power Electronics Conference. APEC '96.

[15]  J. M. Davenport,et al.  Direct Current Operation of Low Wattage Metal Halide Lamps , 1984 .

[16]  Ka Wai Eric Cheng,et al.  Examination of the power conditioning driving circuit for automotive HID lamp , 2006 .

[17]  M. Fukuhara,et al.  A New Electronic Ballast for HID Lamps , 1988 .

[18]  J. Ribas,et al.  Complete low-cost two-stage electronic ballast for 70-W high-pressure sodium vapor lamp based on current-mode-controlled buck-boost inverter , 2005 .

[19]  Yu-Kang Lo,et al.  Design and Implementation of a Single-Stage High-Frequency HID Lamp Electronic Ballast , 2008, IEEE Transactions on Industrial Electronics.

[20]  B.H. Cho,et al.  Design and analysis of high-voltage transformer for HID lamp igniter , 2005, Twentieth Annual IEEE Applied Power Electronics Conference and Exposition, 2005. APEC 2005..

[21]  Bo-Hyung Cho,et al.  Design and analysis of automotive high intensity discharge lamp ballast using micro controller unit , 2003 .

[22]  K.W.E. Cheng,et al.  Voltage Multiplier Integrated HID Ballast and the Application of Triple Insulated Wire in the Design of Igniter Transformer , 2006, 2006 2nd International Conference on Power Electronics Systems and Applications.