Variation of the vertical stiffness of strip-shaped fiber-reinforced elastomeric isolators under lateral loading

Abstract A fiber-reinforced elastomeric isolator (FREI) is a relatively new type of isolator that utilizes fiber material for the reinforcing layers. FREIs can be installed in a bonded or unbonded application. In this study, finite element analysis (FEA) is carried out on bonded and unbonded strip-shaped FREIs to investigate the variation in vertical stiffness as the isolator undergoes lateral displacement. The vertical stiffness of the isolators under pure compression obtained by FEA was in good agreement with the predictions of two available closed-form solutions. As the lateral displacement increases, it was observed that for bonded FREIs the vertical stiffness decreases monotonically; whereas, for unbonded FREIs, the vertical stiffness decreased up to 175% shear deformation, where an increase in vertical stiffness was observed. FEA results confirmed that the effective overlap area method provides reasonable estimates for the vertical stiffness of bonded FREIs. It is observed that as the applied vertical stress increases, the vertical stiffness of bonded and unbonded FREIs increases. Finally, the paper shows that under large lateral displacements, bonded FREIs develop large tensile stresses in the regions outside the overlapping areas, while the tensile stresses that develop in unbonded FREIs are very low and confined in a small region.

[1]  Dimitrios Konstantinidis,et al.  Experimental and finite element study on the compression properties of Modified Rectangular Fiber-Reinforced Elastomeric Isolators (MR-FREIs) , 2014 .

[2]  Hsiang-Chuan Tsai,et al.  Compression stiffness of infinite-strip bearings of laminated elastic material interleaving with flexible reinforcements , 2004 .

[3]  Michael Tait,et al.  Experimental and finite element study on the lateral response of modified rectangular fiber-reinforced elastomeric isolators (MR-FREIs) , 2015 .

[4]  Satish Nagarajaiah,et al.  Stability of Elastomeric Isolation Bearings: Experimental Study , 2002, Journal of Structural Engineering.

[5]  Robert G. Drysdale,et al.  Bonded versus unbonded strip fiber reinforced elastomeric isolators: Finite element analysis , 2011 .

[6]  Hamid Toopchi-Nezhad,et al.  Influence of thickness of individual elastomer layers (first shape factor) on the response of unbonded fiber-reinforced elastomeric bearings , 2013 .

[7]  Fuad Okay,et al.  Compression of hollow-circular fiber-reinforced rubber bearings , 2011 .

[8]  Robert G. Drysdale,et al.  Lateral Response Evaluation of Fiber-Reinforced Neoprene Seismic Isolators Utilized in an Unbonded Application , 2008 .

[9]  J. Kelly.  Analysis of Fiber-Reinforced Elastomeric Isolators , 1999 .

[10]  James M. Kelly,et al.  A simple mechanical model for elastomeric bearings used in base isolation , 1988 .

[11]  Gaetano Russo,et al.  Sliding instability of fiber-reinforced elastomeric isolators in unbonded applications , 2013 .

[12]  Dimitrios Konstantinidis,et al.  Effect of Friction on Unbonded Elastomeric Bearings , 2009 .

[13]  Gaetano Russo,et al.  Experimental Behavior of Carbon Fiber Reinforced Isolators , 2008 .

[14]  Dimitrios Konstantinidis,et al.  Mechanics of Rubber Bearings for Seismic and Vibration Isolation , 2011 .

[15]  Dimitrios Konstantinidis,et al.  Structural and nonstructural performance of a seismically isolated building using stable unbonded fiber‐reinforced elastomeric isolators , 2016 .

[16]  Dimitrios Konstantinidis,et al.  Finite element analysis of unbonded square fiber-reinforced elastomeric isolators (FREIs) under lateral loading in different directions , 2014 .

[17]  Beom-Soo Kang,et al.  Design and manufacturing of fiber reinforced elastomeric isolator for seismic isolation , 2002 .

[18]  Alfred Strauss,et al.  Numerical modeling of elastomeric bearings in structural engineering , 2011 .

[19]  Dimitrios Konstantinidis,et al.  Three-dimensional finite element analysis of circular fiber-reinforced elastomeric bearings under compression , 2014 .

[20]  Gordon P. Warn,et al.  Mechanistic Model for Simulating Critical Behavior in Elastomeric Bearings , 2015 .

[21]  James M. Kelly,et al.  Pacific Earthquake Engineering Research Center Analytical and Experimental Study of Fiber-Reinforced Elastomeric Isolators , 2003 .

[22]  Robert G. Drysdale,et al.  Testing and modeling of square carbon fiber‐reinforced elastomeric seismic isolators , 2008 .

[23]  James M. Kelly,et al.  Bending Stiffness of Fiber-Reinforced Circular Seismic Isolators , 2002 .

[24]  James M. Kelly,et al.  Stability and post-buckling behavior in nonbolted elastomeric isolators , 2010 .

[25]  Yalcin Mengi,et al.  Elastic layers bonded to flexible reinforcements , 2008 .

[26]  Andrew S. Whittaker,et al.  Vertical Stiffness of Elastomeric and Lead–Rubber Seismic Isolation Bearings , 2007 .

[27]  Hamid Toopchi-Nezhad,et al.  Stability of fiber-reinforced elastomeric bearings in an unbonded application , 2011 .

[28]  M. Shahria Alam,et al.  Sensitivity analysis of carbon fiber-reinforced elastomeric isolators based on experimental tests and finite element simulations , 2014, Bulletin of Earthquake Engineering.

[29]  Dimitrios Konstantinidis,et al.  Compression of unbonded rubber layers taking into account bulk compressibility and contact slip at the supports , 2016 .

[30]  Dimitrios Konstantinidis,et al.  Partially bonded fiber‐reinforced elastomeric isolators (PB‐FREIs) , 2015 .

[31]  Alfred Strauss,et al.  An innovative earthquake isolation system using fibre reinforced rubber bearings , 2008 .

[32]  James M. Kelly,et al.  Seismic Isolation Systems for Developing Countries , 2002 .

[33]  Ugurhan Akyuz,et al.  A new formulation for the analysis of elastic layers bonded to rigid surfaces , 2006 .

[34]  R. D. Wood,et al.  Nonlinear Continuum Mechanics for Finite Element Analysis , 1997 .

[35]  Michael Tait,et al.  A numerical study on the compressive and rotational behavior of fiber reinforced elastomeric isolators (FREI) , 2015 .