Preload Monitoring of Bolted L-Shaped Lap Joints Using Virtual Time Reversal Method

L-shaped bolt lap joints are commonly used in aerospace and civil structures. However, bolt joints are frequently subjected to loosening, and this has a significant effect on the safety and reliability of these structures. Therefore, bolt preload monitoring is very important, especially at the early stage of loosening. In this paper, a virtual time reversal guided wave method is presented to monitor preload of bolted L-shaped lap joints accurately and simply. In this method, a referenced reemitting signal (RRS) is extracted from the bolted structure in fully tightened condition. Then the RRS is utilized as the excitation signal for the bolted structure in loosening states, and the normalized peak amplitude of refocused wave packet is used as the tightness index (TIA). The proposed method is experimentally validated by L-shaped bolt joints with single and multiple bolts. Moreover, the selections of guided wave frequency and tightness index are also discussed. The results demonstrate that the relationship between TIA and bolt preload is linear. The detection sensitivity is improved significantly compared with time reversal (TR) method, particularly when bolt loosening is at its embryo stage. The results also show that TR method is an effective method for detection of the number of loosening bolts.

[1]  Arup K. Maji,et al.  An Assessment of Joint Rigidity with Ultrasonic Wave Energy , 2011 .

[2]  Hoon Sohn,et al.  Integrated impedance and guided wave based damage detection , 2012 .

[3]  P. M. Mujumdar,et al.  Time reversibility of a Lamb wave for damage detection in a metallic plate , 2011 .

[4]  Fu-Kuo Chang,et al.  Detection of bolt loosening in C–C composite thermal protection panels: I. Diagnostic principle , 2006 .

[5]  Fu-Kuo Chang,et al.  Detection of bolt loosening in C–C composite thermal protection panels: II. Experimental verification , 2006 .

[6]  Wang Tao,et al.  Health monitoring of bolted joints using the time reversal method and piezoelectric transducers , 2016 .

[7]  Brandon Arritt,et al.  Bolted Joint Integrity Structural Health Monitoring for Responsive Space Satellites , 2009 .

[8]  Liping Huang,et al.  Spatial resolution improvement for Lamb wave-based damage detection using frequency dependency compensation , 2017 .

[9]  Jun Hong,et al.  Application of ultrasound technique to evaluate contact condition on the faying surface of riveted joints , 2015 .

[10]  Hoon Sohn,et al.  Time reversal active sensing for health monitoring of a composite plate , 2007 .

[11]  Ratneshwar Jha,et al.  A modified time reversal method for Lamb wave based diagnostics of composite structures , 2012 .

[12]  Michele Meo,et al.  Structural health monitoring of bolted joints using linear and nonlinear acoustic/ultrasound methods , 2011 .

[13]  Gangbing Song,et al.  Real time bolt preload monitoring using piezoceramic transducers and time reversal technique—a numerical study with experimental verification , 2016, Smart Materials and Structures.

[14]  Gangbing Song,et al.  Proof-of-concept study of monitoring bolt connection status using a piezoelectric based active sensing method , 2013 .

[15]  Bin Lin,et al.  Space Application of Piezoelectric Wafer Active Sensors for Structural Health Monitoring , 2011 .

[16]  Baotong Li,et al.  Comparison of the Influences of Surface Texture and Boundary Slip on Tribological Performances , 2015 .

[17]  Ricardo Perera,et al.  Active Wireless System for Structural Health Monitoring Applications , 2017, Sensors.

[18]  Xiangjun Jiang,et al.  On controlling preload and estimating anti-loosening performance in threaded fasteners based on accurate contact modeling , 2016 .

[19]  Victor Giurgiutiu,et al.  Single Mode Tuning Effects on Lamb Wave Time Reversal with Piezoelectric Wafer Active Sensors for Structural Health Monitoring , 2007 .

[20]  Aly El-Osery,et al.  Health monitoring of 90° bolted joints using fuzzy pattern recognition of ultrasonic signals , 2013 .

[21]  Brandon Arritt,et al.  Damage Detection in Bolted Space Structures , 2010 .

[22]  F. Cegla,et al.  Compensation of phase response changes in ultrasonic transducers caused by temperature variations , 2019 .

[23]  Tat-Hean Gan,et al.  Structural Health Monitoring of Above-Ground Storage Tank Floors by Ultrasonic Guided Wave Excitation on the Tank Wall , 2017, Sensors.

[24]  Junkang Guo,et al.  Integration of geometric variation and part deformation into variation propagation of 3-D assemblies , 2016 .

[25]  S. Yuan,et al.  High spatial resolution imaging for structural health monitoring based on virtual time reversal , 2011 .

[26]  H. Sohn,et al.  Understanding a time reversal process in Lamb wave propagation , 2009 .

[27]  Tribikram Kundu,et al.  Health Monitoring of Structural and Biological Systems 2011 , 2011 .

[28]  Weidong Zhu,et al.  Finite Element Modeling of Structures With L-Shaped Beams and Bolted Joints , 2011 .

[29]  Weidong Zhu,et al.  Detecting Loosening of Bolted Connections in a Pipeline Using Changes in Natural Frequencies , 2014 .

[30]  Tadeusz Stepinski,et al.  Multi-stage temperature compensation method for Lamb wave measurements , 2016 .

[31]  Brandon Arritt,et al.  Embedded nonlinear ultrasonics for structural health monitoring of satellite joints , 2008, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[32]  Jing Lin,et al.  A Modified Lamb Wave Time-Reversal Method for Health Monitoring of Composite Structures , 2017, Sensors.

[33]  Brandon Arritt,et al.  Piezoelectric Wafer Active Sensor Structural Health Monitoring of Space Structures , 2010 .

[34]  Rui Sun,et al.  Damage Detection Based on Power Dissipation Measured with PZT Sensors through the Combination of Electro-Mechanical Impedances and Guided Waves , 2016, Sensors.

[35]  Jing Lin,et al.  Amplitude Dispersion Compensation for Damage Detection Using Ultrasonic Guided Waves , 2016, Sensors.

[36]  Arup K. Maji,et al.  Ultrasonic Evaluation of Bolted Connections in Satellites , 2014 .

[37]  Dan Li,et al.  Lamb Wave-Based Structural Health Monitoring on Composite Bolted Joints under Tensile Load , 2017, Materials.

[38]  M. Fink,et al.  Time-reversed Lamb waves , 1998, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[39]  Magdalena Rucka,et al.  Research on assessment of bolted joint state using elastic wave propagation , 2015 .