In-plane elastic response of two-segment circular-axis symmetric notch flexure hinges: The right circular design

Abstract This work presents a general analytical model of the planar compliances for two-segment circular-axis symmetric notch flexure hinges. Compared to a similar straight-axis flexure design, the circular-axis configuration enhances the design parameter domain by adding the median circle radius. Six compliances are formulated with respect to a central reference frame and to an end reference frame in terms of a smaller number of half-flexure compliances. The model covers both relatively large radius-to-thickness ratio designs (thin flexures) and small radius-to-thickness ratio configurations (thick flexures). The new circular-axis right circular flexure is introduced to illustrate the general model. Predictions of the analytical compliance model for this flexure were confirmed by finite element analysis and experimental testing. The analytical model is further utilized to investigate the influence of normal and shear forces in the thick-member model and to assess the accuracy of the simpler thin-beam model, which considers only bending. A comparison is also performed between the corresponding compliances of the new circular-axis flexure design and the existing straight-axis right circular flexure hinge in terms of defining geometric parameters.

[1]  Jonathan B. Hopkins,et al.  Synthesis of multi-degree of freedom, parallel flexure system concepts via freedom and constraint topology (FACT). Part II: Practice , 2010 .

[2]  G. Cowper.  The Shear Coefficient in Timoshenko’s Beam Theory , 1966 .

[3]  Q. Yang,et al.  A Monolithic Compliant Piezoelectric-Driven Microgripper: Design, Modeling, and Testing , 2013, IEEE/ASME Transactions on Mechatronics.

[4]  John C. Ziegert,et al.  Hybrid bi-directional flexure joint , 2014 .

[5]  Nicolae Lobontiu,et al.  Compliant Mechanisms: Design of Flexure Hinges , 2002 .

[6]  Nicolae Lobontiu,et al.  Symmetry-Based Compliance Model of Multisegment Notch Flexure Hinges , 2012 .

[7]  Jingyan Dong,et al.  Development of a High-Bandwidth XY Nanopositioning Stage for High-Rate Micro-/Nanomanufacturing , 2011, IEEE/ASME Transactions on Mechatronics.

[8]  Xiaoyuan Liu,et al.  Elliptical-Arc-Fillet Flexure Hinges: Toward a Generalized Model for Commonly Used Flexure Hinges , 2011 .

[9]  Stuart T. Smith,et al.  Flexures: Elements of Elastic Mechanisms , 2000 .

[10]  Nicolae Lobontiu.  Note: Bending compliances of generalized symmetric notch flexure hinges. , 2012, The Review of scientific instruments.

[11]  Bi Shusheng,et al.  Dimensionless design graphs for three types of annulus-shaped flexure hinges , 2010 .

[12]  ZhiWu Li,et al.  Right-circular corner-filleted flexure hinges , 2005, IEEE International Conference on Automation Science and Engineering, 2005..

[13]  Saša Zelenika,et al.  Optimized flexural hinge shapes for microsystems and high-precision applications , 2009 .

[14]  Qingsong Xu,et al.  Design and Development of a Flexure-Based Dual-Stage Nanopositioning System With Minimum Interference Behavior , 2012, IEEE Transactions on Automation Science and Engineering.

[15]  Zhijiang Du,et al.  Stiffness research on a high-precision, large-workspace parallel mechanism with compliant joints , 2008 .

[16]  Eric R. Marsh,et al.  A unified geometric model for designing elastic pivots , 2008 .

[17]  Yanling Tian,et al.  A flexure-based mechanism and control methodology for ultra-precision turning operation , 2009 .

[18]  Bijan Shirinzadeh,et al.  Development of a high precision flexure-based microgripper , 2009 .

[19]  N. Lobontiu,et al.  A generalized analytical compliance model for transversely symmetric three-segment flexure hinges. , 2011, The Review of scientific instruments.

[20]  Dong Sun,et al.  Manipulating rigid payloads with multiple robots using compliant grippers , 2002 .

[21]  F. Hsiao,et al.  Analysis of a novel flexure hinge with three degrees of freedom , 2001 .

[22]  David Zhang,et al.  Closed-form compliance equations of filleted V-shaped flexure hinges for compliant mechanism design , 2010 .

[23]  Stuart T. Smith,et al.  ELLIPTICAL FLEXURE HINGES , 1997 .

[24]  Nicolae Lobontiu,et al.  Corner-Filleted Flexure Hinges , 2001 .

[25]  S. Bashash,et al.  Robust Adaptive Control of Coupled Parallel Piezo-Flexural Nanopositioning Stages , 2009, IEEE/ASME Transactions on Mechatronics.

[26]  J. Paros.  How to design flexure hinges , 1965 .