Effects of reinforcement particle size in MMCs on extrusion die wear

Abstract In this study, extrusion die wear during the metal matrix composite (MMC) extrusion process was investigated with regard to the size of the reinforcement particle. Extrusion die materials were AISI H13 hot working die steel and were machined by EDM in order to gain rectangular and circular die bearings. The dies were hardened, tempered and grounded to be prepared for extrusion processes. AA 6063 aluminium matrix composite billets reinforced with SiC particles (Al/SiCp) were prepared by stir casting method for extrusion process. Different SiC particulate sizes (53 μm, 167 μm and 478 μm) and constant volume fraction (10%) were used for the reinforcement of the matrix. Extrusion processes of the prepared composite billets were conducted at 500 °C with ram speed of 2 mm/s and extrusion ratio of 25:1 under laboratory condition. The variation of die wears with SiC particle size was characterised by weight loss in the die as a result of extrudate length and roughness of the die bearing surface. SEM and OM studies were also carried out for the observation of wear mechanism of the die bearing surfaces. The results of this study show that the die wear is affected differently by the SiC particle size. The SiC size of 167 μm is a critical size for die wear during the Al matrix composite extrusion process, since the die wear and surface roughness increase up to the size of 167 μm and then they decrease although the SiC particle size in the billets increase up to 478 μm. The wear mechanisms of the die bearing surface are predominantly abrasion with microcutting, wedge-forming and ploughing modes.

[1]  Jian-Xin Xie,et al.  Processing and microstructure of functionally graded W/Cu composites fabricated by multi-billet extrusion using mechanically alloyed powders , 2006 .

[2]  W. Yanwen,et al.  Plastic working and superplasticity in aluminium–matrix composites reinforced with SiC particulates , 1998 .

[3]  J. Yeh,et al.  An in situ composite of Al (graphite, Al4C3) produced by reciprocating extrusion , 2000 .

[4]  C. Kang,et al.  Effects of hot extrusion through a curved die on the mechanical properties of SiCp/Al composites fabricated by melt-stirring , 1999 .

[5]  C. Kang,et al.  The effect of die shape on the hot extrudability and mechanical properties of 6061 Al/Al2O3 composites , 2000 .

[6]  K. Morsi,et al.  Effect of particle size and volume fraction on hot extrusion reaction synthesis of SiC particle reinforced NiAl , 2000 .

[7]  M. Surappa,et al.  Particle redistribution and matrix microstructure evolution during hot extrusion of cast SiCp reinforced aluminium alloy matrix composites , 1998 .

[8]  O. P. Grover,et al.  Extrusion characteristics of aluminium alloy/SiCpmetal matrix composites , 1999 .

[9]  H. Mcqueen,et al.  Extrusion modelling of 6061 aluminium alloy and particle reinforced MMCs , 1998 .

[10]  Jien-Wei Yeh,et al.  Study of 6061-Al2O3p composites produced by reciprocating extrusion , 2000 .

[11]  Manoj Gupta,et al.  Effect of limited matrix–reinforcement interfacial reaction on enhancing the mechanical properties of aluminium–silicon carbide composites , 2001 .

[12]  Farghalli A. Mohamed,et al.  Particulate reinforced metal matrix composites — a review , 1991, Journal of Materials Science.

[13]  J. Torralba,et al.  P/M aluminum matrix composites: an overview , 2003 .

[14]  H. Mcqueen,et al.  Modelling extrusion of 2618 aluminium alloy and 2618-1 10%AI203 and 2618-20%AI203 composites , 1998 .

[15]  E. Candan,et al.  Abrasive wear behaviour of Al–SiC composites produced by pressure infiltration technique , 2001 .

[16]  J. Duszczyk.  Prevention of Stick-slip Tearing of a Duralcan AA6061–matrix Composite During Extrusion , 1998 .

[17]  Jae-Chul Lee,et al.  Processing and interfacial bonding strength of 2014 Al matrix composites reinforced with oxidized SiC particles , 2006 .

[18]  B. Dodd,et al.  Room temperature formability of particle-reinforced metal matrix composites: forging, extrusion and deep drawing , 1995 .

[19]  Fionn P.E. Dunne,et al.  Modelling central bursting in the extrusion of particulate reinforced metal matrix composite materials , 1997 .

[20]  Jae-Chul Lee,et al.  Mechanical properties of 2014Al/SiC composites with oxidized SiC particles , 2003 .

[21]  M.S.J. Hashmi,et al.  Metal matrix composites: production by the stir casting method , 1999 .

[22]  B. Bacroix,et al.  Influence of microstructures and particle concentrations on the development of extrusion textures in metal matrix composites , 1995 .

[23]  M. Lieblich,et al.  Extrudability of PM 2124/SiCp aluminium matrix composite , 1997 .

[24]  Y. Murakoshi,et al.  Microstructures and mechanical properties of Al-Li/SiCp composite produced by extrusion processing , 1997 .

[25]  E. Candan,et al.  Abrasive wear behavior and mechanical properties of Al-Si/SiC composites , 2004 .

[26]  I. V. Samarasekera,et al.  Mathematical modeling of the extrusion of 6061/Al2O3/20p composite , 1996 .