On the relation between the mode I fracture toughness of a composite laminate and that of a 0° ply: Analytical model and experimental validation

Abstract This paper proposes a simple model to predict the fracture toughness of multidirectional carbon–epoxy composite laminates using the fracture toughness of the 0° ply. The model is based on a combination of Linear-Elastic Fracture Mechanics and lamination theory, and uses as material properties the ply elastic properties and the fracture toughness of the 0° ply measured in compact tension test specimens. A good correlation is obtained by comparing the model predictions and experimental data obtained in center-cracked specimens manufactured using different lay-ups and materials.

[1]  Norman A. Fleck,et al.  Compressive failure of notched carbon fibre composites , 1993, Proceedings of the Royal Society of London. Series A: Mathematical and Physical Sciences.

[2]  Seng-Chuan Tan,et al.  Stress Concentrations in Laminated Composites , 1994 .

[3]  Anthony M. Waas,et al.  Prediction of progressive failure in multidirectional composite laminated panels , 2007 .

[4]  K. Kageyama.  Fracture Mechanics of Notched Carbon/Epoxy Laminates , 1989 .

[5]  Theo de Jong,et al.  Stresses Around Pin-Loaded Holes in Elastically Orthotropic or Isotropic Plates , 1977 .

[6]  P. Camanho,et al.  A design methodology for mechanically fastened joints in laminated composite materials , 2006 .

[7]  Norman A. Fleck,et al.  Failure Prediction Technique for Compression Loaded Carbon Fibre-Epoxy Laminate with Open Holes , 1991 .

[8]  C. Sun,et al.  Fracture Criterion for Notched Thin Composite Laminates , 1997 .

[9]  P. Camanho,et al.  Measurement of resistance curves in the longitudinal failure of composites using digital image correlation , 2010 .

[10]  Pedro P. Camanho,et al.  A continuum damage model for composite laminates: Part I - Constitutive model , 2007 .

[11]  Lorenzo Iannucci,et al.  Fracture toughness of the tensile and compressive fibre failure modes in laminated composites , 2006 .

[12]  J. Whitney,et al.  Stress Fracture Criteria for Laminated Composites Containing Stress Concentrations , 1974 .

[13]  D. W. Wilson,et al.  Analysis of the Net Tension Failure Mode in Composite Bolted Joints , 1982 .

[14]  Jan Backlund,et al.  Tensile Fracture of Laminates with Holes , 1986 .

[15]  Zhigang Suo,et al.  The role of material orthotropy in fracture specimens for composites , 1992 .

[16]  L. Carlsson,et al.  Notch sensitivity of thermoset and thermoplastic laminates loaded in tension , 1989 .

[17]  Ireneusz Lapczyk,et al.  Progressive damage modeling in fiber-reinforced materials , 2007 .

[18]  N. Fleck,et al.  Effect of geometry on compressive failure of notched composites , 1993 .

[19]  Jan Bäcklund,et al.  FRACTURE ANALYSIS OF NOTCHED COMPOSITES , 1981 .

[20]  Klaus Friedrich,et al.  Application of fracture mechanics to composite materials , 1989 .

[21]  D. Mollenhauer,et al.  Three-dimensional stress analysis and Weibull statistics based strength prediction in open hole composites , 2007 .

[22]  L. Sluys,et al.  Continuum Models for the Analysis of Progressive Failure in Composite Laminates , 2009 .

[23]  Jan Backlund,et al.  Tensile Fracture of Laminates with Cracks , 1986 .

[24]  Pedro P. Camanho,et al.  A continuum damage model for composite laminates: Part II – Computational implementation and validation , 2007 .