Effects of alumina in nonmetallic brake friction materials on friction performance

The effects of alumina (Al2O3) as an abrasive on brake friction performance and friction layers of nonmetallic brake friction materials were evaluated. Five experimental compositions containing from 0 to 14.6 vol% alumina were tested (Al2O3—0, 3.4, 5.6, 9.0, and 14.6 vol%). The experimental results indicated that alumina enhances friction coefficient and improves wear performance. The formation and development of friction layers were characterized using X-ray fluorescence spectrometry and scanning electron microscopy with energy dispersive X-ray analysis. Phenomena of baryte film and transferred iron-containing film formed on the friction surfaces were observed. Baryte films were detected on specimens containing from 0 to 5.6 vol% alumina. Iron-containing films were detected on surfaces of all alumina-containing specimens but not on the material without alumina. The role of abrasive in nonmetallic friction materials was studied in relation to formulation, friction performance, and friction surfaces.

[1]  A. Wirth,et al.  An energy dispersive x-ray and imaging x-ray photoelectron spectroscopical study of transfer film chemistry and its influence on fricttion coefficient , 1992 .

[2]  Staffan Jacobson,et al.  Surface characterisation of brake pads after running under silent and squealing conditions , 1999 .

[3]  Ho Jang,et al.  The effects of antimony trisulfide (Sb2S3) and zirconium silicate (ZrSiO4) in the automotive brake friction material on friction characteristics , 2000 .

[4]  G. Ostermeyer,et al.  Friction and wear of brake systems , 2001 .

[5]  M. Griepentrog,et al.  Chemical and microstructural changes induced by friction and wear of brakes , 2001 .

[6]  Yafei Lu,et al.  Optimization of a commercial brake pad formulation , 2002 .

[7]  Staffan Jacobson,et al.  On the nature of tribological contact in automotive brakes , 2002 .

[8]  David Rafaja,et al.  On friction layer formation in polymer matrix composite materials for brake applications , 2002 .

[9]  Yafei Lu.  A combinatorial approach for automotive friction materials: Combined effects of ingredients on friction performance , 2002 .

[10]  M. A. Wright,et al.  Modeling Wear Traces of Automotive Friction Materials by Cantor Set , 2002 .

[11]  Yafei Lu.  A Golden Section approach to optimization of automotive friction materials , 2003 .

[12]  M. A. Wright,et al.  Optimization of a Semimetallic Friction Material Formulation , 2004 .

[13]  Werner Österle,et al.  Friction layers and friction films on PMC brake pads , 2004 .

[14]  Yafei Lu,et al.  Combinatorial Screening of Ingredients for Steel Wool Based Semimetallic and Aramid Pulp Based Nonasbestos Organic Brake Materials , 2004 .

[15]  D. Landolt,et al.  Third body effects and material fluxes in tribocorrosion systems involving a sliding contact , 2004 .

[16]  Lu Yafei.  Combinatorial Friction Materials Research , 2004 .

[17]  Gwidon Stachowiak,et al.  Review of automotive brake friction materials , 2004 .

[18]  Ho Jang,et al.  The Role of Transfer Layers on Friction Characteristics in the Sliding Interface between Friction Materials against Gray Iron Brake Disks , 2005 .

[19]  Ling Han,et al.  Optimization of ceramic friction materials , 2006 .

[20]  Yafei Lu,et al.  A combinatorial approach for automotive friction materials: Effects of ingredients on friction performance , 2006 .

[21]  M. Müller,et al.  Dynamic interaction of friction and surface topography in brake systems , 2006 .

[22]  M. A. Wright,et al.  Sensitivity series and friction surface analysis of non-metallic friction materials , 2006 .

[23]  Werner Österle,et al.  Towards a better understanding of brake friction materials , 2007 .

[24]  Georg-Peter Ostermeyer,et al.  Cellular automata method for macroscopic surface and friction dynamics in brake systems , 2007 .