Numerical study of vortex eccentricity in a gas cyclone

Abstract This paper presents a numerical study of the vortex eccentricity in a gas cyclone and its effect on the performance of the cyclone. The gas flow in the cyclone was modeled as an unsteady flow by the Navier–Stokes equations with the Reynolds Stress Model (RSM) as the turbulence model. The particles were modelled by the Lagrangian particle tracking (LPT) approach in an unsteady gas flow. Gas cyclones with the same dimensions and total flow rates but different numbers of inlets were simulated with the inlet velocity varying from 12 to 20 m/s. The vortex eccentricities in different cases were analyzed in terms of radial deviation and angular deviation. In addition, the frequency of the precessing vortex core (PVC) was analyzed by the fast Fourier transform (FFT). The results show that the vortex center in the single inlet cyclone has a great eccentricity and its precession center is also different from the geometric center, which reduces the particle collection efficiency. The increase in the symmetry of the inlet causes only a very small increase in the pressure drop in the simulated cases, but it can significantly reduce the vortex eccentricity, particularly by eliminating the eccentricity of the PVC center. The improvement of the vortex eccentricity can generally increase the collection efficiency for particles greater than 2.0 µm. The increase of the collection efficiency is mainly because the symmetrical vortex can restrain the short-circuiting flow of particles. The results can improve the understanding of the vortex flow in gas cyclones which may guide the optimization of gas cyclones.

[1]  Hu Zhang,et al.  Numerical simulation of the asymmtric gas phase flow field in a volute cyclone seperator , 2005 .

[2]  Renata Gnatowska,et al.  Polyhedral meshing as an innovative approach to computational domain discretization of a cyclone in a fluidized bed CLC unit , 2017 .

[3]  J. Derksen,et al.  Simulating turbulent swirling flow in a gas cyclone: A comparison of various modeling approaches , 2011 .

[4]  K. Dong,et al.  A New Fine Particle Removal Technology: Cloud-Air-Purifying , 2018, Industrial & Engineering Chemistry Research.

[5]  Binbin Pei,et al.  Function and effect of the inner vortex on the performance of cyclone separators , 2017 .

[6]  A. Yu,et al.  Discrete particle simulation of particle–fluid flow: model formulations and their applicability , 2010, Journal of Fluid Mechanics.

[7]  A. Yu,et al.  Numerical study of gas–solid flow in a cyclone separator , 2006 .

[8]  Binbin Pei,et al.  Numerical analysis of forces exerted on particles in cyclone separators , 2016 .

[9]  U. Ghia,et al.  Procedure for Estimation and Reporting of Uncertainty Due to Discretization in CFD Applications , 2007 .

[10]  Edgar Muschelknautz,et al.  Aerodynamische Beiwerte des Zyklonabscheiders aufgrund neuer und verbesserter Messungen , 1970 .

[11]  Pradyumna Ghosh,et al.  The effect of modeling of velocity fluctuations on prediction of collection efficiency of cyclone separators , 2013 .

[12]  J. Wang,et al.  Analysis of the effect of vortex on the flow field of a cylindrical cyclone separator , 2019, Separation and Purification Technology.

[13]  A. Hoekstra,et al.  Gas flow field and collection efficiency of cyclone separators , 2000 .

[14]  Shi Ming-xian.  Numerical simulation of precessing vortex core in cyclone separator , 2007 .

[15]  R. Chanaud.  Observations of oscillatory motion in certain swirling flows , 1965, Journal of Fluid Mechanics.

[16]  J. Zhang,et al.  Simulation of Gas Flow Pattern and Separation Efficiency in Cyclone with Conventional Single and Spiral Double Inlet Configuration , 2006 .

[17]  Qinfu Hou,et al.  Modelling of Inclusion Motion and Flow Patterns in Swirling Flow Tundishes with Symmetrical and Asymmetrical Structures , 2008 .

[18]  K. Elsayed,et al.  The effect of cyclone inlet dimensions on the flow pattern and performance , 2011 .

[19]  S. Pirker,et al.  CFD Simulations of Pressure Drop and Velocity Field in a Cyclone Separator with Central Vortex Stabilization Rod , 2016 .

[20]  M. Juniper,et al.  Local linear stability analysis of cyclone separators , 2017, Journal of Fluid Mechanics.

[21]  O. Hamdy,et al.  Numerical study of the effect of changing the cyclone cone length on the gas flow field , 2017 .

[22]  K. Elsayed,et al.  The effect of cyclone vortex finder dimensions on the flow pattern and performance using LES , 2013 .

[23]  Characterization of the PVC phenomena in the exhaust of a cyclone dust separator , 1994 .

[24]  Bow-yaw Wang,et al.  CFD–DEM simulation of the gas–solid flow in a cyclone separator , 2011 .

[25]  W. P. Martignoni,et al.  Evaluation of cyclone geometry and its influence on performance parameters by computational fluid dynamics (CFD) , 2007 .

[26]  Soon-Bark Kwon,et al.  Characteristics of the collection efficiency for a double inlet cyclone with clean air , 2003 .

[27]  Alex C. Hoffmann,et al.  Gas Cyclones and Swirl Tubes , 2002 .

[28]  Theodore C. Carney,et al.  A 10-.mu.m cutpoint inlet for the dichotomous sampler. , 1982, Environmental science & technology.

[29]  Hualin Wang,et al.  Inlet Particle-Sorting Cyclone for the Enhancement of PM2.5 Separation. , 2017, Environmental science & technology.

[30]  Ic Shepherd,et al.  Validation of a CFD model for predicting gas flow in a cyclone , 1999 .

[31]  K. Elsayed,et al.  Numerical modeling of the flow field and performance in cyclones of different cone-tip diameters , 2011 .

[32]  Henggen Shen,et al.  Development of a symmetrical spiral inlet to improve cyclone separator performance , 2004 .

[33]  Jianjun Wang,et al.  Performance evaluation of a new cyclone separator – Part II simulation results☆ , 2016 .

[34]  K. J. Walker,et al.  A Parametric Evaluation of the Hydrocyclone Separation of Drilling Mud from Drilled Rock Chippings , 1992 .

[35]  H. Shalaby,et al.  Comparative study of the continuous phase flow in a cyclone separator using different turbulence models , 2005 .

[36]  Binbin Pei,et al.  The effect of cross-shaped vortex finder on the performance of cyclone separator , 2017 .

[37]  Jos Derksen,et al.  Simulation of vortex core precession in a reverse‐flow cyclone , 2000 .

[38]  M. Gautam,et al.  Performance of a respirable multi-inlet cyclone sampler , 1997 .

[39]  J. Derksen,et al.  An experimental and numerical study of turbulent swirling flow in gas cyclones , 1999 .

[40]  R. DeOtte,et al.  A Model for the Prediction of the Collection Efficiency Characteristics of a Small, Cylindrical Aerosol Sampling Cyclone , 1990 .

[41]  N. Syred.  A review of oscillation mechanisms and the role of the precessing vortex core (PVC) in swirl combustion systems , 2006 .

[42]  Andrew Hursthouse,et al.  The rapid development of small scale cyclones — numerical modelling versus empirical models , 2016 .

[43]  A. Mcfarland,et al.  Design methodology for multiple inlet cyclones , 1996 .

[44]  T. O’Doherty,et al.  Vortex breakdown: a review , 2001 .

[45]  Cristóbal Cortés,et al.  Modeling the gas and particle flow inside cyclone separators , 2007 .

[46]  Qiji Sun,et al.  Effect of the inlet angle on the performance of a cyclone separator using CFD-DEM , 2019, Advanced Powder Technology.

[47]  R. Sripriya,et al.  CFD modelling of hydrocyclone—prediction of cut size , 2005 .

[48]  Anthony John Griffiths,et al.  Experimental Analysis of Rotating Instabilities in Swirling and Cyclonic Flows , 2008 .

[49]  Yuqing Feng,et al.  Effects of feed size distribution on separation performance of hydrocyclones with different vortex finder diameters , 2017 .

[50]  K. Elsayed,et al.  Impacts of the vortex finder eccentricity on the flow pattern and performance of a gas cyclone , 2017 .

[51]  Alex C. Hoffmann,et al.  Experimental study of the vortex end in centrifugal separators: The nature of the vortex end , 2005 .

[52]  S. A. Morsi,et al.  An investigation of particle trajectories in two-phase flow systems , 1972, Journal of Fluid Mechanics.