Effect of structural defects on corrosion initiation of TiN nanocrystalline films

[1]  A. P. Tschiptschin,et al.  TiAlN coatings deposited by triode magnetron sputtering varying the bias voltage , 2011 .

[2]  Lu Guo,et al.  Corrosion behavior of TiN-coated stainless steel as bipolar plate for proton exchange membrane fuel cell , 2010 .

[3]  S. Paul,et al.  Effect of substrate bias voltage on structural and mechanical properties of pulsed DC magnetron sputtered TiN―MoSx composite coatings , 2010 .

[4]  W. Hwang,et al.  Effect of bias voltage on the electrochemical properties of TiN coating for polymer electrolyte membrane fuel cell , 2009 .

[5]  P. Chen,et al.  Investigation of the microstructure and characterizations of TiN/CrN nanomultilayer deposited by unbalanced magnetron sputter process , 2008 .

[6]  Yibin Li,et al.  Bias effect on microstructure and mechanical properties of magnetron sputtered nanocrystalline titanium carbide thin films , 2008 .

[7]  Jia-Hong Huang,et al.  Effect of Ti interlayer on the residual stress and texture development of TiN thin films deposited by unbalanced magnetron sputtering , 2006 .

[8]  H. Barshilia,et al.  Electrochemical behavior of single layer CrN, TiN, TiAlN coatings and nanolayered TiAlN/CrN multilayer coatings prepared by reactive direct current magnetron sputtering , 2006 .

[9]  D. Lamas,et al.  Residual stresses in titanium nitride thin films deposited by direct current and pulsed direct current unbalanced magnetron sputtering , 2006 .

[10]  Liu Chenglong,et al.  Corrosion resistance and hemocompatibility of multilayered Ti/TiN-coated surgical AISI 316L stainless steel , 2005 .

[11]  Ning Jiang,et al.  XPS study for reactively sputtered titanium nitride thin films deposited under different substrate bias , 2004 .

[12]  H. Barshilia,et al.  Corrosion behavior of nanolayered TiN/NbN multilayer coatings prepared by reactive direct current magnetron sputtering process , 2004 .

[13]  J. G. Kim,et al.  Localized corrosion mechanisms of the multilayered coatings related to growth defects , 2004 .

[14]  A. Matthews,et al.  EIS comparison on corrosion performance of PVD TiN and CrN coated mild steel in 0.5 N NaCl aqueous solution , 2001 .

[15]  H. Uchida,et al.  Pinhole defect evaluation of TiN films prepared by dry coating process , 2000 .

[16]  H. Jehn.  Improvement of the corrosion resistance of PVD hard coating–substrate systems , 2000 .

[17]  I. O. Wallinder,et al.  Passivation and Anodic Oxidation of Duplex TiN Coating on Stainless Steel , 1999 .

[18]  J. Musil,et al.  A perspective of magnetron sputtering in surface engineering , 1999 .

[19]  Stergios Logothetidis,et al.  Room temperature oxidation behavior of TiN thin films , 1999 .

[20]  L. Cunha,et al.  Corrosion of TiN, (TiAl)N and CrN hard coatings produced by magnetron sputtering , 1998 .

[21]  A. E. Martinelli,et al.  An electrochemical study of magnetron-sputtered Ti- and TiN-coated steel , 1998 .

[22]  I. Alexandrou,et al.  Electron microscopy characterization of TiN films on Si, grown by d.c. reactive magnetron sputtering , 1995 .

[23]  M. N. Alias,et al.  Effect of composition and thickness on corrosion behavior of TiN and ZrN thin films , 1993 .

[24]  L. Karanović,et al.  Mechanochemical treatment of ZnO and Al2O3 powders by ball milling , 1992 .

[25]  D. M. Mattox.  Particle bombardment effects on thin‐film deposition: A review , 1989 .