New Approach to Cogging Torque Simulation Using Numerical Functions

[1]  D. Howe,et al.  Evaluation of superposition technique for calculating cogging torque in permanent-magnet brushless machines , 2006, IEEE Transactions on Magnetics.

[2]  D. Howe,et al.  Synthesis of cogging-torque waveform from analysis of a single stator slot , 2006, IEEE Transactions on Industry Applications.

[3]  Jianping Ying,et al.  A cogging torque reduction method for surface mounted permanent magnet motor , 2007, 2007 International Conference on Electrical Machines and Systems (ICEMS).

[4]  T. Lipo,et al.  Analytical Solution for Cogging Torque in Surface Permanent-Magnet Motors Using Conformal Mapping , 2008, IEEE Transactions on Magnetics.

[5]  D. Rodger,et al.  Numerical models of an induction machine , 2003 .

[6]  Chang Seop Koh,et al.  New cogging-torque reduction method for brushless permanent-magnet motors , 2003 .

[7]  Thomas A. Lipo,et al.  Modelling and experimental validation of internal short-circuit fault in salient-pole synchronous machines using numerical gap function including stator and rotor core saturation , 2013 .

[8]  Karim Abbaszadeh,et al.  Reduced Order Model of Developed Magnetic Equivalent Circuit in Electrical Machine Modeling , 2010, IEEE Transactions on Magnetics.

[9]  M. T. Nabavi-Razavi,et al.  Modeling and Simulation of a salient-pole synchronous Generator with dynamic eccentricity using modified winding function theory , 2004, IEEE Transactions on Magnetics.

[10]  Xiuhe Wang,et al.  The optimization of pole arc coefficient to reduce cogging torque in surface-mounted permanent magnet motors , 2006, IEEE Transactions on Magnetics.

[11]  T. Hamiti,et al.  Comparison Between Finite-Element Analysis and Winding Function Theory for Inductances and Torque Calculation of a Synchronous Reluctance Machine , 2007, IEEE Transactions on Magnetics.

[12]  D. Staton,et al.  Comparison of Analytical Models of Cogging Torque in Surface-Mounted PM Machines , 2012, IEEE Transactions on Industrial Electronics.

[13]  Noboru Niguchi,et al.  Cogging Torque Analysis of Magnetic Gear , 2012, IEEE Transactions on Industrial Electronics.

[14]  P. Pillay,et al.  Cogging Torque Reduction in Permanent Magnet Machines , 2006, IEEE Transactions on Industry Applications.

[15]  Gorazd Štumberger,et al.  Torque ripple reduction in exterior-rotor permanent magnet synchronous motor , 2006 .

[16]  Thomas M. Jahns,et al.  Pulsating torque minimization techniques for permanent magnet AC motor drives-a review , 1996, IEEE Trans. Ind. Electron..

[17]  Bin Yao,et al.  This article has been accepted for publication in a future issue of this journal, but has not been fully edited. Content may change prior to final publication. Coordinated Adaptive Robust Contouring Control of an Industrial Biaxial Precision Gantry with C , 2022 .

[18]  J.F. Gieras,et al.  Analytical approach to cogging torque calculation of PM brushless motors , 2004, IEEE Transactions on Industry Applications.

[19]  Ali Keyhani,et al.  Analytical model for permanent magnet motors with surface mounted magnets , 2003 .

[20]  Y. Zhilichev.  Analysis of Permanent Magnet Demagnetization Accounting for Minor $B\hbox{–}H$ Curves , 2008, IEEE Transactions on Magnetics.

[21]  Caroline A. Ross,et al.  Major hysteresis loop modeling of two-dimensional arrays of single domain particles , 2000 .

[22]  Karim Abbaszadeh,et al.  Cogging Torque Reduction in Brushless DC Motors Using Slot-Opening Shift , 2009 .

[23]  Z.Q. Zhu,et al.  Comparison of alternate analytical models for predicting cogging torque in surface-mounted permanent magnet machines , 2008, 2008 IEEE Vehicle Power and Propulsion Conference.