Molecular dynamics simulation of the nanometric cutting of silicon

Abstract Molecular dynamics simulations of nanometric cutting of single-crystal, defect-free, pure silicon were performed using the Tersoff potential over a wide range of rake angles (from -60° to +60°), widths of cut (1.1 to 4.34 ran), depths of cut (0.01 to 2.72 nm) and clearance angles (10° to 30°) to hwestigate the nature of material removal and surface generation process in ultraprecision machining and grinding. The observed material removal mechanisms can be divided into four components: (i) compression of the work material ahead of the tool; (ii) chip formation akin to an extrusion-like process; (iii) side flow; and (iv) subsurface deformation in the machined surface. Unlike in conventional machining of most ductile materials, where no volume or phase change is observed in the plastic deformation process, significant volume changes (from 18.38 to 14.19Å3), resulting in a densification of about 23% occur owing to phase transition from a diamond cubic (or α-silicon) to a bet (or β-tin structure) in the case of machining silicon. Such a structural change is typical of silicon undergoing a pressure-induced phase transformation. The extent of structural changes and their contributions to each of the four material removal mechanisms depend on the tool rake angle and the width of cut. The ratio of the width of cut to depth of cut w/d is the primary factor affecting the extent of side flow and subsurface compression. The tool rake angle and the w/d ratio are found to be dominant factors affecting the chip flow and shear zone compression ahead of the tool. Subsurface or near-surface deformation was observed with all rake angles and all cut depths down to 0.01 nm, indicating the need for an alternate final polishing process such as chemomechanical polishing to produce defect-free surfaces of silicon on an atomie scale.

[1]  Shoichi Shimada,et al.  Brittle/Ductile Transition Phenomena Observed in Computer Simulations of Machining Defect-Free Monocrystalline Silicon , 1997 .

[2]  Ranga Komanduri,et al.  Molecular dynamics simulation of atomic-scale friction , 2000 .

[3]  Nakasuji Tomoaki,et al.  Diamond Turning of Brittle Materials for Optical Components , 1990 .

[4]  Roderick R. Kunz,et al.  High resolution studies of crystalline damage induced by lapping and single-point diamond machining of Si(100) , 1996 .

[5]  J. Tersoff,et al.  New empirical approach for the structure and energy of covalent systems. , 1988, Physical review. B, Condensed matter.

[6]  N. Ikawa,et al.  Brittle-Ductile Transition Phenomena in Microindentation and Micromachining , 1995 .

[7]  I. Inasaki,et al.  Investigation of Surface Integrity by Molecular Dynamics Simulation , 1995 .

[8]  R. Cahn.  Metallic solid silicon , 1992, Nature.

[9]  Hiroaki Tanaka,et al.  On the Mechanics and Physics in the Nano-Indentation of Silicon Monocrystals. , 1999 .

[10]  J. Tersoff,et al.  Modeling solid-state chemistry: Interatomic potentials for multicomponent systems. , 1989, Physical review. B, Condensed matter.

[11]  F. Hauser,et al.  Deformation and Fracture Mechanics of Engineering Materials , 1976 .

[12]  Ranga Komanduri,et al.  MD simulation of indentation and scratching of single crystal aluminum , 2000 .

[13]  N. Chandrasekaran,et al.  M.D. Simulation of nanometric cutting of single crystal aluminum–effect of crystal orientation and direction of cutting , 2000 .

[14]  N. Chandrasekaran,et al.  Finite element simulation of plane strain plastic–elastic indentation on single-crystal silicon , 2001 .

[15]  K. Kurihara,et al.  CROSS-SECTION TRANSMISSION ELECTRON MICROSCOPE OBSERVATIONS OF DIAMOND-TURNED SINGLE-CRYSTAL SI SURFACES , 1994 .

[16]  Kazutaka Fujita,et al.  JSME Int. J. , 1994 .

[17]  A. E. Gee,et al.  Transmission electron microscopy of nanomachined silicon crystals , 1994 .

[18]  Kirk-Othmer.  Concise Encyclopedia of Chemical Technology , 1982 .

[19]  R. Komanduri,et al.  On the ductile machining of silicon for micro electro-mechanical systems (MEMS), opto-electronic and optical applications , 2001 .

[20]  Irving F. Stowers,et al.  Simulation of Nanometer-Scale Deformation of Metallic and Ceramic Surfaces , 1993 .

[21]  N. Chandrasekaran,et al.  A new method for molecular dynamics simulation of nanometric cutting , 1998 .

[22]  Raghavachari,et al.  Structure and bonding in small silicon clusters. , 1985, Physical review letters.

[23]  Wooten,et al.  Molecular dynamics of silicon indentation. , 1993, Physical review. B, Condensed matter.

[24]  N. Moronuki,et al.  Effect of Material Properties on Ultra Precise Cutting Processes , 1988 .

[25]  George M. Pharr,et al.  New evidence for a pressure-induced phase transformation during the indentation of silicon , 1991 .

[26]  Liangchi Zhang,et al.  Molecular dynamics simulation of phase transformations in silicon monocrystals due to nano-indentation , 2000 .

[27]  R. Komanduri,et al.  Technological Advances in Fine Abrasive Processes , 1997 .

[28]  D. Kuhlmann-wilsdorf.  The theory of dislocation-based crystal plasticity , 1999 .

[29]  Masahiko Yoshino,et al.  Some experiments on the scratching of silicon:: In situ scratching inside an SEM and scratching under high external hydrostatic pressures , 2001 .

[30]  M. C. Shaw.  Metal Cutting Principles , 1960 .

[31]  D. Tabor,et al.  Indentation hardness and semiconductor–metal transition of germanium and silicon , 1978, Nature.

[32]  R. Komanduri,et al.  Some aspects of machining with negative rake tools simulating grinding , 1971 .

[33]  Naoya Ikawa,et al.  Crack Initiation in Machining Monocrystalline Silicon , 1999 .

[34]  Weber,et al.  Computer simulation of local order in condensed phases of silicon. , 1985, Physical review. B, Condensed matter.

[35]  T. Moriwaki,et al.  Machinability of Copper in Ultra-Precision Micro Diamond Cutting , 1989 .

[36]  Donald W. Brenner,et al.  Simulated engineering of nanostructures , 1996 .

[37]  N. Chandrasekaran,et al.  Effect of tool geometry in nanometric cutting: a molecular dynamics simulation approach , 1998 .