Open-Source Automated Mapping Four-Point Probe

Scientists have begun using self-replicating rapid prototyper (RepRap) 3-D printers to manufacture open source digital designs of scientific equipment. This approach is refined here to develop a novel instrument capable of performing automated large-area four-point probe measurements. The designs for conversion of a RepRap 3-D printer to a 2-D open source four-point probe (OS4PP) measurement device are detailed for the mechanical and electrical systems. Free and open source software and firmware are developed to operate the tool. The OS4PP was validated against a wide range of discrete resistors and indium tin oxide (ITO) samples of different thicknesses both pre- and post-annealing. The OS4PP was then compared to two commercial proprietary systems. Results of resistors from 10 to 1 MΩ show errors of less than 1% for the OS4PP. The 3-D mapping of sheet resistance of ITO samples successfully demonstrated the automated capability to measure non-uniformities in large-area samples. The results indicate that all measured values are within the same order of magnitude when compared to two proprietary measurement systems. In conclusion, the OS4PP system, which costs less than 70% of manual proprietary systems, is comparable electrically while offering automated 100 micron positional accuracy for measuring sheet resistance over larger areas.

[1]  Peter Bøggild,et al.  Direct measurement of surface-state conductance by microscopic four-point probe method , 2002 .

[2]  Gavin Conibeer,et al.  Silicon nanostructures for third generation photovoltaic solar cells , 2006 .

[3]  Hongwen Sun.  Recent Progress in Anti-Reflection Layer Fabrication for Solar Cells , 2016 .

[4]  F. Smits.  Measurement of sheet resistivities with the four-point probe , 1958 .

[5]  R. Rymaszewski,et al.  Empirical method of calibrating a 4-point microarray for measuring thin-film-sheet resistance , 1967 .

[6]  Daniel Güllmar,et al.  3D printing of MRI compatible components: why every MRI research group should have a low-budget 3D printer. , 2014, Medical engineering & physics.

[7]  Robert Winkler,et al.  'Plug and Play' assembly of a low-temperature plasma ionization mass spectrometry imaging (LTP-MSI) system. , 2014, Journal of proteomics.

[8]  Joshua M. Pearce,et al.  Building Research Equipment with Free, Open-Source Hardware , 2012, Science.

[9]  Joshua M. Pearce,et al.  A Review of Solar Photovoltaic Levelized Cost of Electricity , 2011 .

[10]  I. Miccoli,et al.  The 100th anniversary of the four-point probe technique: the role of probe geometries in isotropic and anisotropic systems , 2015, Journal of physics. Condensed matter : an Institute of Physics journal.

[11]  Lucia L. Prieto-Godino,et al.  Open Labware: 3-D Printing Your Own Lab Equipment , 2015, PLoS biology.

[12]  Fahid Algahtani,et al.  Four point probe geometry modified correction factor for determining resistivity , 2013, Smart Materials, Nano-, and Micro- Smart Systems.

[13]  Wang Xiaofei,et al.  Design, implementation, and assessment of a high-precision and automation measurement system for thin film resistivity , 2010, 2010 International Conference on Mechanic Automation and Control Engineering.

[14]  Adam Spencer,et al.  Open source and DIY hardware for DNA nanotechnology labs. , 2015, Journal of biological methods.

[15]  Cheng-Kuan Su,et al.  Three-dimensional printed sample load/inject valves enabling online monitoring of extracellular calcium and zinc ions in living rat brains. , 2014, Analytica chimica acta.

[16]  Joshua M. Pearce.  Open-Source Lab: How to Build Your Own Hardware and Reduce Research Costs , 2013 .

[17]  Mikrajuddin Abdullah,et al.  Four point probe method based on LOG112 and C8051F006 SoCs for resistivity measurement , 2009, International Conference on Instrumentation, Communication, Information Technology, and Biomedical Engineering 2009.

[18]  L. Fanni,et al.  Transparent Electrodes in Silicon Heterojunction Solar Cells: Influence on Contact Passivation , 2016, IEEE Journal of Photovoltaics.

[19]  Hong Jiao,et al.  Getting started with open‐hardware: Development and control of microfluidic devices , 2014, Electrophoresis.

[20]  Andrew Blakers,et al.  Semitransparent Perovskite Solar Cell With Sputtered Front and Rear Electrodes for a Four-Terminal Tandem , 2016, IEEE Journal of Photovoltaics.

[21]  Matthew H Todd,et al.  Open science is a research accelerator. , 2011, Nature chemistry.

[22]  Eamon Nash,et al.  I Common Mode and Instrumentation Amplifiers , .

[23]  Bernard Kippelen,et al.  Direct correlation between work function of indium-tin-oxide electrodes and solar cell performance influenced by ultraviolet irradiation and air exposure. , 2012, Physical chemistry chemical physics : PCCP.

[24]  Dietmar Knipp,et al.  On the interplay of interface morphology and microstructure of high-efficiency microcrystalline silicon solar cells , 2016 .

[25]  Luigi Vanfretti,et al.  The OpenPMU Platform for Open-Source Phasor Measurements , 2013, IEEE Transactions on Instrumentation and Measurement.

[26]  Rodney S. Ruoff,et al.  Correction factors for 4-probe electrical measurements with finite size electrodes and material anisotropy: a finite element study , 2007 .

[27]  Joshua M. Pearce,et al.  Exchanging Ohmic Losses in Metamaterial Absorbers with Useful Optical Absorption for Photovoltaics , 2014, Scientific Reports.

[28]  David Bulnes-Abundis,et al.  3D‐printed individual labware in biosciences by rapid prototyping: In vitro biocompatibility and applications for eukaryotic cell cultures , 2015 .

[29]  Daniel Kahn,et al.  An Affordable Open-Source Turbidimeter , 2014, Sensors.

[30]  Joshua M. Pearce,et al.  Plasmonic enhancement of amorphous silicon solar photovoltaic cells with hexagonal silver arrays made with nanosphere lithography , 2016 .

[31]  Chao-Ming Huang,et al.  Physical Characterization and Pre-assessment of Recycled High-Density Polyethylene as 3D Printing Material , 2017, Journal of Polymers and the Environment.

[32]  Bethany C Gross,et al.  Evaluation of 3D printing and its potential impact on biotechnology and the chemical sciences. , 2014, Analytical chemistry.

[33]  Thomas J. Howard,et al.  The Current State of Open Source Hardware: The Need for an Open Source Development Platform , 2013 .

[34]  Joshua M. Pearce,et al.  Free and open‐source automated 3‐D microscope , 2016, Journal of microscopy.

[35]  Masahiro Agu,et al.  Geometrical Correction Factor for Semiconductor Resistivity Measurements by Four-Point Probe Method , 1984 .

[36]  Mitsuhiro Katayama,et al.  Four-point probe resistance measurements using PtIr-coated carbon nanotube tips. , 2007, Nano letters.

[37]  Joshua M. Pearce,et al.  Open-Source 3-D Platform for Low-Cost Scientific Instrument Ecosystem , 2016, Journal of laboratory automation.

[38]  D. Schroder.  Semiconductor Material and Device Characterization , 1990 .

[39]  Vicky Wong,et al.  Zero-Drift Amplifiers : Now easy to use in high precision circuits , 2015 .

[40]  U. Liebel,et al.  Generation of orientation tools for automated zebrafish screening assays using desktop 3D printing , 2014, BMC Biotechnology.

[41]  Joshua M. Pearce,et al.  Open-Source 3D-Printable Optics Equipment , 2013, PloS one.

[42]  Joshua M. Pearce,et al.  A new method of preparing highly conductive ultra-thin indium tin oxide for plasmonic-enhanced thin film solar photovoltaic devices , 2016 .

[43]  L. B. Valdes,et al.  Resistivity Measurements on Germanium for Transistors , 1954, Proceedings of the IRE.

[44]  David S. Perloff,et al.  Four‐Point Probe Correction Factors for Use in Measuring Large Diameter Doped Semiconductor Wafers , 1976 .

[45]  F. Keywell,et al.  Measurement of the Sheet Resistivity of a Square Wafer with a Square Four‐Point Probe , 1960 .

[46]  Rahman Saidur,et al.  Highly efficient antireflective and self-cleaning coatings that incorporate carbon nanotubes (CNTs) into solar cells: A review , 2016 .

[47]  Sune Thorsteinsson,et al.  Accurate microfour-point probe sheet resistance measurements on small samples. , 2009, The Review of scientific instruments.

[48]  Miro Zeman,et al.  Advanced light management based on periodic textures for Cu(In,Ga)Se2 thin-film solar cells. , 2016, Optics express.

[49]  M. A. Logan.  An AC bridge for semiconductor resistivity measurements using a four-point probe , 1961 .

[50]  Mm Martijn Wienk,et al.  Highly Efficient Hybrid Polymer and Amorphous Silicon Multijunction Solar Cells with Effective Optical Management , 2016, Advanced materials.

[51]  Matheus Carvalho de Carvalho,et al.  A low cost, easy to build, portable, and universal autosampler for liquids , 2013 .

[52]  L. J. Swartzendruber,et al.  Four-point probe measurement of non-uniformities in semiconductor sheet resistivity☆ , 1964 .

[53]  R Rymaszewski,et al.  Relationship between the correction factor of the four-point probe value and the selection of potential and current electrodes , 1969 .

[54]  Joshua M. Pearce.  Quantifying the Value of Open Source Hardware Development , 2014, Modern Economy.

[55]  Joshua M. Pearce.  Return on investment for open source scientific hardware development , 2016 .

[56]  Joshua M. Pearce,et al.  Open-source mobile water quality testing platform , 2014 .

[57]  Joshua M. Pearce.  Laboratory equipment: Cut costs with open-source hardware , 2014, Nature.

[58]  Arthur Uhlir,et al.  The potentials of infinite systems of sources and numerical solutions of problems in semiconductor engineering , 1955 .

[59]  Joshua M. Pearce,et al.  Distributed recycling of waste polymer into RepRap feedstock , 2013 .

[60]  Joshua M. Pearce.  Photovoltaics - A Path to Sustainable Futures , 2002 .

[61]  Joshua M. Pearce,et al.  Limitations of ultra-thin transparent conducting oxides for integration into plasmonic-enhanced thin-film solar photovoltaic devices , 2015, Materials for Renewable and Sustainable Energy.

[62]  Parisa Eslambolchilar,et al.  Open-source hardware for medical devices , 2016, BMJ Innovations.

[63]  Joshua M. Pearce,et al.  Multi-resonant silver nano-disk patterned thin film hydrogenated amorphous silicon solar cells for Staebler-Wronski effect compensation , 2014, Journal of Applied Physics.

[64]  D E Vaughan,et al.  Four-probe resistivity measurements on small circular specimens , 1961 .

[65]  Rhys Jones,et al.  RepRap – the replicating rapid prototyper , 2011, Robotica.

[66]  M. Libra,et al.  Effect of the oxygen absorption on properties of ITO layers , 1989 .

[67]  Richard E. Smalley,et al.  Future Global Energy Prosperity: The Terawatt Challenge , 2005 .

[68]  Joshua M. Pearce,et al.  Influence of Oxygen Concentration on the Performance of Ultra-Thin RF Magnetron Sputter Deposited Indium Tin Oxide Films as a Top Electrode for Photovoltaic Devices , 2016, Materials.