The Correlation between Ion Beam/Material Interactions and Practical FIB Specimen Preparation

The focused ion beam (FIB) tool has been successfully used as both a stand alone analytical instrument and a means to prepare specimens for subsequent analysis by SEM, TEM, SIMS, XPS, and AUGER. In this work, special emphasis is given to TEM specimen preparation by the FIB lift-out technique. The fundamental ion/solid interactions that govern the FIB milling process are examined and discussed with respect to the preparation of electron transparent membranes. TRIM, a Monte Carlo simulation code, is used to physically model variables that influence FIB sputtering behavior. The results of such computer generated models are compared with empirical observations in a number of materials processed with an FEI 611 FIB workstation. The roles of incident ion attack angle, beam current, trench geometry, raster pattern, and target-material-dependent removal rates are considered. These interrelationships are used to explain observed phenomena and predict expected milling behaviors, thus increasing the potential for the FIB to be used more efficiently with reproducible results.

[1]  Lucille A. Giannuzzi,et al.  Ion channeling effects on the focused ion beam milling of Cu , 2001 .

[2]  L. Giannuzzi,et al.  Comparative evaluation of protective coatings and focused ion beam chemical vapor deposition processes , 2002 .

[3]  S. Chu,et al.  Microscopic studies of semiconductor lasers utilizing a combination of transmission electron microscopy, electroluminescence imaging, and focused ion beam sputtering , 1993 .

[4]  T. Ishitani,et al.  Focused-ion-beam digging of biological specimens. , 1995, Journal of electron microscopy.

[5]  J. L. Brimhall,et al.  Amorphous phase formation in irradiated intermetallic compounds , 1983 .

[6]  J. Kinney,et al.  Molecular dynamic calculations of energetic displacement cascades , 1981 .

[7]  T. Kamino,et al.  TEM Observation of Micrometer-Sized Ni Powder Particles Thinned by FIB Cutting Technique , 1995 .

[8]  Mark T. Robinson,et al.  Computer simulation of atomic-displacement cascades in solids in the binary-collision approximation , 1974 .

[9]  H. Yamaguchi,et al.  Characteristics of silicon removal by fine focused gallium ion beam , 1985 .

[10]  C. Bulle-lieuwma,et al.  Novel scheme for the preparation of transmission electron microscopy specimens with a focused ion beam , 1993 .

[11]  He,et al.  Mechanistic study of atomic desorption resulting from the keV-ion bombardment of fcc{001} single-crystal metals. , 1995, Physical review. B, Condensed matter.

[12]  B. Prenitzer.  Investigation of variables affecting focused ion beam milling as applied to specimen preparation for electron microscopy: A correlation between Monte Carlo based simulation and empirical observation , 1999 .

[13]  P. Goodhew.  Thin foil preparation for electron microscopy , 1986 .

[14]  R. Hull,et al.  Applications of focused ion beams in microelectronics production, design and development , 1995 .

[15]  James F. Gibbons,et al.  Projected range statistics: Semiconductors and related materials , 1975 .

[16]  L. Giannuzzi,et al.  TEM of Sub-Micrometer Particles using the FIB Lift-Out Technique , 2001, Microscopy and Microanalysis.

[17]  G. Doughty.  Book reviewIon bombardment modification of surfaces: Edited by D. Auciello and R. Kelly , 1986 .

[18]  J. Lindhard,et al.  RANGE CONCEPTS AND HEAVY ION RANGES (NOTES ON ATOMIC COLLISIONS, II) , 1963 .

[19]  A. Petford-Long,et al.  Broad ion beam milling of focused ion beam prepared transmission electron microscopy cross sections for high resolution electron microscopy , 2001 .

[20]  S. Myers,et al.  Precision Tem Sample Preparation Using Focused Ion Beam Marking Strategies , 1991 .

[21]  Á. Barna,et al.  Ion beam induced roughness and its effect in AES depth profiling of multilayer Ni/Cr thin films , 1988 .

[22]  A. Oliva.  Historical Overview on the Fundamentals of Sputtering , 1989 .

[23]  I. Adesida,et al.  Monte Carlo simulation of ion beam penetration in solids , 1982 .

[24]  B. Baker,et al.  Fibxtem— Focussed Ion Beam Milling for TEM Sample Preparation , 1991 .

[25]  R. Hull,et al.  Observation of strong contrast from doping variations in transmission electron microscopy of InP‐based semiconductor laser diodes , 1995 .

[26]  M. Nastasi,et al.  Ion–solid Interactions: Ion range and range distribution , 1996 .

[27]  Á. Barna,et al.  Analysis of the development of large area surface topography during ion etching , 1990 .

[28]  J. Melngailis,et al.  Focused ion beam induced deposition and ion milling as a function of angle of ion incidence , 1992 .

[29]  L. R. Herlinger,et al.  TEM Sample Preparation Using A Focused Ion Beam and A Probe Manipulator , 1996 .

[30]  K. M. Zinn,et al.  Transmission electron microscopy. , 1973, International ophthalmology clinics.

[31]  Hidemi Koike,et al.  Transmission Electron Microscope Sample Preparation Using a Focused Ion Beam , 1994 .

[32]  R. B. Irwin,et al.  Transmission electron microscope specimen preparation of Zn powders using the focused ion beam lift-out technique , 1998 .

[33]  J. Biersack,et al.  A Monte Carlo computer program for the transport of energetic ions in amorphous targets , 1980 .

[34]  C. Tung,et al.  Precision transmission electron microscopy sample preparation using a focused ion beam by extraction method , 1997 .

[35]  C. Vartuli,et al.  Application of focused ion beam lift‐out specimen preparation to TEM, SEM, STEM, AES and SIMS analysis , 2001 .

[36]  S. Aoki,et al.  Layer structure evaluation of multilayer x‐ray mirror by combination of focused ion beam etching and transmission electron microscopy , 1993 .

[37]  L. Giannuzzi,et al.  Wet thermal oxidation of GaN , 1999 .

[38]  R. J. Young,et al.  An application of scanned focused ion beam milling to studies on the internal morphology of small arthropods , 1993 .

[39]  O. Auciello,et al.  Ion Bombardment Modification of Surfaces: Fundamentals and Applications , 1984 .

[40]  Yuh‐Lin Wang,et al.  Imaging microanalysis of surfaces with a focused gallium probe , 1988 .

[41]  Tetsuya Saito,et al.  Microstructural Observation of Focused Ion Beam Modification of Ni Silicide/Si Thin Films , 1996 .

[42]  R. J. Young,et al.  Characteristics of gas‐assisted focused ion beam etching , 1993 .

[43]  H. Ahmed,et al.  Fabrication of Planar and Cross-Sectional TEM Specimens Using a Focused Ion Beam , 1990 .

[44]  S. Minagawa,et al.  Focused ion beam micromachining for transmission electron microscopy specimen preparation of semiconductor laser diodes , 1992 .

[45]  Steve R Brown,et al.  Applications of the FIB lift‐out technique for TEM specimen preparation , 1998, Microscopy research and technique.

[46]  Lucille A. Giannuzzi,et al.  Focused Ion Beam Milling and Micromanipulation Lift-Out for Site Specific Cross-Section Tem Specimen Preparation , 1997 .