Effect of manufacturing processes on contact resistance characteristics of metallic bipolar plates i

Abstract In this study, metallic bipolar plate (BPP) samples manufactured with stamping and hydroforming under different process conditions were tested for their electrical contact resistance characteristics to reveal the effect of manufacturing type and conditions. Punch speed and force in stamping, and pressure and pressure rate in hydroforming were selected as variable process parameters. In addition, two different channel sizes were tested to expose the effect of BPP micro-channel geometry and its consequences on the contact resistance. As a general conclusion, stamped BPPs showed higher contact conductivity than the hydroformed BPPs. Moreover, pressure in hydroforming and geometry had significant effects on the contact resistance behavior of BPPs. Short term corrosion exposure was found to decrease the contact resistance of bipolar plates. Results also indicated that contact resistance values of uncoated stainless steel BPPs are significantly higher than the respective target set by U.S. Department of Energy. Conforming to literature, proper coating or surface treatments are necessary to satisfy the requirements.

[1]  Jürgen Garche,et al.  Encyclopedia of electrochemical power sources , 2009 .

[2]  Jun Ni,et al.  Flow channel shape optimum design for hydroformed metal bipolar plate in PEM fuel cell , 2008 .

[3]  P. J. Sebastian,et al.  Conducting polymer-coated stainless steel bipolar plates for proton exchange membrane fuel cells (PEMFC) , 2005 .

[4]  P. Aldebert,et al.  Internal hydration H2/O2 100 cm2 polymer electrolyte membrane fuel cell , 1995 .

[5]  Michio Hori,et al.  Study on metallic bipolar plate for proton exchange membrane fuel cell , 2006 .

[6]  R. Mallant,et al.  Use of stainless steel for cost competitive bipolar plates in the SPFC , 2000 .

[7]  Muammer Koç,et al.  Effect of manufacturing processes on formability and surface topography of proton exchange membrane fuel cell metallic bipolar plates , 2010 .

[8]  Viral S. Mehta,et al.  Review and analysis of PEM fuel cell design and manufacturing , 2003 .

[9]  A. Heinzel,et al.  FUEL CELLS – PROTON-EXCHANGE MEMBRANE FUEL CELLS | Bipolar Plates , 2009 .

[10]  D. Hodgson,et al.  A review of metal separator plate materials suitable for automotive PEM fuel cells , 2009 .

[11]  Jayanti Sinha,et al.  Direct Hydrogen PEMFC Manufacturing Cost Estimation for Automotive Applications , 2010 .

[12]  R. Hornung,et al.  Bipolar plate materials development using Fe-based alloys for solid polymer fuel cells , 1998 .

[13]  Donald G. Baird,et al.  The development of economical bipolar plates for fuel cells , 2006 .

[14]  Heli Wang,et al.  Stainless steel as bipolar plate material for polymer electrolyte membrane fuel cells , 2003 .

[15]  R. A. Antunes,et al.  Corrosion of metal bipolar plates for PEM fuel cells: A review , 2010 .

[16]  Osamu Kobayashi,et al.  Mass production cost of PEM fuel cell by learning curve , 2004 .

[17]  Ramana G. Reddy,et al.  Effect of channel dimensions and shape in the flow-field distributor on the performance of polymer electrolyte membrane fuel cells , 2003 .

[18]  Bruno G. Pollet,et al.  Polymer Electrolyte Membrane Fuel Cell (PEMFC) Flow Field Plate: Design, Materials and Characterisation , 2010 .

[19]  Paul Leonard Adcock,et al.  Bipolar plate materials for solid polymer fuel cells , 2000 .

[20]  Heli Wang,et al.  Pre-oxidized and nitrided stainless steel alloy foil for proton exchange membrane fuel cell bipolar plates: Part 1. Corrosion, interfacial contact resistance, and surface structure , 2010 .

[21]  Linfa Peng,et al.  Effect of dimensional error of metallic bipolar plate on the GDL pressure distribution in the PEM fuel cell , 2009 .

[22]  Yair Ein-Eli,et al.  Reduced contact resistance of PEM fuel cell's bipolar plates via surface texturing , 2007 .

[23]  Yuyan Shao,et al.  Proton exchange membrane fuel cell from low temperature to high temperature: Material challenges , 2007 .

[24]  Jean-Pierre Petit,et al.  Electrical contact resistance between stainless steel bipolar plate and carbon felt in PEFC: A comprehensive study , 2009 .

[25]  Shuo-Jen Lee,et al.  PVD Coated Bipolar Plates for PEM Fuel Cells , 2005 .

[26]  Juncai Sun,et al.  Study on behavior of plasma nitrided 316L in PEMFC working conditions , 2008 .

[27]  A. J. Appleby,et al.  Fuel cell technology: Status and future prospects☆☆☆ , 1996 .

[28]  Chi-Yuan Lee,et al.  The Resistive Properties of Proton Exchange Membrane Fuel Cells With Stainless Steel Bipolar Plates , 2010 .

[29]  M. Koç,et al.  Effect of manufacturing conditions on the corrosion resistance behavior of metallic bipolar plates in proton exchange membrane fuel cells , 2011 .

[30]  Heli Wang,et al.  Anodic behavior of high nitrogen-bearing steels in PEMFC environments , 2008 .

[31]  Nigel P. Brandon,et al.  Review of Materials and Characterization Methods for Polymer Electrolyte Fuel Cell Flow-Field Plates , 2007 .

[32]  M. Koç,et al.  Corrosion resistance characteristics of stamped and hydroformed proton exchange membrane fuel cell metallic bipolar plates , 2010 .

[33]  J. Petit,et al.  Corrosion resistance of stainless steel bipolar plates in a PEFC environment: A comprehensive study , 2010 .

[34]  Werner Lehnert,et al.  Investigation on the influence of channel geometries on PEMFC performance , 2006 .

[35]  Ching-Han Huang,et al.  Investigation of PVD coating on corrosion resistance of metallic bipolar plates in PEM fuel cell , 2003 .

[36]  Eric Fleury,et al.  Development of metallic glasses for bipolar plate application , 2007 .

[37]  D. Mahajan,et al.  Metal bipolar plates for PEM fuel cell—A review , 2007 .

[38]  Karren L. More,et al.  Preferential thermal nitridation to form pin-hole free Cr-nitrides to protect proton exchange membrane fuel cell metallic bipolar plates , 2004 .

[39]  Life-Limiting Aspects of the Corrosion of Metallic Bipolar Plates for PEM Fuel Cells , 2008 .

[40]  Kyu Taek Cho,et al.  Coupled effects of flow field geometry and diffusion media material structure on evaporative water r , 2010 .

[41]  EunAe Cho,et al.  Performance of a 1 kW-class PEMFC stack using TiN-coated 316 stainless steel bipolar plates , 2005 .

[42]  Jun Ni,et al.  Robust design of assembly parameters on membrane electrode assembly pressure distribution , 2007 .

[43]  Allen M. Hermann,et al.  Bipolar plates for PEM fuel cells: A review , 2005 .

[44]  J. Wind,et al.  Metallic bipolar plates for PEM fuel cells , 2002 .

[45]  John A. Turner,et al.  Reviewing Metallic PEMFC Bipolar Plates , 2010 .